Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Raisecom ISCOM RAX711
- Page 1 ISCOM RAX711 (B) Product Description (Rel_01)
- Page 2 Website: http://www.raisecom.com Tel: 8610-82883305 Fax: 8610-82883056 Email: export@raisecom.com Address: Raisecom Building, No. 11, East Area, No. 10 Block, East Xibeiwang Road, Haidian District, Beijing, P.R.China Postal code: 100094 ----------------------------------------------------------------------------------------------------------------------------------------- Notice Copyright © 2014 Raisecom All rights reserved.
- Page 3 Preface Objectives This document describes product orientation, features, networking applications, system structure, OAM, and technical specifications of the ISCOM RAX711. The appendix describes cables and service interface module parameters, and lists terms, acronyms, and abbreviations involved in this document. Versions The following table lists the product versions related to this document.
- Page 4 Raisecom ISCOM RAX711 (B) Product Description Preface General conventions Convention Description Times New Roman Normal paragraphs are in Times New Roman. Arial Paragraphs in Warning, Caution, Notes, and Tip are in Arial. Names of files, directories, folders, and users are in boldface.
-
Page 5: Table Of Contents
Raisecom ISCOM RAX711 (B) Product Description Contents Contents 1 Overview ............................1 1.1 Introduction ..............................1 1.2 Characters ................................. 1 1.3 Features ................................2 1.4 Ordering information............................4 1.4.1 Naming convention ..........................4 1.4.2 Ordering information about device ......................4 1.4.3 Ordering information about auxiliary parts ..................... - Page 6 Raisecom ISCOM RAX711 (B) Product Description Contents 5.4 EMC indexes ..............................29 5.5 Security standards ............................29 5.6 Environmental requirements .......................... 29 5.6.1 Storage environment ..........................29 5.6.2 Transport environment .......................... 31 5.6.3 Operation environment ......................... 33 5.6.4 Biotic environment ..........................33 5.7 Compliant standards and protocols ........................
- Page 7 Figure 2-2 End-to-end ELPS networking ....................... 9 Figure 2-3 Ring network protection application ....................9 Figure 3-1 Appearance of the ISCOM RAX711-CLK ..................10 Figure 3-2 Appearance of the ISCOM RAX711 ....................10 Figure 3-3 AC power interface ..........................14 Figure 3-4 DC power interface ..........................
- Page 8 Raisecom ISCOM RAX711 (B) Product Description Figures Figure 6-5 American standard AC power cable ....................41 Figure 6-6 RJ45 Console cable ..........................42 Figure 6-7 Wiring between PINs on device and PINs on PC ................43 Figure 6-8 LC/PC fiber connector ........................44 Figure 6-9 SC/PC fiber connector ........................
- Page 9 Raisecom ISCOM RAX711 (B) Product Description Tables Tables Table 1-1 Features ..............................2 Table 1-2 Naming convention ..........................4 Table 1-3 Ordering information about device ......................4 Table 1-4 Models and parameters of power modules ..................... 5 Table 3-1 Prints ..............................11 Table 3-2 Service interfaces ..........................
- Page 10 Raisecom ISCOM RAX711 (B) Product Description Tables Table 5-10 Mechanical active substance requirements during operation ............. 34 Table 5-11 Chemical active substance requirements during operation..............34 Table 5-12 Compliant standards and protocols ....................34 Table 6-1 Specifications of the grounding cable ....................39 Table 6-2 Technical specifications of the DC power cable ..................
-
Page 11: Overview
1.1 Introduction The full 1000 Mbit/s Ethernet Demarcation Device (EDD) ISCOM RAX711 (hereinafter referred to as the ISCOM RAX711), developed by Raisecom, is designed for the remote access for the Metropolitan Access Network (MAN), Small and Medium Enterprise (SME) access, and mobile backhaul network access. By cooperating with the ISCOM2924GF- 4GE/4C at the Central Office (CO), it provides a MAN Ethernet access solution that is of easy service activation and deployment for carriers. -
Page 12: Features
Support 1+1 power protection and hybrid input of AC power and DC power. Support EMI Class B. Support Anti-Static Discharge (ASD) interference. 1.3 Features Table 1-1 lists features of the ISCOM RAX711. Table 1-1 Features Feature Description Accessing the device (RJ45 Console/Telnet/SSHv2) Basic features ... - Page 13 Alarm management Hardware monitoring CPU monitoring Caching CPU packets Dual-system Auto-Provisioning Loopback Ping and Traceroute Performance statistics For details about each feature, see ISCOM RAX711 Configuration Guide. Raisecom Technology Co., Ltd.
-
Page 14: Ordering Information
Main feature It supports clock synchronization. Optical modules specified in section 6.2 SFP modules are recommended for the ISCOM RAX711. If you choose other ones, contact Raisecom technical support engineers in advance. 1.4.2 Ordering information about device Table 1-3 lists ordering information about the ISCOM RAX711. -
Page 15: Ordering Information About Auxiliary Parts
Support the SNMP interface and out-of-band network management. Support hybrid power supply of 110/220 VAC and -48 VDC. 1.4.3 Ordering information about auxiliary parts The ISCOM RAX711 can be equipped with the following auxiliary parts: SFP modules Power modules For details about SFP models and parameters, see section 6.2 SFP modules. - Page 16 Raisecom ISCOM RAX711 (B)Product Description Model Description RPA0362-SI-220S12 NEBS-supportive 36 W AC power module Lightning protection level: 6 kV in common mode and 6 kV in differential mode Input voltage range: 100–240 VAC Supported power cables are as below: ...
-
Page 17: Networking Applications
Typical ERPS 2.1 SME access and mobile backhaul networking As shown in Figure 2-1, in MAN access application, as an EDD, the ISCOM RAX711 connects to the ISCOM2924GF-4C in the uplink to implement SME leased line access and mobile backhaul access. -
Page 18: Typical End-To-End Elps Networking
Figure 2-1 SME access and mobile backhaul networking 2.2 Typical end-to-end ELPS networking As shown in Figure 2-2, in the application of connecting the headquarter and the branch, as a remote device, the ISCOM RAX711 reliably connects them. This application has the following features: ... -
Page 19: Typical Erps Networking
ISCOM RAX711 (B)Product Description Figure 2-2 End-to-end ELPS networking 2.3 Typical ERPS networking As shown in Figure 2-3, in MAN access application, as a remote device, the ISCOM RAX711 can network with the ISCOM2924GF-4GE/4C. This application has the following features: ... -
Page 20: System Structure
Raisecom ISCOM RAX711 (B)Product Description System structure This chapter describes system structure of the ISCOM RAX711, including the following sections: Appearance Interfaces LEDs 3.1 Appearance Figure 3-1 Appearance of the ISCOM RAX711-CLK Figure 3-2 Appearance of the ISCOM RAX711 Table 3-1 lists prints on the ISCOM RAX711-CLK. -
Page 21: Interfaces
Service uplink interfaces (SFP) 1000M, LNK/ACT, and UNI Service downlink interfaces (Combo) ESD sensitive symbol 3.2 Interfaces 3.2.1 Service interfaces Table 3-2 lists types and usage of service interfaces on the ISCOM RAX711(-CLK). Table 3-2 Service interfaces Interface Name Type Description 0/1–0/2... -
Page 22: Table 3-3 Parameters Of 100Base-Fx/1000Base-X Sfp Optical Interface
Raisecom ISCOM RAX711 (B)Product Description Interface Name Type Description Combo 10/100/1000BASE-T electrical interface (RJ45) Clock RJ45 Use the E1 cable to transmit clock synchronization synchronization signals. interface 100BASE-FX/1000BASE-X SFP optical interface Table 3-3 lists parameters of the 100BASE-FX/1000BASE-X SFP optical interface. -
Page 23: Management Interfaces
ITU-T Rec, G.703, G.704, G.706, G.732, and G.823 Supported frame format Unframed, Framed, Framed with CRC-4, Multiframe, and Multiframe with CRC-4 3.2.2 Management interfaces Table 3-6 lists management interfaces on the ISCOM RAX711. Table 3-6 Management interfaces Interface Name Type... -
Page 24: Power Interfaces
Electrical feature RS-232 Baud rate 9600 Baud Cable specification 8-core cable 3.2.3 Power interfaces Table 3-9 lists power interfaces on the ISCOM RAX711. Table 3-9 Power interfaces Power interface Print Name AC power interface (100-240V) AC power input interface DC power interface (-48V ) -
Page 25: Leds
Value DC power Rated input voltage -48 VDC module Voltage range -36 to -72 VDC Maximum input current 3.3 LEDs Table 3-12 lists LEDs on the ISCOM RAX711. Table 3-12 LEDs Status Description LNK/ACT Green Link working LED (0/1–1/4) ... -
Page 26: Hardware Logic Structure
Green: LOS occurs on the clock signal input interface or the interface is disconnected. Off: no LOS occurs on the clock signal input interface. 3.4 Hardware logic structure Table 3-6 shows the hardware logical structure of the ISCOM RAX711. Raisecom Technology Co., Ltd. -
Page 27: Figure 3-5 Hardware Logical Structure
Raisecom ISCOM RAX711 (B)Product Description Figure 3-5 Hardware logical structure In terms of hardware, the ISCOM RAX711 is composed of the main control card, control unit, switch unit, port unit, power supply module, and so on. Main control card The main control card has the following functions: ... - Page 28 Raisecom ISCOM RAX711 (B)Product Description Power unit The power unit supports AC power input and DC power input. It supplies power to the entire system. It supports hybrid DC/AC power and hot swapping. Raisecom Technology Co., Ltd.
-
Page 29: Device Installation
(ESD) wrist in good contact with skin and with the plug inserted into the ESD hole of the ISCOM RAX711. High voltage safety When the ISCOM RAX711 is powered on, DO NOT install or dismantle it to avoid unpredictable injury. Raisecom Technology Co., Ltd. -
Page 30: Preparing For Installation
Maximum power consumption 18 W Grounding conditions The ISCOM RAX711 is suitable for installation at both CBN and IBN, and the grounding resistance should be below 1 Ω. Well grounding is the first guarantee to lightning protection and anti-interference. 4.2.3 Installing device The installation mode for the ISCOM RAX711 series is identical. -
Page 31: Figure 4-1 Installing Customized Brackets
Figure 4-3. Figure 4-3 Installing long wall-mount brackets Step 2 Drill four holes on the wall properly, and fix the ISCOM RAX711 vertically on the wall, as shown in Figure 4-4. -
Page 32: Connecting Cables
Step 1 Lay the device stably on the workbench, as shown in Figure 4-5. Figure 4-5 Installing device on workbench Laying heavy objects on the ISCOM RAX711 or covering it with objects is prohibited. 4.2.4 Connecting cables To connect the Ethernet interface or SNMP interface, use the shielded Ethernet cable, and ensure good grounding at both ends. -
Page 33: Figure 4-6 Connecting Grounding Cable
Installing DC power cable Install the DC power cable as below: Step 1 Ensure that the ISCOM RAX711 is well grounded. Step 2 Insert the 3-PIN phoenix connector into the DC power interface on the front panel tightly. Step 3 Insert the stripping end of the DC power cable into the 3-PIN phoenix connector, and fasten the spring screws on two sides of the 3-PIN phoenix connector, as shown in Figure 4-7. -
Page 34: Figure 4-8 Connecting Ac Power Cable
Connect fiber as below: Step 1 Remove the dustproof cover from the SFP optical interface and SFP optical module, and insert the SFP optical module into the optical interface on the ISCOM RAX711, as shown in Figure 4-10. Raisecom Technology Co., Ltd. -
Page 35: Figure 4-10 Inserting Sfp Optical Module
Figure 4-11 Connecting fiber When the optical interface is idle, cover it with the dustproof cover to prevent dust and dirt from entering it and causing the ISCOM RAX711 to work improperly. Connecting Ethernet cable Connect the Ethernet cable as below: Step 1 Choose a proper length for the Ethernet cable according to cabling path, and make an Ethernet cable accordingly. -
Page 36: Installing Software
Step 1 Choose a proper length for the clock cable according to cabling path, and make a clock cable accordingly. Step 2 Insert the RJ45 connector of the clock cable into the clock interface of the ISCOM RAX711, and insert the other RJ45 connector of the clock cable into the clock interface of the peer device, as shown in Figure 4-12. -
Page 37: Technical Specifications
Security standards Environmental requirements Compliant standards and protocols 5.1 Integrated machine parameters Table 5-1 lists integrated machine parameters of the ISCOM RAX711. Table 5-1 Integrated machine parameters Parameter Value Dimensions (mm) 200 (Width) × 180 (Depth) × 43.6 (Height) Dimensions (inch) 7.87 (Width) ×... -
Page 38: Laser Security Class
5.2 Laser security class According to the Tx power of Laser, the ISCOM RAX711 laser belongs to Class 1 in security class. In Class 1, the maximum Tx power on the optical interface is smaller than 10 dBm (10 mW). -
Page 39: Emc Indexes
< 2 hours MTBF 100000 hours 5.4 EMC indexes The ISCOM RAX711, designed according to FCC PART 15 and ETS 300 386 series of European Telecommunication Standards Institute (ETSI), has passed Electromagnetic Compatibility (EMC) tests. NEBS GR-1089-CORE: Network Equipment-Building System (NEBS) Requirements: Physical Protection. -
Page 40: Table 5-3 Atmosphere Requirements For Device During Storage
Reproduction of fungus and mould Existence of rodent animals such as rats Air cleanliness No explosive, conductive, magnetic, and corrosive dust is around the ISCOM RAX711 during storage. Table 5-4 lists mechanical active substance requirements for the ISCOM RAX711 during storage. -
Page 41: Transport Environment
ISCOM RAX711 (B)Product Description ≤ 20.0 Droppable dust (mg/m² · h) ≤ 300 Grit (mg/m³ ) Table 5-5 lists chemical active substance requirements for the ISCOM RAX711 during storage. Table 5-5 Chemical active substance requirements during storage Chemical active substance Value ≤... -
Page 42: Table 5-7 Mechanical Active Substance Requirements During Transportation
Reproduction of fungus and mould Existence of rodent animals such as rats Air cleanliness No explosive, conductive, magnetic, and corrosive dust is around the ISCOM RAX711 during transportation. Table 5-7 lists mechanical active substance requirements for the ISCOM RAX711 during transportation. -
Page 43: Operation Environment
ISCOM RAX711 (B)Product Description 5.6.3 Operation environment Atmosphere environment Table 5-9 lists atmosphere requirements for the ISCOM RAX711 during operation. The temperate and humidity referred to are measured 1.5 m above or 0.4 m in front of the ISCOM RAX711. -
Page 44: Compliant Standards And Protocols
Raisecom ISCOM RAX711 (B)Product Description Air cleanliness No explosive, conductive, magnetic, and corrosive dust is around the ISCOM RAX711 during transportation. Table 5-10 lists mechanical active substance requirements for the ISCOM RAX711 during operation. Table 5-10 Mechanical active substance requirements during operation... - Page 45 Raisecom ISCOM RAX711 (B)Product Description Standard Description MEF9 Abstract Test Suite for Ethernet Services at the UNI MEF10.1 Ethernet Services Attributes Phase 2 MEF11 User Network Interface (UNI) Requirements and Framework MEF13 User Network Interface (UNI) Type 1 Implementation Agreement...
- Page 46 Raisecom ISCOM RAX711 (B)Product Description Standard Description IEEE 802.3ah Ethernet in the First Mile IEEE 802.3x Flow Control IEEE 802.3af DTE Power via MDI (15.4W) IEEE 802.3at DTE Power Enhancements (30W) IEEE 802.3ac VLAN TAG IEEE 802.3an 10GBASE-T IEEE 802.3ae...
- Page 47 Raisecom ISCOM RAX711 (B)Product Description Standard Description MEF9 Abstract Test Suite for Ethernet Services at the UNI MEF14 Abstract Test Suite for Traffic Management Phase 1 MEF16 Ethernet Local Management Interface (E-LMI) MEF20 User Network Interface (UNI) Type 2 Implementation Agreement MEF CE 2.0...
-
Page 48: Appendix
Acronyms and abbreviations 6.1 Cables 6.1.1 Grounding cable Introduction The grounding cable is used to connect the ISCOM RAX711 to the ground. Appearance The grounding cable is composed of OT terminals and the coaxial cable, as shown in Figure 6-1. -
Page 49: Dc Power Cable
6.1.2 DC power cable Introduction The DC power cable transmits -48 VDC power to the power interface of the ISCOM RAX711, and supplies power for the whole device. Appearance The DC power cable is composed of DC connectors and conducting wire, as shown in Figure 6-2. -
Page 50: Ac Power Cables
The AC power cable transmits 110/220 VAC power to the power interface of the ISCOM RAX711, and supplies power for the whole device. The ISCOM RAX711 uses different AC power cables in different countries or regions, as lists in Table 6-3. -
Page 51: Figure 6-5 American Standard Ac Power Cable
Raisecom ISCOM RAX711 (B)Product Description Figure 6-5 American standard AC power cable Technical specifications Table 6-4 lists specifications of the British standard AC power cable. Table 6-4 Specifications of British standard AC power cable Item Description Name POL-AC-British standard 3-pin/plum blossom tail-0.75mm 1.5m/RoHS... -
Page 52: Console Cable
Raisecom ISCOM RAX711 (B)Product Description 6.1.4 Console cable Introduction With the Console cable, you can log in to the ISCOM RAX711 through the Console interface. Appearance Figure 6-6 shows the RJ45 Console cable. Figure 6-6 RJ45 Console cable Technical specifications Table 6-7 lists technical specifications of the Console cable. -
Page 53: Fiber
PIN 9 – – PIN 5 Figure 6-7 shows the wiring between PINs on the ISCOM RAX711 and PINs on the PC. Figure 6-7 Wiring between PINs on device and PINs on PC 6.1.5 Fiber Introduction The ISCOM RAX711 supports single-mode and multi-mode fiber. -
Page 54: Figure 6-8 Lc/Pc Fiber Connector
Raisecom ISCOM RAX711 (B)Product Description Choose the fiber connector properly as required on site. Appearance Figure 6-8 shows the LC/PC fiber connector. Figure 6-8 LC/PC fiber connector When connecting or removing the LC/PC optical connector, align the connector with the optical interface, and do not rotate the fiber. -
Page 55: Ethernet Cable
The Ethernet electrical interface and other devices The SNMP interface and the NMS The Ethernet interface on the ISCOM RAX711 is self-adaptive to straight-through cable mode and crossover cable mode. Make Ethernet cables as required on site. Appearance Figure 6-11 shows the Ethernet cable. -
Page 56: Table 6-11 Wiring Of Eia/Tia 568A And Eia/Tia 568B Standards
PIN 7 White/Brown White/Brown PIN 8 Brown Brown Raisecom provides straight-through cables and 100 Mbit/s crossover cables which are different in name only. Table 6-12 lists technical specifications of the Ethernet cable. Table 6-12 Technical specifications of Ethernet cable Item Description ... -
Page 57: Figure 6-12 Wiring Of Straight-Through Cable
Raisecom ISCOM RAX711 (B)Product Description Figure 6-12 Wiring of straight-through cable The wiring of the 100 Mbit/s crossover cable is different from that of the 1000 Mbit/s crossover cable. One RJ45 connector of the crossover cable follows EIA/TIA 568A standard wiring; the other RJ45 connector follows EIA/TIA 568B standard wiring. -
Page 58: Clock Cable
Figure 6-14 Wiring of 1000 Mbit/s crossover cable 6.1.7 Clock cable Introduction The ISCOM RAX711 adopts the RJ45 clock interface for inputting and outputting 2 Mbit/s or MHz clock signals. Appearance Figure 6-15 shows the clock cable for the 2 Mbit/s or MHz interface. -
Page 59: Sfp Modules
Raisecom ISCOM RAX711 (B)Product Description Item Description Model Symmetric twisted pair cable-100ohm-enhanced Cat 5 cable- 0.52mm-24AWG-8PIN Number of cores Table 6-14 lists PINs definitions of the clock cable for the 2 Mbit/s or MHz interface for the ISCOM RAX711. Table 6-14 PINs definitions of clock cable for 2 Mbit/s or MHz interface... -
Page 60: Sfp Electrical Module
Raisecom ISCOM RAX711 (B)Product Description Model Wavelength Minimum Extinction Transmission (nm) (Laser type optical overload ratio (dB) sensitivity distance (km) type) power point (dBm) (dBm) (dBm) USFP- 1550 (DFB) -5 to 0 03/S3-D-R USFP- TX1310/RX1 -15 to - 03/SS13- 550 (FP/DFB) -
Page 61: Table 6-17 Parameters Of 1000Base-X Sfp Optical Module
Raisecom ISCOM RAX711 (B)Product Description Table 6-17 Parameters of 1000BASE-X SFP optical module Model Wavelength Minimum Extinction Transmission (nm) (laser type optical overload ratio (dB) sensitivity distance (km) type) power point (dBm) (dBm) (dBm) USFP- 850 (VCSEL) -10 to - 0.55... -
Page 62: Sfp Electrical Module
Raisecom ISCOM RAX711 (B)Product Description Model Wavelength Minimum Extinction Transmission (nm) (laser type optical overload ratio (dB) sensitivity distance (km) type) power point (dBm) (dBm) (dBm) USFP- TX1550/RX1 -3 to 2 Gb/SS35- 490 (DFB) 6.2.4 SFP electrical module Table 6-18 lists parameters of the SFP electrical module. -
Page 63: Acronyms And Abbreviations
Raisecom ISCOM RAX711 (B)Product Description QinQ (also called Stacked VLAN or Double VLAN) technology is an extension of 802.1Q, which is defined in the 802.1ad standard defined by the IEEE. Basic QinQ is a simple Layer 2 VPN tunnel technology. At the ISP's access end, QinQ... - Page 64 Raisecom ISCOM RAX711 (B)Product Description GARP Generic Attribute Registration Protocol Global Positioning System Global System for Mobile Communications GVRP GARP VLAN Registration Protocol IEEE Institute of Electrical and Electronics Engineers IETF Internet Engineering Task Force Internet Protocol International Telecommunications Union -...
- Page 65 Raisecom ISCOM RAX711 (B)Product Description MTTR Mean Time To Restoration Network Node Management Operation, Administration, and Maintenance Personal Computer Quality of Service RADIUS Remote Authentication Dial In User Service RMON Remote Network Monitoring RMEP Remote Maintenance association End Point Radio Network Controller...
- Page 66 Raisecom ISCOM RAX711 (B)Product Description TFTP Trivial File Transfer Protocol Type, Length, Value Type of Service UART Universal Asynchronous Receiver/Transmitter VLAN Virtual Local Area Network Weight Round Robin Raisecom Technology Co., Ltd.
- Page 67 Address Raisecom Building, No. 11, East Area, No. 10 Block, East Xibeiwang Road, Haidian District, Beijing, P.R.China Postal code: 100094 Tel: +86-10-82883305 Fax: 8610-82883056 http://www.raisecom.com Email: export@raisecom.com...