Table of Contents
Summary of Contents for SPXFLOW Colloid Mill
- Page 1 I N S T R U CT I O N M A N UA L Colloid Mill F O R M N O . : 9 5 - 0 3 0 2 8 R E V I S I O N : 0 9 / 2 0 1 9...
- Page 2 611 Sugar Creek Road Delavan, WI 53115 Phone: (262)728-1900 or (800)252-5200 Fax: (262)728-4904 or (800)252-5012 E-mail: wcb@spxflow.com Website: www.spxflow.com Information contained in this manual is subject to Copyright © 2019 SPX FLOW, Inc. change without notice and does not represent a All Rights Reserved.
-
Page 3: Table Of Contents
Warranty Claim ............................4 Safety ............................ 5 Warnings and Replacement Labels ......................6 Introduction/Specifications..................... 6 Specifications ............................... 6 Colloid Mill Unit Dimensions ........................7 Installation and Start-Up ......................8 Variation of inlet port ............................ 8 Overhead equipment ........................... 8 Wiring ................................8 Rotation ................................ -
Page 4: Warranty
Warranty Waukesha Cherry-Burrell Brand Colloid Mill ® Warranty LIMITED WARRANTY: Unless otherwise mutually agreed to in writing, (a) SPX FLOW US, LLC (SPX FLOW) goods, auxiliaries and parts thereof are warranted to the Buyer against defective workmanship and material for... -
Page 5: Safety
Waukesha Cherry-Burrell Brand Colloid Mill Safety ® Safety READ AND UNDERSTAND THIS MANUAL PRIOR TO INSTALLING, OPERATING, OR SERVICING THIS EQUIPMENT SPX FLOW recommends users of our equipment and designs follow the latest Industrial Safety Standards. At a minimum, these should include the industrial safety requirements established by: 1. -
Page 6: Warnings And Replacement Labels
Replacement Label 33-62 Introduction/Specifications The Waukesha Cherry-Burrell brand Colloid Mill produces controlled, highly sheared, uniform dispersions and stable emulsions made up of uniform globules of moderate fineness. A serrated conical stator and a serrated rotating cone make up the emulsifying head. -
Page 7: Colloid Mill Unit Dimensions
Waukesha Cherry-Burrell Brand Colloid Mill Introduction/Specifications ® Colloid Mill Unit Dimensions 26.81 [681] AS SHOWN, WITH STATOR ALL THE WAY IN 27.94 [710] WITH STATOR ALL THE WAY OUT 1/4-18 NPT PIPE NIPPLE SEAL 9.38 [238] MIN. 17.44 [443] FLUSH INLET 10.51 [267] MAX. -
Page 8: Installation And Start-Up
Installation and Start-Up Waukesha Cherry-Burrell Brand Colloid Mill ® Installation and Start-Up Indicator Knurled Lock Screw Pointer Inlet Inlet Inlet ROTATION Counter-clockwise when facing the Outlet Outlet Outlet Outlet outlet port. Inlet Position 1 Position 2 Position 3 Position 4... -
Page 9: Lubrication
Waukesha Cherry-Burrell Brand Colloid Mill Colloid Mill Troubleshooting ® Lubrication The mill is shipped with oil in the bearing case. The level should be checked at the oil level hole and if necessary, oil should be added Breather cap through the oil fill hole. -
Page 10: Maintenance
Maintenance Waukesha Cherry-Burrell Brand Colloid Mill ® Maintenance Cleaning Handle all parts carefully to avoid nicks and CAUTION scratches which will be detrimental to the operation of the mill. Flushing In some instances the unit can be cleaned by flushing water through it while the mill is in operation. - Page 11 Waukesha Cherry-Burrell Brand Colloid Mill Maintenance ® 6. Remove the rotor retaining nut, then remove the O-ring from the nut. (See Figure 10.) 7. Slide the rotor off the shaft, making sure to handle it with care to avoid damage to the rotor or to the seal seat, which is con- tained in the rotor.
-
Page 12: Assembly
Maintenance Waukesha Cherry-Burrell Brand Colloid Mill ® Assembly Large (1/4”) hole 1. Apply a suitable lubricant to all O-rings and insert them in their Small (1/8”) hole respective grooves. (OUT) (IN) NOTE: Place the seal seat O-ring over the seal seat and then insert the seat into the rotor. -
Page 13: Flush Water Seal Replacement
Waukesha Cherry-Burrell Brand Colloid Mill Maintenance ® Flush Water Seal Replacement 1. Disassemble as described in “Disassembly” on page 10. 2. Remove the four body nuts (Figure 22). Figure 22 - Remove body nuts (4) 3. Slide the body forward off the shaft (Figure 23). -
Page 14: Gear Case Service
Maintenance Waukesha Cherry-Burrell Brand Colloid Mill ® Gear Case Service To avoid a cutting injury, wear gloves and handle CAUTION parts carefully. Tools required for seal and/or bearing replacement: • Assorted hand tools including soft hammer. • Bearing puller or press. -
Page 15: Sanitary Seal Replacement
Waukesha Cherry-Burrell Brand Colloid Mill Maintenance ® Front bearing 4. Clean and lubricate all parts thoroughly before reassembling. NOTE: Do not unwrap the new bearings until ready to install. 5. Lubricate the inner races and press the new bearings onto the shaft. -
Page 16: Parts List
Maintenance Waukesha Cherry-Burrell Brand Colloid Mill ® Parts List Colloid Mill Gear Case DP100-003 DP100-005a 09/2019 95-03028... - Page 17 Waukesha Cherry-Burrell Brand Colloid Mill Maintenance ® Colloid Mill Gear Case ITEM NO. DESCRIPTION PART NO. NOTES Gear Case 0MS005000 Drive Shaft 0MS008000 Front Bearing 0MS036300 Bearing Locknut 0MS036N00 Rear Bearing 0MS036000 Retaining Ring BD0087R00 Front Bearing Retainer Gasket 0MS042B00...
-
Page 18: Colloid Mill Fluid Head
Maintenance Waukesha Cherry-Burrell Brand Colloid Mill ® Colloid Mill Fluid Head 30 44 NOTE: Body rotor clearance starts at 0.101” and ends at 0.220” in increments of 0.010” NOTE: Torque rotor nuts to 75 ft-lb DP100-005 Used to set adjusting ring at minimum setting of 0.010”... - Page 19 Waukesha Cherry-Burrell Brand Colloid Mill Maintenance ® Colloid Mill Fluid Head ITEM NO. DESCRIPTION PART NO. NOTES Body, 2” Bevel Seat 0MS001000 Body, 2” TCF 35886+ Seal Seat & Body O-ring, FKM V70150 Seal Seat & Body O-ring, Silicone S75150...
-
Page 20: Sanitary Seal
Maintenance Waukesha Cherry-Burrell Brand Colloid Mill ® Sanitary Seal 19 16 DP100-004 Item No. Description Part No. Gland Gasket 0MS042G00 Gland Plate 0MS058200 Gland Plate Lip Seal 0MS030200 Spring 0MS304200 Stationary Seal, Carbon 0MS306003 Stationary Seal, Silicon Graphite 0MS306004 Stationary Seal, Silicon Carbide... - Page 22 Please contact your local sales representative for product availability in your region. For more information visit www.spxflow.com. The green “>” is a trademark of SPX FLOW, Inc. ISSUED 09/2019...
Need help?
Do you have a question about the Colloid Mill and is the answer not in the manual?
Questions and answers