Table of Contents
Advertisement
Quick Links
1. Product Name
LED Projector
2. Product Code
22611
3. Colour
White
4. Brief Description
Energy-efficient, cool running, quiet and virtually maintenance-free. Integral 40W LED
lamp provides bright, white light and typically lasts 100,000 hours.
5. Contents
1 x LED Projector
1 x 85mm lens (attached)
1 x 12V DC Transformer with 2 metre IEC lead
6. Snoezelen® Stimulations
Sight
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Optikinetics OPTI Solar Sensory LED
Summary of Contents for Optikinetics OPTI Solar Sensory LED
- Page 1 1. Product Name LED Projector 2. Product Code 22611 3. Colour White 4. Brief Description Energy-efficient, cool running, quiet and virtually maintenance-free. Integral 40W LED lamp provides bright, white light and typically lasts 100,000 hours. 5. Contents 1 x LED Projector ...
- Page 2 7. Best Use This product looks most effective in a darkened environment. Projections can be made even more visually striking when used with compatible products. 8. Compatible ROMPA® Products The LED Projector must be used with an accessory in the rear gate, typically a Wheel Rotator: 22613 Wireless Standard Wheel Rotator 22614 Wireless Magnetic Wheel Rotator...
-
Page 3: Detailed Description
10. Detailed Description Energy-efficient, cool running, quiet and virtually maintenance-free. Integral 40W LED lamp provides bright, white light and typically lasts 100,000 hours. Low power consumption. Compatible with accessories and wheels such as the Clip-on Prism. Requires Wireless Wheel Rotator 22614 or 22613. Not compatible with Wheel Rotators 22335, 13170, 16570 and 20685. -
Page 4: Technical Specification
12. Technical Specification Size: 34.7L x 13.3W x 10.2cmD (22.8cm including bracket) Power Rating: 62 Watts maximum Voltage: 220-240V~ or 110-120V~ 50/60Hz 12VDC Output Current: 500mA maximum Light: 40W LED Module Average LED Module life 100,000+ hours Weight: 3.2kg Lumens: 850 lumens (on screen) Colour : Colour temperature 4000°... - Page 5 Consider the following projection distances:...
- Page 6 Use the projector’s bracket to mount the projector in any of the following ways: CAUTION: Never operate the projector in a position where the air vents can be blocked Ensure that the projector is secured to a surface or structure able to bear the weight of the projector and accessories, via the bracket fitted using suitable central bolt (minimum: 14mm M10 x 20mm), washers and attachments.
- Page 7 Place a suitable accessory in the projector e.g. Wireless Wheel Rotator with an Effect Wheel. Slide the Wireless Wheel Rotator (22613 Standard, 22614 Magnetic) into the rear gate runners (the main effect goes into the rear gate runners, with Distortion Wheels etc. in the front gate runners).
- Page 8 Focus the projected image by twisting the lens in and out until the desired focus is achieved. During focusing beware of rotating the projection lens too far out as this can cause the lens to separate from the projector and may drop and break or cause injury. Projector use with external switches ...
-
Page 10: Care And Maintenance
14. Care and Maintenance Always switch the projector off, unplug and allow to cool before moving, storing and before all maintenance e.g. changing a fuse. If storing, wrap the cable loosely around the projector once completely cool. The focusing lens should only be cleaned with a dry cloth, ensuring the fans are free from dust. -
Page 11: Troubleshooting
15. Troubleshooting Problem: The Clip On Prism (or other accessory) will not fit on the front lens of the projector • Check that the ‘click-clack’ has not been removed. This is a cylindrical piece that sits inside the lens (shown below). Check that this is not still attached to the accessory that has previously been removed from the projector.
Need help?
Do you have a question about the OPTI Solar Sensory LED and is the answer not in the manual?
Questions and answers