VALBERG BM 1993 User Manual

VALBERG BM 1993 User Manual

Safety cabinet

Advertisement

Available languages

Available languages

Before you start

The lock can handle two opening codes: Master code and User code 2. The Master code is set from the factory
to 123456. User code 2 is submissive to the Master code and is not included in the Factory settings. The Master
code must be changed before you can program User code 2.
The lock signals with a beep and a flash with every correct action, and it signals with a long beep and red flash
with every wrong action.
Always program the lock with an open door and check the result before you close the door.

Open the lock

1. Push "ON". The lock signals with a beep and the green light comes on.
2. Enter Master code (Factory Master code. 123456) or User code 2. The lock signals with a LED flash.
3. Turn the handle clockwise within 4 seconds.

Open the safe

1. Close the door completely. Make sure nothing gets jammed.
2. Turn the handle anticlockwise.

Change Master code

1. Open the lock.
2. Push "ON" and then "ENTER".
3. Push 1 and then "ENTER".
4. Enter the current Master code and then "ENTER". The lock signals with 2 beeps and LED flashes.
5. Enter a new 6-8-digit code and then "ENTER". The lock signals with 2 beeps and LED flashes.
6. Enter the new 6-8-digit code again and then "ENTER". The lock signals with 2 beeps and LED flashes.

Activate User Code 2

1. Open the lock.
2. Push "ON" and then "ENTER".
3. Push 2 and then "ENTER".
4. Enter the current Master code and then "ENTER". The lock signals with 2 beeps and LED flashes.
5. Enter a new 6-8-digit User code and then "ENTER". The lock signals with 2 beeps and LED flashes.
6. Enter the new 6-8-digit User code again and then "ENTER". The lock signals with 2 beeps and LED flashes.

Change User code 2 without Master code

1. Open the lock.
2. Push "ON" and then "ENTER".
3. Push 3 and then "ENTER".
4. Enter the current Master code and then "ENTER". The lock signals with 2 beeps and LED flashes.
5. Enter a new 6-8-digit User code and then "ENTER". The lock signals with 2 beeps and LED flashes.
6. Enter the new 6-8-digit User code again and then "ENTER". The lock signals with 2 beeps and LED flashes

Delete User code 2

1. Open the lock.
2. Push "ON" and then "ENTER".
3. Push 0 and then "ENTER".
4. Enter the current Master code and then "ENTER". The lock signals with 2 beeps and LED flashes.
USER MANUAL
SAFETY CABINET
BM 1993
See other side, how to change battery
2020-02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BM 1993 and is the answer not in the manual?

Questions and answers

Summary of Contents for VALBERG BM 1993

  • Page 1 USER MANUAL SAFETY CABINET BM 1993 Before you start The lock can handle two opening codes: Master code and User code 2. The Master code is set from the factory to 123456. User code 2 is submissive to the Master code and is not included in the Factory settings. The Master code must be changed before you can program User code 2.
  • Page 2 Changing the battery ➢ When the battery level I slow, the lock indicates this by 5 LED flashes and beeps after you have pushed “ON”. Please change the battery immediately which is located inside the safe on the doors upper side. The required battery is a 9 Volt alkaline (6LR61) ➢...
  • Page 3 BRUKSANVISNING BRANDKLASSADE STÖLDSKYDDSSKÅP BM 1993 Allmänt Låset kan hantera två öppningskoder: Masterkod och kod 2. Masterkoden är inlagd från fabrik och tillfälligt inställd på 123456. Kod 2 är underställd Masterkoden och är ej inlagd från fabrik. Masterkoden måste ändras innan man kan lägga in kod 2.
  • Page 4 Att byta batteri ➢ När batterinivån är låg indikerar låset genom att den röda lampan blinkar 5 gånger, med tillhörande pip efter att ”ON” tryckts in. Byt då genast batteriet som sitter på insidan av dörrens ovansida. Byt till ett alkaliskt 9 volts batteri (6LR61). ➢...

Table of Contents

Save PDF