Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Romer II Series
- Page 1 ® “Making the World’s Food Safer” Romer Series II Mill Manual Version: SIIMM01.3 30 November, 2001 ® Romer Labs, Inc. 1301 Stylemaster Drive Union, MO 63084-1156 Fax: (636) 583 6553 Tel: (636) 583 8600 www.romerlabs.com sales@romerlabs.com Toll free: (800) 769 1380...
-
Page 2: Table Of Contents
® Romer Labs, Inc. Romer Labs, Inc. Table of Contents Introduction............................ 3 Safety Information ........................4 Romer Series II™ Mill Protection Guidelines................5 Operation and Grinding Procedure ................... 6 Grinder Knob Adjustments......................6 Cleaning and Care ........................7 Specifications ..........................8 Sampling Procedures ........................ -
Page 3: Introduction
Labs, Inc. Series II™ Mill (U.S. Patent #4,679,737). The Romer Series II™ Mill is a versatile and easy to use mill that will meet your sample preparation and sample grinding needs for a variety of analyses. This mill is designed to grind and sub-sample human foods, animal feeds and feed ingredients. -
Page 4: Safety Information
Romer Labs, Inc. Safety Information Safety should always be the first concern when operating the Romer Series II™ Mill. The following guidelines have been written for your protection. Always use caution when operating any piece of equipment. To avoid personal injury: •... -
Page 5: Romer Series Ii™ Mill Protection Guidelines
The Romer Series II™ Mill is provided with a breaker switch on the back of the motor cover. If the motor becomes too hot, the breaker switch will release and the motor will stop. -
Page 6: Operation And Grinding Procedure
To grind high fat or high moisture products, it may be necessary to adjust the grinder cap to a coarse grind setting. ® The Romer Series II™ Mill has been preset at Romer Labs, Inc., but over time, the burr set (grinding assembly inside the grinder housing) may become worn and need adjustment. To adjust the burr set, follow the procedure listed below. -
Page 7: Cleaning And Care
To fully clean the burr set, turn the power switch to the “off” position and unplug the unit. Remove the grinding assembly by following the steps in “Romer Series II™ Mill Protection Guidelines” that detail how to replace the shear pin. Periodically check the burr set and inside the grinder housing to remove any built-up residue. -
Page 8: Specifications
ROMER ® ® Romer Labs, Inc. Romer Labs, Inc. Specifications Grinding Burrs: Nihard Metal Alloy Grinder Housing: Cast Aluminum Feedworm: Cast Iron Shear Drive: Stainless Steel with black oxide finish Current: AC only Height: 26¾” Voltage (AC:) 115V or 230V Width: 11¼”... -
Page 9: Sampling Procedures
® ® Please consult your Romer Labs, Inc representative for a copy of the Romer Labs, Inc. Guide to Mycotoxins, Volume 2 entitled “Sampling and Sample Preparation for Mycotoxin Analysis” This publication outlines the proper procedures for sampling and sample preparation. - Page 10 ROMER ® ® Romer Labs, Inc. Romer Labs, Inc. bin separately and potentially less moist material from the center of the bin. Transfer the edges-sample and the center-sample to two separate sample bags, close securely and store under dry, cool conditions until analyzed. Label the one sample as "Storage Bin Edges"...
- Page 11 ROMER ® ® Romer Labs, Inc. Romer Labs, Inc. Figure 3 – Flat –bottom trucks or trailers 7-Probe Pattern 9-Probe Pattern Figure 4 – Hopper Cars Figure 5 – Lift-top Barges Page 11 of 17...
- Page 12 ROMER ® ® Romer Labs, Inc. Romer Labs, Inc. Figure 6 – Storage Bin: Feed or Meal: 5 – Probe Pattern Whole Grain: 9 – Probe Pattern Figure 7 – Storage Bin (Moisture Accumulation) Page 12 of 17...
-
Page 13: Technical Service Guide
Thrust plug is chipped or missing. Replace thrust plug. Burrs make grinding noise while running Adjust burr set. with no sample in the mill. ® If you have questions concerning the mill, please contact Romer Labs, Inc at: 1-800-769-1380 or 636-583-8600 Page 13 of 17... -
Page 14: Replacement Parts
Breaker, 10 Amp. EQMMP2010 Thrust plug (pkg. of 5) EQMMP2260 Tension springs (pkg. of 3) EQMMP2250 Exploded diagram of the Romer Series II™ Mill assembly: FACE PLATE HOPPER STAND UNIT WITH MOTOR Page 14 of 17... -
Page 15: Warranty
All liability of Romer Labs, Inc. is limited to the repair or replacement of the mill. Under no circumstances is Romer Labs, Inc. liable for consequential damage or loss. Instruments and accessories subjected to misuse, abuse, neglect, modification or unauthorized repair constitute exclusion from warranty. -
Page 16: Fax Order Form
Federal Express, Account #: Signature: ............Item Number Description Quantity Unit Price (US$) ® For Romer Labs, Inc. shipping dept. only Date shipped: Invoice #: UPS tracking numbers Shipping Charge: Credit card authorization #: Ref #: Batch#: Page 16 of 17... -
Page 17: Routine Maintenance Log
ROMER Routine Maintenance/ Cleaning Log for the Romer Series II™ Mill Romer Labs, Inc ® Date Initials Cleaning Method Problem Repair or Maintenance Done Method #1- Vacuum chutes for 30 seconds per “Cleaning and Care” section of the manual Method #2- Run 50g of next sample through, prior to grinding sub-sample per “Cleaning and Care” section of the manual...
Need help?
Do you have a question about the II Series and is the answer not in the manual?
Questions and answers