1. Manuals
  2. Brands
  3. HOMECARE PRODUCTS Manuals
  4. Lifting Systems
  5. EZ-ACCESS TILT Toilet Incline Lift Corded...
  6. Installation and user manual

HOMECARE PRODUCTS EZ-ACCESS TILT Toilet Incline Lift Corded Power Installation And User Manual

Universal motor mount (left or right side)
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and User Manual
TILT® Toilet Incline Lift – Corded Power
UNIVERSAL MOTOR MOUNT (LEFT OR RIGHT SIDE)
2-YEAR WARRANTY. Please register at www.ezaccess.com/warranty-satisfaction.
© Homecare Products, Inc. All rights reserved. All text and images contained in this document
are proprietary and may not be shared, modified, distributed, reproduced, or reused without the
express written permission of EZ-ACCESS®, a division of Homecare Products, Inc.
Manufactured in the USA
16398 REV 03-06-2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EZ-ACCESS TILT Toilet Incline Lift Corded Power and is the answer not in the manual?

Questions and answers

Related Manuals for HOMECARE PRODUCTS EZ-ACCESS TILT Toilet Incline Lift Corded Power

Summary of Contents for HOMECARE PRODUCTS EZ-ACCESS TILT Toilet Incline Lift Corded Power

  • Page 1 UNIVERSAL MOTOR MOUNT (LEFT OR RIGHT SIDE) 2-YEAR WARRANTY. Please register at www.ezaccess.com/warranty-satisfaction. © Homecare Products, Inc. All rights reserved. All text and images contained in this document are proprietary and may not be shared, modified, distributed, reproduced, or reused without the express written permission of EZ-ACCESS®, a division of Homecare Products, Inc.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ................................2 SYMBOLS AND WARNINGS ............................3 GETTING STARTED, BOX CONTENTS, TOOLS NEEDED, HARDWARE CONTENTS, PRODUCT OVERVIEW ..... 4 SECTION 1: PRE-INSTALLATION ........................... 5 SECTION 2: FRAME INSTALLATION ..........................5 SECTION 3: ACTUATOR MOUNT ..........................6-8 SECTION 4: ACTUATOR DETAIL AND ASSEMBLY ......................

  • Page 3: Symbols And Warnings

    SYMBOLS The WARNING symbol indicates a potentially hazardous condition/situation. The safety warnings throughout this manual, and on your equipment, if any, are for the protection of people and property. Failure by any operator to abide by safety warnings will result in a waiver of all liabilities, loss of your warranty, and could result in equipment damage and or failure, property damage, risk of serious bodily injury, and or death.

  • Page 4: Getting Started, Box Contents, Tools Needed, Hardware Contents, Product Overview

    GETTING STARTED 1. Information in this document is subject to change without notice. The most current version of this manual is available on our website at www.ezaccess.com. 2. Before installation, ensure that there is enough space for proper TILT operation (refer to ‘PRE-INSTALLATION’ section).

  • Page 5: Section 1: Pre-Installation

    PRE-INSTALLATION 1.1 Before installation, ensure there is sufficient space around TILT for proper operation. The TILT frame requires 6” on either side of the toilet bowl and 7-1/2” in front of the bowl (FIG. 1). For illustrative purposes, FIG. 1 shows actuator on left and right sides, your actuator will be mounted on the left or right side.

  • Page 6: Section 3: Actuator Mount

    3. ACTUATOR MOUNT 3.1 Once the frame is properly mounted to the toilet, carefully lift/extend the TILT by pulling the two handles forward and slightly upward (FIG. 4), until the seat is fully raised and slightly overextend (this allows the seat to stay in the “up” position while the actuator and actuator mount are installed).
  • Page 7 3.6 For a left side mount, red alignment dots will be facing outward, away from the bowl (FIG. 8). For a right side mount, green alignment dots will be facing outward (FIG. 9). Actuator images shown are for illustrative purposes only; actual style may vary. LEFT SIDE MOUNT FRONT, INSTALLING VIEW REVERSE VIEW...
  • Page 8 3.7 Place actuator mount ③ over bolt ④ as shown (FIG. 10). 3.8 With your hand on position ⑤, push actuator mount down and guide actuator mount tab ⑥ into the frame bracket ②, until it rests completely inside the frame bracket ②. 3.8.1 At this point, the 2 red alignment dots (green if right side mount) will align, one over top of the other, when actuator mount is in proper position, as shown in (FIG.

  • Page 9: Section 4: Actuator Detail And Assembly

    4. ACTUATOR DETAIL AND ASSEMBLY 4.1 Using the blue dots on actuator bracket ③ and actuator ④ as guides (FIG. 14), hold actuator ① and lower the seat to align the actuator slot with the actuator bracket ②. 4.2 Ensure the actuator bracket rests inside of the actuator slot. 4.3 Once aligned, fully insert the pin into actuator and through the bracket (FIG.

  • Page 10: Section 6: Handheld Control

    6. HANDHELD CONTROL 6.1 The handheld control ships from the factory already plugged into the actuator; no further assembly is required. 6.2 Spend some time to become familiar with the look and feel of the handheld control as well as the location of the control’s directional arrows (FIG.

  • Page 11: Section 8: Cleaning/Sanitization/Maintenance

    8. CLEANING / SANITIZATION / MAINTENANCE 8.1 For hygiene and safety, diligent cleaning, sanitization, and inspection of the TILT is essential and each situation may have unique requirements. For example, multiple users may have different health and sanitization needs than a single user. It is important that an effective cleaning and sanitization schedule be established that fits your situation.

Table of Contents