1. Manuals
  2. Brands
  3. Zepro Manuals
  4. Control Unit
  5. T60
  6. Installation instruction

Zepro T60 Installation Instruction

Radio control unit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Z-LYFTEN PRODUKTION AB
INSTALLATION INSTRUCTION
Försäljning/Sales/Verkauf
Mossvägen 8, 641 49 KATRINEHOLM,SWEDEN
Telephone:
+46 150 - 489550
Telefax:
+46 150 - 489551
E-mail:
zepro@zepro.com
Radio control unit
with angle sensor
Fabrik/Factory/Fabrik
Allévägen 4, 840 73 BISPGÅRDEN, SWEDEN
Telephone:
+46 696 - 17200
Telefax:
+46 696 - 17244
E-mail:
info@zepro.com
Internet:
www.zepro.com
55614TL
2016-10-06

Advertisement

Table of Contents
loading

Summary of Contents for Zepro T60

  • Page 1 2016-10-06 Försäljning/Sales/Verkauf Fabrik/Factory/Fabrik Mossvägen 8, 641 49 KATRINEHOLM,SWEDEN Allévägen 4, 840 73 BISPGÅRDEN, SWEDEN Telephone: +46 150 - 489550 Telephone: +46 696 - 17200 Telefax: +46 150 - 489551 Telefax: +46 696 - 17244 E-mail: zepro@zepro.com E-mail: info@zepro.com Internet: www.zepro.com...

  • Page 3: Table Of Contents

    3. Installation Zepro T60 receiver........... 4. Installation of angle sensor ............5. Electric- and hydraulic diagram ..........6. Zepro T60 - 4 channel radio ............6. Zepro T60 - 8 channel radio ............7. Circuit card, 4 channel radio ............

  • Page 4: Important

    Note! The old Zepro T60 6-channel occurs in 2 versions, a DA and a DC version. If your receiver is a new 8-chan- nel, it´s a DF. One way to check which version that is available, is to remove the cap on the receiver and...

  • Page 5: Installation Of Angle Sensor

    This is to prevent that the tail lift is being used intentionally or unintentionally when the user don’t have control over the working area. Bypass of this function ceases the CE marking from Zepro. See different options of mounting below.

  • Page 6: Electric- And Hydraulic Diagram

    5. Electric- and hydraulic diagram Connection without connection card (ZePro1 controlercard, firmware 8.0 or later.
  • Page 7 5. Electric- and hydraulic diagram Connection of connection card to ZePro1 controlercard Connection card is required when connecting Radio on ZePro1 controler card with firmware 7.0 or earlier.
  • Page 8 5. Electric- and hydraulic diagram Connection on a lift with connection card (Order. no. 55027TL), all controls...
  • Page 9 5. Electric- and hydraulic diagram Connection on a lift with connection card (Order. no. 55027TL), radio only OBS! Bygel på kretskort ska tas bort innan vinkelgivare monteras NOTE! The circuit card jumper must be removed before angle sensor is installed...

  • Page 10: Zepro T60 - 4 Channel Radio

    6. Zepro T60 - 4 channel radio Colour of cable and function. 1. White: Earth (marked with a - minus sign) 2. Black: 12 V DC or 24 V AC/DC (or black marked with a + plus sign) 3. Brown: UP function 4.

  • Page 11: Zepro T60 - 8 Channel Radio

    6. Zepro T60 - 8 channel radio Colour of cable and function 1. White: Earth (marked with - minus) 2. Black: 12 V DC or 24 V AC/DC (marked with a plus sign) 3. Brown: UP function 4. Blue: TILT function 5.

  • Page 12: Circuit Card, 4 Channel Radio

    7. Circuit card - 4 channel radio. Circuit card: explanation 1. Yellow LED indicates correct voltage. 2. Green LED indicates receiving of radio signal. 3. Red LED off = no transmitter programmed. Red LED blinks = transmitter programmed. Red LED shines = receiver in program mode. 4.

  • Page 13: Circuit Card 8 Channel Radio

    7. Circuit card - 8 channel radio. Tele Radio R60 XX V x.x Circuit card: explanation 1. Yellow LED indicates correct voltage. 2. Green LED indicates receiving of radio signal. 3. Red LED off = no transmitter programmed. Red LED blinks = transmitter programmed. Red LED shines = receiver in program mode.

  • Page 14: Programming: New Transmitter To T60 Receiver

    8. Programming: New transmitter to T60 receiver. Applies all 3 / 4 - channel radio and DC / DF varieties of T60 receiver Erase old transmitters Note! All steps below must be carried out 1. Open lid at receiver. 2. Push button on receiver circuit card for programming new transmitter (see page 8 and 9), whereupon red LED (3) shines with a permanent light.
  • Page 15 8. Programming: New transmitter to T60 receiver. Applies DA variety of 6 - channel radio. Erase old transmitters 1. Open lid at receiver. 2. Push-button (12 & 13) at the same time, red LED shines with a permanent light. Keep button down until red LED stops shining.

  • Page 16: Troubleshooting

    9. Troubleshooting. Malfunction Possible cause Correction The receiver does not func- The receiver isn’t properly Check installation of the tion at transmitting. installed. The receiver has receiver. got wrong operating voltage. The green LED no:2 on the The code in the transmit- Contact your dealer.

Table of Contents