Minetan Bronze Babe Personal Operation Manual

IMPORTANT SAFETY PRECAUTIONS

Before using this Tan.Easy Product, read all instructions and cautionary markings
in this manual and on the device. When using an electrical appliance, basic
precautions should always be followed:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
1. Do not leave product when plugged in. Unplug from outlet when not in use and
before servicing.
2. Indoor Use ONLY. Do not use outdoors or on wet surfaces. Store Indoor ONLY.
3. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
4. This product is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
5. Use this device only for its intended function and do not use attachments not
recommended by the authorized Tan.Easy Pro Tools manufacturer.
6. Do not use the device if the cord is damaged. In the event of damage
discontinue use immediately. If the supply cord is damaged, it must be replaced
by the authorized Tan.Easy Pro Tools manufacturer.
7. If device is not working as it should, has been dropped, damaged, left outdoors,
or dropped into water, do not use, contact Tan.Easy Pro Tools Customer Care via
the website or regional telephone number.
8. Do not pull or carry by cable, use cable as a handle, close a door on cable,
or pull cable around sharp edges or corners. Keep cable away from heated
surfaces.
9. Do not unplug by pulling on cable. To unplug, grasp the plug, not the cable.
10. Do not handle plug with wet hands.
11. Turn off all controls before unplugging.
12. Do not spray flammable or combustible liquids, such as gasoline, or use in areas
where they may be present.
13. Do not use without the filter in place.
14. Do not use an extension cord unless the cord complies with local region
electrical safety standards.
15. Periodically inspect the power cord for signs of damage
16. Do not use a fluid having a flash point higher than 60ºC. When a combustible
liquid is sprayed there can be danger of fire or explosion, especially in a closed
area. Read instruction manual before operating.
17. Fuse is only able to be replaced by manufacturer.
IMPORTANT: This device is designed for 220-240V or 120V respectively depending on
region. Always check that the voltage of your electricity supply matches the voltage
of your Tan.Easy Pro Tools device.
1. Do not use this product with a voltage inverter or any device designed to convert
the electrical supply to 220-240V or 120V from a different source.
2. Always ensure that your appliance
is connected to a properly earthed
power supply. Your Tan.Easy Pro Tools
Device is a class II electrical appliance.
Do not pull
on cables.

FAILURE TO OPERATE

In the unlikely event that your Tan.Handy device does not operate correctly,
check that the Tan.Handy product and main power supply are switched on, and
that power is available.
For UK plugs, please ensure that the fitted fuse is intact and functioning; if it is not,
replace it with an identically rated British Standard Fuse.
If in doubt or for further advice, please visit the Support and Trouble shooting
page at taneasyprotools.com or contact an approved Tan.Easy stockist or
contact Tan.Easy Customer services for further advice.

CUSTOMER CARE

Thank you for choosing to purchase this Tan.Easy Pro Tools product. Your Tan.Easy Pro
Tools device will be covered for parts only for 12 months from the date of purchase, as
detailed in the terms of the Tan.Easy Pro Tools guarantee on taneasyprotools.com.
If you have a query about your Tan.Easy Pro Tools product, contact Tan.Easy Pro Tools
by going to the website taneasyprotools.com.
Most queries can be solved by our frequently asked questions online. Alternatively you
can contact your local Tan.Easy representative in your region.
Please state your serial number for any warranty claims you have. Your serial number
can be found on the rating plate, which is on the base of your machine or below:
This is for example purposes only. Note your serial number for future reference
SERIAL NUMBER

TROUBLESHOOTING

REVISION DATE 9.07.15 #1
All rights are reserved. No part of this document may be photocopied, reproduced
or translated to another language without prior written consent of Tan.Easy Pro
Tools.NOTICE
The information contained in this document is subject to change without notice
and should not be construed as a commitment by Tan.Easy Pro Tools. Tan.Easy Pro
Do not submerge Do not use near
in water or get wet. open flames
Tools assumes no responsibility for any errors that may appear in this document nor
does it make expressed or implied warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. Tan.Easy Pro Tools shall not be liable for incidental
or consequential damages in connection with or arising out of the use of this
document and the program material.
FOR TROUBLE SHOOTING & SUPPORT GO TO
TANEASYPROTOOLS.COM
SERIAL
NUMBER
TAN.HANDY MOBILE SPRAY TAN GUN
ITEM NO# 1001001 M1002-18000
150W 120V~60HZ 1.2A
TAN.EASY PRO TOOLS
80 Market St, South Melbourne, 3205 TANEASYPROTOOLS.COM
FOR MORE INFORMATION SEE OPERATION MANUAL MADE IN CHINA
SERIAL
NUMBER
TAN.HANDY MOBILE SPRAY TAN GUN
ITEM NO# 1001001 M1002-18000
150W 240V~60HZ 1.2A
TAN.EASY PRO TOOLS
80 Market St, South Melbourne, 3205 TANEASYPROTOOLS.COM
FOR MORE INFORMATION SEE OPERATION MANUAL MADE IN CHINA
Refer to taneasyprotools.com
BRONZE BABE
PERSONAL
SPRAY TAN KIT
T A N . H A N D Y O P E R A T I O N M A N U A L
PARTNERING WITH TAN.EASY PRO TOOLS
The MineTan Tan.Handy has been designed by the team
at Tan.Easy Pro Tools, the experts in professional tanning
equipment, to give you the perfect spray tan at home.
ASSEMBLY
1. To begin, attach the
Tan.Handy spray tan gun to
the Tan.Handy mini turbine
by inserting the bottom of
the handle of the spray tan
gun into the connector of
the mini-turbine.
2. Attach the Tan.Handy
spray tan gun with the
'quick-connect' style fitting.
This will lock the spray tan
gun firmly into place.
3. Once the spray tan REMOVING THE SPRAY TAN GUN
gun is attached to the
To remove the Tan.Handy mini-
mini-turbine, insert the
turbine for cleaning and refilling
power cord into the
solution cup, detach the spray
device and in the wall
gun with the 'quick-connect'
plug and turn power
fitting and remove it from the
on at the wall switch.
mini-turbine.
REGISTER YOUR 12 MONTH GUARANTEE
TANEASYPROTOOLS.COM