Advertisement
2. introduction
Heavy duty 10 tonne high level axle stands. Sturdy welded steel construction for superior safety and strength. large crutch for good load
distribution. Supplied with captive pin support. Suitable for commercial and public service vehicles. Sold in pairs.
3. specification
Model no .............................................................. as10h.v2
Capacity each ..................................... 10 tonnes (10,000 kg)
Capacity Pair ....................................... 20 tonnes (20,000 kg)
minimum Height ......................................................... 795mm
maximum Height ...................................................... 1215mm
4. operation
4.1.
familiarise yourself with the product. Check that the stands are in good condition
and that no damage has been sustained during transit.
4.2.
Insert the centre column (fig.1.1) through the top of the stand.
4.3.
Adjust to height required and insert the locking pin (fig.1.2).
Warning! The pin must be inserted only where shown in fig.1.2.
‰
4.4.
ensure the maximum load does not exceed 20 tonne per pair of axle stands,
(10 tonne for each stand).
4.5.
Refer to vehicle manufacturer's instructions for recommended support points.
Check that the points are in good condition.
4.6.
ensure the vehicle brake is on (or in park mode) and wheels are chocked.
4.7.
Adjust height of stand to correspond with the raised vehicle.
4.8.
Check that the locking pin is correctly pushed all the way through the centre column and out of the other side, as shown in fig.1.2.
4.9.
Position stands under vehicle at points recommended by vehicle manufacturer.
4.10.
Carefully and slowly lower the load onto stands. ensure the load bearing points sit in the center of the stand saddle and check
that the stands are stable and not leaning. Also ensure that there are no objects or persons that could impede the safe lowering of the
vehicle onto the stands.
4.11.
To remove stands jack vehicle slightly so that stand can be removed.
4.12.
After use, hold the centre column (fig.1.1) firmly when removing the locking pin (fig.1.2). Failure to do so will allow the center column
to fall freely through the main center tube which could be dangerous.
Warning! ensure you follow all instructions carefully. failure to note these warnings may cause damage, serious injury or loss of
‰
life.
5. Maintenance
5.1.
Before each use check to ensure stands and stand welds are not cracked, and that there are no missing and/or damaged parts.
Warning! Any stand that appears to be damaged in any way must be removed from service immediately.
‰
5.2.
ensure the locking pins, are in good order and condition.
5.3.
due to the potential hazards associated with these stands, do not misuse, or make any modification to the stands or components.
5.4.
It is the responsibility of the stands owner to ensure the operator has read these instructions, and that the operator is familiar with
the stands use and limitations.
Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
environMent protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
sealey group, Kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar
01284 757500
© Jack Sealey limited
01284 703534
sales@sealey.co.uk
Original Language Version
fig.1
www.sealey.co.uk
AS10H.V2
Issue:6 (4) - 19/12/18
Advertisement
