Download Print this page
Abode Bayenne Bridge 5656 Manual

Abode Bayenne Bridge 5656 Manual

With independent spray

Advertisement

Quick Links

Important Technical Data
Minimum operating pressure 1.0 bar (tap)
Maximum operating pressure 5.5 bar* (tap)
Maximum operating pressure 2.0 bar* (spray)
Maximum hot water temperature 70°C*
Recommended hot water temperature 46°C
Note: If these temperatures or pressures are
exceeded, even for short periods, damage can
result. In these instances a thermostatic mixing or
pressure reducing valve should be installed.
Abode taps use WRAS, KIWA, NSF or recognised
approved components or are manufactured in
accordance with recognised European or
international standards. Please ensure that your
Abode Kitchen mixer is fitted in accordance with
Local Water Byelaws.
These installation guidelines have been prepared
for your direction and you must exercise due care
at all times. We do not accept responsibility for
problems that may occur through improper
installation. Whilst assembling the tap take care
not to accidentally loosen any screwed
assemblies.
Abode is a registered trademark of Abode A
division of Norcros Group (Holdings) Limited
Manufacturers Product Reference
©Abode
11/2017
Unit L, Zenith Park, Whaley Road,
Barnsley,
S75 1HT.
Tel: 01226 283434 Fax: 01226 282434
www.abode.eu
All errors and omissions excepted.
Bayenne Bridge
with independent
spray
5 Year Warranty,
Terms And Conditions
In the unlikely event that you should experience
any defect in the materials or workmanship of
your new Abode mixer within 5 years of
purchase, the purchaser's sole remedy shall be
the replacement (at the manufacturer's
discretion) of all or any part of the product that is
defective. All working parts and valves are
guaranteed for a period of 5 years from
purchase. Decorative surface finishes and O-
rings are guaranteed for 1 year from the date of
purchase provided that our advice concerning
care has been observed and no scouring agents
have been used. This is provided that the mixer
or tap has been used for normal domestic
purposes and that the care, installation and
maintenance instructions have been observed.
The warranty extends to the original purchaser
only.
Marks, scuffs and scratches caused by improper
installation or accidental damage are not
covered by this guarantee. Neither are shade
variations or any damage or defect caused by
incorrect installation or abuse of the fitting.
Please leave these instructions for your customer.
As we are continuously improving and
developing our range of products, finishes &
colours, in the event of a valid claim, we may
not be able to provide an identical replacement
for the defective product throughout the
guarantee period. Where an identical product is
no longer available, we will supply the nearest
equivalent from our then current product range.
In assessing your claim, we must be given the
opportunity to inspect the product as installed
prior to removal. Any product returns must be
packaged as received and complete.
No other warranties, express or implied, are
made, including merchantability or fitness for a
particular purpose. Under no circumstances shall
the manufacturer be liable for any loss or
damage arising from the purchase, use or
inability to use this product, or for any special,
indirect, incidental or consequential damages.
No liability is accepted for consequential
damage to other household fixtures, fittings or
furnishings arising from this claim, even if
attached to the product. No installer, dealer,
agent or employee of Abode has the authority
to modify the obligations or limitations of this
warranty.

Advertisement

loading

Summary of Contents for Abode Bayenne Bridge 5656

  • Page 1 In these instances a thermostatic mixing or pressure reducing valve should be installed. Abode taps use WRAS, KIWA, NSF or recognised approved components or are manufactured in accordance with recognised European or international standards.
  • Page 2 Installation: Parts and Contents: Pass the upper rubber washers (B) onto the inlet legs (C) flush to the tap base (A). Description Pass the inlet legs (C) through the tap holes. Now pass the lower rubber washers (D), metal washers (E) then fixing Mixertap body nuts (F) onto the inlet legs (C).