T.MT5310.61A (DVB-T+C+T2)-SPECIFICATION 1. GENERAL DESCRIPTION T.MT5310.61A is a digital and analog TV control board, which is suitable for Pan Europe and UK market. It can support less than 26 inch LED panels which resolution is up to 1920×1080. T.MT5310.61A can receive and decode both Free-To-Air DTV and CA DVB-T, DVB-C, DVB-T2 program.
T.MT5310.61A (DVB-T+C+T2)-SPECIFICATION FRONT VIEW OF T.MT5310.61A Earphone DC Power HDMI PC-RGB PC Audio CVBS& CVBS Audio & Component SCART Supply Component Audio In SIDE VIEW OF T.MT5310.61A Coaxial Out RF In CI Slot In RJ45 In USB Slot In REQUIREMENT OF WIRE HARNESS(optional) AV In COMPONENT In 3.FEATURES...
T.MT5310.61A (DVB-T+C+T2)-SPECIFICATION 4. PCB DIMENSIONS The size of T.MT5310.61A is 185.5mm(L)*147.5mm(W)*22mm(H). Ver . V1.1 Description EARPHONE OUT DC IN HDMI IN VGA IN PC AUDIO IN SCART AV IN YPbPr IN COAX OUT RF IN CI SLOT RJ45 IN USB IN 第...
T.MT5310.61A (DVB-T+C+T2)-SPECIFICATION 5. SCHEMATICS OF IR BOARD & KEY BOARD 6. INTERFACE DEFINITION The optional connectors are marked with “*”. ◆ *CN2(10PIN/2.0): MAIN POWER SUPPLY & INVERTER CONNECTOR SYMBOL DESCRIPTION +12V DC Power Supply Back-Light ON/OFF Control for Panel Brightness Adjustment for Panel Ground ◆...
Page 9
T.MT5310.61A (DVB-T+C+T2)-SPECIFICATION SYMBOL DESCRIPTION Ground ◆ *CN6(6PIN/2.0): 5V POWER SUPPLY CONNECTOR SYMBOL DESCRIPTION +5V DC Power Supply Ground 5VSB +5V DC Power Supply for Standby Mode PWON Power On/Off ◆ CN10(14PIN/2.0): IR & Key BOARD CONNECTOR SYMBOL DESCRIPTION +5V DC Power Supply Red Indicator Green Indicator IR Receiver...
Page 10
T.MT5310.61A (DVB-T+C+T2)-SPECIFICATION SYMBOL DESCRIPTION TXOC- LVDS ODD Clock- Signal TXOC+ LVDS ODD Clock+ Signal TXO3- LVDS ODD 3- Signal TXO3+ LVDS ODD 3+ Signal TXE0- LVDS EVEN 0- Signal TXE0+ LVDS EVEN 0+ Signal TXE1- LVDS EVEN 1- Signal TXE1+ LVDS EVEN 1+ Signal TXE2- LVDS EVEN 2- Signal...
Page 11
T.MT5310.61A (DVB-T+C+T2)-SPECIFICATION SYMBOL DESCRIPTION Ground DVD Component-Pr Input Ground DVD Component-Y Input Ground 7. CONFIGURATION & GENERAL PRECAUTIONS Relative humidity: ≤ 80%. Storage temperature: -10~60° C. Operation temperature: 0~40° C. Protect the board from static electricity in case of damage to the IC. ...
Page 26
1. Power Supply Overview 电性能指标:LK-PL240405A 1.1 Table 1 Input Electrical Characteristics Overview ( ) 输 入特性 Input voltage range 输入电压范围 90Vac-264Vac Normal voltage range 100Vac-240Vac 标准输入 Frequency range 频率范围 50Hz/60Hz Max input AC current 满载输入电流 100Vac/1.5A Max Inrush current (cold start) 浪涌电流(冷机)...
Page 27
1.5 LED General Requirements 1.5.1 Table 1 Input Electrical Characteristics Overview ( 输 入特性) PARA METER SYMBOL TYPICAL UNIT REMARK 参 数 符 号 最小值 典 型 值 最大值 单 位 备 注 INPUT VOLTAGE 11.4 12.6 输入电压 NPUT CURRENT Vin=12V,Von/off=5V 1.22 1.45...
Page 28
2.Pin Connection(连接器脚位定义) Power supply connectors (电源输入/输出端子)AC INPUT(交流输入) Location (位置): CON1 Connector type (端子型号): 3.96mm-3Pin Pin assignments: Table. Symbol Pin No Description (符号) (引脚号) (描述) DC Input(直流输入) : Location (位置): CON2 Connector type (端子型号): JST S6B-PH-K-S or equivalent Pin assignments: Table. (2.0mm -6Pin) Symbol Pin No Description...
Page 29
5. EMC (电磁兼容性) 5.1 EMI(电磁干扰) The power supply shall compliance with the following Criterion: 电源电磁干扰满足下列规则: 1)Conduction Emission:( ) 传导干扰度 EN55022, CLASS B GB9254,CLASS B FCC PART15 CLASS B 2) Radiate Emission:( ) 辐射干扰度 EN55022, CLASS B GB9254,CLASS B FCC PART15 CLASS B 5.2 EMS(电磁干扰)...
Page 32
LK-SP104804A 1. Power Supply Overview 电性能指标: 1.1 Table 1 Input Electrical Characteristics Overview (输入特性) Input voltage range 90Vac to 264Vac 输入电压 Normal voltage range 标称输入 100Vac to 240Vac Frequency range 频率范围 50Hz/60Hz±5% Max input ac current 1.5Amax at full load condition 满载输入电流...
Page 33
LK-SP104804A 2) Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate system loading. 离电源板大于 30CM 处输出电源端并联 0.1uF 的陶瓷电容和 10uF 的电解电容来模拟负载测试 1.2.3 Output Transient Response. (输出动态响应) Table 4. Test condition.测试条件 Voltage Tolerance Limit Slew Rate Load Change 12±5%...
Page 34
LK-SP104804A 1.2.7 Table8 AC turn-on delay time( 开机输出延迟时间) 开机输出延迟时间 ≤ 2S 1.3 Protection: (保护功能) 1.3.1 Table 9 DC output Over Voltage Protection. (输出过压保护) Output Voltage Max. Over Voltage Comments +12V Hiccup 尝试重复启动 Note: The power supply shall be test at max AC voltage (264Vac) and min load or no load. 应该在最大交流输入电压...
Page 35
LK-SP104804A (绝缘性能) 2. Isolation 2.1 Table 12 (绝缘阻抗) Input To Output DC500V 50MΩmin (at room temperature) Note: 2.2 Table 13 (绝缘耐压) Input To Output 3000Vac 50Hz 1minute ≤ 10mA 3. Safety (安全规格) The power supply shall compliance with the following Criterion: 电源安全性满足下列标准...
Page 36
LK-SP104804A 4.2 EMS (电磁抗扰) The power supply shall compliance with the following Criterion: 电源电磁抗扰满足下列规则: 1) ESD (静电抗扰度) *GB17626.2-1998/IEC61000-4-2 2) EFT (脉冲群抗扰度) *GB17626.4-1998/IEC61000-4-4 3) Surge (雷击浪涌) *GB17626.5-1998/IEC61000-4-5 L to N 1KV,L、N to FG 2KV 5. Environmental Requirement (工作环境) 5.1 Temperature (环境温度) * Operating: -10℃...
Page 37
LK-SP104804A (连接器脚位定义) 9. Pin Connection TYPE : 2.0MM*6PIN Table 14 CON2 Connection And Function Pin Connection Function +12V +12V TYPE : 2.0MM*12PIN Table 15 CON3 Connection And Function Pin Connection Function Table 16 CON1 Connection And Function Pin Connection Function AC-L AC INPUT LINE AC-N...
Page 39
LK-SP104804A Mount Method( 装配注意事项 ) Table 17 ≤ 5.5mm (1*) ≥ 6.0mm 130.0m Note: Mount the unit to the mounting SPS UNIT board using M3 screw. The maximum value of the tightening torque is 0.4N-M. The insertion depth of the screw should be less 5.5mm.
STV-22LED3 BOM LIST Part No qunty for unit Description BMT5310-61B-- main board BXATB004----- Tuner 06PL2405A1LK power board with mylar 23PL2405A45LK Mylar BAD0007A----I IR Board Ass'y BAD0008A----I KEY Board Ass'y 17M215XW031YD LED panel JBD551-V001-I IR/key board connecting cable power cord JP2162------I...
Page 43
STV-24LED3 BOM LIST Part No qunty for unit Description BMT5310-61B-- main board BXATB004----- Tuner BPE0022A----I power board with mylar BL-DCDC5----I DC/DC board BAD0007A----I IR Board Ass'y BAD0008A----I KEY Board Ass'y BFL001------I LED panel JBD601-V001-I IR/key board connecting cable JP2162------I power cord JW4451-C005-I speaker connector JWA181-V003-I...
Page 45
1. 1. Power Supply Troubleshooting Power Supply Troubleshooting Check if E8 Check if E8 is 5V? Check U5 and the Check if U12_PIN2 is 3.3V? circuit of U5 Power on and check if R115 Power on and check if R115 Change U12 is 3.3V? Check if PIN3 of Q10 is...
Page 46
2. 2. Display Troubleshooting (Exceptional Screen / White Screen) E ceptional Screen Exceptional Screen / White Screen Is upgrade software OK? Old software is wrong. Check if the LVDS cable is correct and connected tightly Check if the voltage of CN11_PIN1 is OK?...
Page 47
3. 3. Display Troubleshooting (Black Screen) Black Screen Check if backlight is OK? Reference to the maintenance process of "Exceptional screen / Whit White screen" " Check if the voltage of CN3_PIN3 (BLON Signal) is high level Check if the voltage of CN3_PIN4 is normal? 1 Check Q3 and surrounding components 1、Check Q3 and surrounding components.
Page 48
4. Audio Trouble 4. Audio Troubleshooting All Channels No Sound Check if Volume and MUTE Settings are normal? Check if there is signal on CN17? Check if U10_PIN7 is 12V? k if U10 PIN7 i 12V? Check if the voltage of k if th U10_PIN8 is higher than 8.5V Check if U1_PIN201,203...
Page 49
5. Audio Troubleshooting( ( SCART/PC/AV/ No Sound) ) 5. Audio Trouble SCART/PC/AV/YPbPr YPbPr No Sound SCART/PC/AV/ SCART/PC/AV/YPbPr SCART/PC/AV/ SCART/PC/AV/YPbPr YPbPr No Sound YPbPr No Sound No Sound No Sound Reference to the Check if other maintenance process of “All Channels No All Channels No channels are no sound? Sound”...
Page 50
6. Function Trouble 6. Function Troubleshooting ATV/DVB-T/DVB-C can't scan any channel ( ( ATV/DVB T/T2/C) ) ATV/DVB- - T/T2/C 1.Check if the external RF input signal is normal. 2.Check if the country, region and standard are set correctly. Check if the voltage Check if the voltage of Check if T1_PIN10、11 of U14_PIN3 is 5V?
Page 51
7. Function Trouble 7. Function Troubleshooting (HDMI) (HDMI) HDMI does not has the signal 1 .HDMI interface false welding 2 .System setting wrong , do “reset” 第 51 页,共 57 页...
Page 52
8.Function Trouble 8.Function Troubleshooting (PC) (PC) PC Channel PC Channel Image Picture is No signal Color fade Dithering not in center Check if the R,G,B input signals Check if the VS,HS input signals of U1_PIN152~156 are normal? of U1_PIN150,151 are normal? OSD setting Check the circuit The data of...
Page 53
9.Function Trouble 9.Function Troubleshooting (SCART) (SCART) SCART Channel SCART Channel SCART SCART-OUT SCART SCART-OUT Can’t automatically No Signal No Sound color fade No Signal switch to SCART channel Check if the Check the Check if the Check the R,G,B input Check the circuit circuit between voltage of...
Page 54
10. Function Trouble 10. Function Troubleshooting (AV, (AV,YPBPR) ) YPbPr No Signal / Color Fade CVBS N Si No Signal Check if the 5V power Check if supply of U13_PIN16 U16_PIN4,7,9 and control signal of Check if the have signals? have signals? Check if C58 Check if C58...
SOFTWARE UPDATE: Copy the BIN file to USB, when the TV in the standby state ,Insert the USB to main board . This indicator lights. When the light is extinguished, software upgrade complete. 第 57 页,共 57 页...
Need help?
Do you have a question about the STV-22LED3 and is the answer not in the manual?
Questions and answers