Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
GAS FIRE PIT
0063
Pin No.:
0063CU7826
Model: P1201 is with glass stones
Model: P1201A is with lava rocks and 4pcs logs
Model: P1201A-L is with 4pcs logs
Model: P1201A-LA is with lava rocks
WARNING: FOR OUTDOOR USE ONLY OR IN AMPLY VENTILATED AREAS
PLEASE KEEP THE MANUAL FOR FUTURE REFERENCE!
0
Advertisement
Table of Contents
Summary of Contents for Ningbo Innopower Hengda Metal Products P1201
- Page 1 GAS FIRE PIT 0063 Pin No.: 0063CU7826 Model: P1201 is with glass stones Model: P1201A is with lava rocks and 4pcs logs Model: P1201A-L is with 4pcs logs Model: P1201A-LA is with lava rocks WARNING: FOR OUTDOOR USE ONLY OR IN AMPLY VENTILATED AREAS...
- Page 2 GAS FIRE PIT SAFETY WARNINGS PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION AND USE. This appliance must be used outdoors or in a well ventilated area and should not be installed or used indoors. To change the gas cylinder in a well ventilated area away from any inflammation sources such as candle, cigarettes, or other flame producing appliances.
-
Page 3: Part List
PART LIST DESCRIPTION Reflector Short bolt Long bolt Top insulation board Glass window bracket A Glass window Glass window bracket B Burner & tank housing assembly M5x12 Screw M5x6 Screw Lava rock or glass stones 4pcs Logs or without ASSEMBLY Instruction before assembly Required Tools: Philip Screwdriver / Adjustable Spanners / Wrenches Leak Detection Solution: one part, detergent and three parts water... - Page 4 Step 1: Open door and take out all inside parts. Please remove out all glass parts slowly and carefully. Step 2: Install the 4pcs Glass window bracket B (#4-4) onto the Burner & tank housing assembly (#5) by using 4pcs M5x12 screws (#6), the bigger screw-hole side on the bottom of bracket B must be subjacent.See illustration 1 Note: The right-angle of bracket B and tank housing assembly must be paralleled during installing Step 3 : Install the 4pcs lower Glass window bracket A (# 4-2) onto the Glass window bracket B (# 4-4) by using...
-
Page 5: Gas Requirements
CAUTION: Glass window is a hot part, don’t touch it while it is working! In case of hotplate glass breakage, shut off all burners and any heating element and isolate the appliance from the power supply. Do not touch the appliance surface. ... -
Page 6: Leak Testing
Tighten all connections firmly and with a spanner where appropriate. The cylinder should be located on the cylinder base. Check for leaks at all joints using soapy water. If a leak is found, tighten the joint and then re-test. SECURING A GAS CYLINDER Position a gas cylinder inside the tank housing. -
Page 7: Important Safety Rules
TO LIGHT THE APPLIANCE The pilot should be lit and the knob set to PILOT. Hold knob depressed gently and turn anti-clockwise to HIGH. When the appliance glows lit, turn knob clockwise from HIGH to LOW as needed. RE-LIGHTING Turn Control Knob to OFF. -
Page 8: Troubleshooting
Gas odor with extreme yellow tipping of flame. The appliance does NOT reach the desired temperature. The appliance glow is excessively uneven. The appliance makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage the appliance and render it unsafe for use. -
Page 9: Technical Data
Blockage in burner blockage and clean burner inside and outside. IN THE EVENT OF ANY PROBLEM, PLEASE ALWAYS CONSULT YOUR LOCAL DEALER TECHNICAL DATA Product Name: Gas fire pit Model No.: P1201, P1201A, P1201A-L, P1201A-LA BE-CY-CH-CZ-FR- BG-HR-CH-CY-DK-EE-FI- Country ES-GB-GR-IE-IT-PT GR-HU-IT-IS-LT-LV-MT-NL-...