Advertisement
2. INTRODUCTION
Heavy-duty axle stands to safely support vehicles for extended periods of time. Large crutches for good load distribution. The heavy gauge steel
frame and welded construction gives superior strength and safety. All stands feature captive, multi-position pin load support. Sold in pairs.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AS12
Capacity Each: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 tonnes (12,000 kg)
Capacity Pair: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 tonnes (24,000 kg)
Minimum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485mm
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750mm
4.
OPERATION
1.1.
Familiarise yourself with the product. Check that the stands are in good condition
and that no damaged has been sustained during transit.
1.2.
Ensure the maximum load does not exceed 14 tonne per pair of axle stands, (7 tonnes for each stand).
1.3.
Refer to vehicle manufactures instructions for recommended support points. Check that the points are in good condition.
1.4.
Ensure the vehicle brake is on (or in park mode) and wheels are chocked.
1.5.
Adjust height of stand to correspond with the raised vehicle.
1.6.
Check that the locking pin is correctly pushed all the way through the centre column and out of the other side see fig.1, then position
stands under vehicle at points recommended by vehicle manufacturer.
1.7.
Carefully and slowly lower the load onto stands. Ensure the load bearing points sit in the center of the stand saddle and check that the
stands are stable and not leaning. Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle
onto the stands.
1.8.
To remove stands jack vehicle slightly so that stand can be removed.
1.9.
After use, hold the centre column (fig.1.1) firmly when removing the locking pin (fig.1.3). Failure to do so will allow the center column
to fall freely through the main center tube (fig.1.2) which could be dangerous.
WARNING! Ensure you follow all instructions carefully. Failure to note these warnings may cause damage, serious injury or loss of life.
‰
5. MAINTENANCE
5.1.
Before each use, check that stands and stand welds are not cracked and that there are no missing or damaged parts. Any suspect axle
stands must be removed from service immediately.
5.2.
Owing to the potential hazards associated with stands do not misuse, or make any modification, to the stands or components.
5.3.
It is the responsibility of the owner to ensure that the operator has read these instructions together with the safety features on the side of
the stand and that the operator is familiar with its use and limitations.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal of it according to local regulation
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Environmental Protection
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
fig.1
s.
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
AS12.V2
Issue: 1 - 05/05/17
Advertisement
