Advertisement
Operating Suggestions
The low tracking force and high compliance of Audio-Technica
cartridges provide the highest level of performance available, but also
make them susceptible to damage if handled improperly.
Most stylus damage is caused by rough treatment while the tone
arm is being operated by hand. A finger should always be placed
under the tone arm finger lift, never over it. A damped cueing device
that lowers the tone arm gently to the record is found on many record
players, and should be used for greatest protection of the stylus and
records.
The stylus should be cleaned with the brush supplied with the
cartridge. Use a rear-to-front motion of the brush only.
An accumulation of dirt on the stylus indicates that the records
themselves are dirty, a condition which will shorten record and stylus
life, and reduce the potential performance of your system.
Keep records stored vertically in their jackets except when being
played, and clean each side of the record just before it is played. You'll
be amazed at how much better a clean record sounds and how much
longer it lasts.
Replacement Styli
Audio-Technica grain-oriented diamond styli are carefully selected
and polished for minimum wear to themselves and to your records.
However, after an extended period of play, even the finest diamond
stylus becomes worn. For this reason, it is best to have the stylus
inspected annually, or whenever it appears that wear or damage may
be a problem. The dealer from whom you purchased this cartridge can
supply genuine A-T replacement styli. Only A-T styli with the circle
monogram will provide the same level of performance.
Audio-Technica cartridges are protected by the following patents:
Canada Nos. 856,351 and 909,683
England Nos. 1,232,210 and 1,283,404
France No. 6,928,056
Japan Nos. 1,083,037 and 883,307
Sweden No. 347,636
Switzerland Nos. 478,502 and 505,437
U.S.A. Nos. 3,720,796; 3,761,647 and 4,075,418
Germany Nos. 1,772,685 and 1,941,569
Audio-Technica brand products purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc. (A. T .U.S.) to be free of defects in materials and
workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A.T.U.S., or an
Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date. Prior approval from A.T.U.S. is required for return. This warranty excludes defects due to
normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or modification.
For return approval and shipping information, contact the Service Department, Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for any consequential, incidental, or special damages; any warranty of merchantability or fitness
for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
SPECIFICATIONS
Frequency Response (Hz)*
Vertical Tracking Force (VTF)
Range (grams)
Channel Separation
(dB at 1kHz/10kHz)
Channel Balance (dB)
Output (mV at 1kHz, 5 cm/sec)
Vertical Tracking Angle
Stylus Shape
Stylus Construction
Cantilever
Wire Used For Coils
Recommended Load
Impedance (ohms)
Recommended Load
Capacitance (pF)
Dynamic Compliance
(x 10-6 cm/dyne, 100Hz)
Cartridge Weight (grams)
Dimensions
Mounting
Replacement Stylus
*This model exceeds the requirements of DIN Standard 45 500 for frequency
response bandwidth and tolerance.
†
DIN 45 549/AT6607 test records with bands of carefully calibrated recorded
amplitude (one micron equals 0.0001 cm). Program IeveIs of typical commercial
recordings are on the order of 60-70 microns.
††
20˚ is lEC/DIN Standard.
One Year Limited Warranty
AT150MLX
10-30,000
0.75 - 1.75
30/20
0.8
4
††
23˚
MicroLine
Nude square shank
Gold-plated boron
PCOCC
47,000
100 – 200
10.0
8.3
1" x
11
/
" x
16
1
/
" centers
2
ATN150MLX
330/686-2600
P51748
©2005 Audio-Technica U.S., Inc.,
™
11
/
"
16
Printed in U.S.A.
Advertisement
