Subscribe to Our Youtube Channel
Related Manuals for DVC 5370
Summary of Contents for DVC 5370
- Page 1 TYPE 5370 INSTALLATION, OPERATION AND MAINTENANCE MANUAL TYPE 5320 Mechanical limit switch with valve and LED...
- Page 2 The technical specification in chapter 8 should be kept in mind. It should be complied with health and safety principle in the installation and use of Type 5370 controller. To inspect and make sure the valve/controller is intalled and the valve shaft placed correctly before powering on.
- Page 3 The valve/actuator is equipped with rotating part so it should be operated prudently in installing Type 5370. When connecting with compressed air, do not reach your hand or finger into piston or indicated part. Otherwise, it will lead to serious personal injury.
- Page 4 3. Instruction of version features and button operation 3. 1.Description Type 5370 is a pneumatic controller which is designed for process control of valve. It is compatible with most PLC (programmable logic controller) automatic system, with digital communication or AS-I BUS.
- Page 5 C-TOP-1561-33 AS-I Bus version is euipped with the following Signal selection function： - Position self-adjusting Tacit approval - IO (PNP) - Deviation of positional accuracy ±0.5mm - Warning of positional deviation (prevent valve from slight leak) - Function of manual operation - Blue LED light: indicating the valve is turned on - Red LED light: indicating the valve is turned off - Red LED light flickers: indicating it doesn't reach target position or valve position is deviated by pipeline...
- Page 6 3. 3. COMPONENTS Transparent cover Gland cover Bottom seat Air supply connector，BSPT 1/8，1-PC Junction Box BSPT 1/8" Note: 1561 control the internal setting of two 3-way solenoid valve; 1) When a single acting pneumatic valve, with a plug plug one of the working mouth; 2) double acting pneumatic valve is no need to 3.3.1 Function setting and button operation plug the working mouth;...
- Page 7 3.4. Function setting and button operation 156123 & 156133 Version Self-tuning function： While pressing two buttons for about 8 / S, the system will start the auto-tuning position function, the tuning process takes about 5 minutes. Note When the auto tuning function is activated, the button will automatically fail until the setting is complete.
- Page 8 Note: The display light color reset, the following steps: Note: There are three cases where the red light flashes: Not reached the target position / deviation position 1) loosen the 4 screws until the housing is open; During exercise of the actuator 2) the default sensor plug plastic outward, as shown in the figure Was externally or piped to the valve position 3) Unplug the plug, reinsert it, and plug the metal face outwards.
- Page 9 Despite all this, there is no guarantee that the goods to the destination is intact. So, received the Type 5370 and other items, must be check. If the product is not good, or spare parts not neat, the consignee should be in the shortest possible time (7 days) notify DVC.
- Page 10 4.4.disassembly and assembly Hand rotates counterclockwise, and remove Rotate counterclockwise by hand and remove the transparent cover the transparent cover Remove the rubber position indicator with Remove the four screws with an Allen wrench the appropriate tool 09 / 15...
- Page 11 4.4.1. Connection of the controller to the actuator 4.Type 5370 is connected to the actuator 5.1. 1561 & 156133 Version is connected to the actuator Note: We use a very simple way to connect, only in accordance with the standard...
- Page 12 AC 110V,220V (optional) Electronic component All of the electronic components in the control device of Type 5370 are equipped with built-in pin connectors which avoid unnecessary wiring and interference. According to standard, a PCB could be connected with 3 solenoid valves (V1, V2, V3) at most and with 4 output of position feedback.
- Page 13 4.6.1 PCB PCB-Terminal Features: 1=+24V DC 2=- 24V DC 3=V1 : INPUT PNP 24V 4=S1 : Output PNP 24V 5=S2 : Output PNP 24V 6=A+ : Analog signal output 4-20mA 7=A - : Analog signal output 4-20mA...
- Page 14 The AS-I equipped with PCB could be connected with 4 solenoids and proximity switches at most. 4. 7. 1 . The connecting quantity of Type 5370 unit and the max. length of Bus Circuits Each master controller could be connected with 62 AS-I control units at most (support model A and B).
- Page 15 6. Debugging: reason and solution Problem Reason Solution •To inspect if the circuit of compressed air in valve is opened. Lack of air source •To inspect the supplied pressure. •The flow is not enough. Valve is moved •To inspect the supplied pressure of compressed slowly The valve is not controlled by the air.
- Page 16 8. Technical specification 8. 1. Technical specification Transparent cover cover Bottom seat Actuator P = air inlet R = vent Material Cable Connector Transparent lid 1 = working mouth cover Engineering plastics 2 = working mouth 2 = working mouth Bottom seat Engineering plastics Pneumatic specification...
Need help?
Do you have a question about the 5370 and is the answer not in the manual?
Questions and answers