Summary of Contents for Magneti Marelli EMS Link
- Page 1 EMS Link EMS Link—Installation and Comm. Line CAN1L CAN Bus low User Manual Power BAT+ KL30 permanent power EMS Link This file is in Glasscubes or ask through e-mail, download in your computer and via USB cable put the file in your android phone , If the App doesn't open, go to settings and unlock it.
- Page 2 5. Restart your android phone and remove the usb cable. 6. Go to settings, other settings, security and privacy, allow unknown sources. 7. Search in the phone storage the Magneti Marelli file, open it. 8. Install the Magneti Marelli EMS link app.
-
Page 3: Table Of Contents
3.2 Step of use ........................... 05 3.2.1 Connection between the smart phone and vehicle ............05 3.2.2 Operation of vehicle ..................... 05 3.2.3 How to use EMS Link APP ..................05 3.3 Note ............................. 12 4 Feature description ........................13 4.1 DashBoard ........................... -
Page 4: Requirement Of Your Smart Phone
1 Requirement of your smart phone For android system, the OS of smart phone must be 4.2 and above; for IOS, the OS of Only Android Phone smart phone must be 7.0 and above 2 Connector information Figure 1 is Dongle OBDII connector (male). figure 1 Table 1 is pinout of OBDII connector. - Page 5 Comm. Line CAN1L CAN Bus low Power BAT+ KL30 permanent power...
-
Page 6: Installation And Step Of Use
Insert the key to the vehicle, and make sure the vehicle‟s status is “key on”. If you need to test dynamic data, please crank the vehicle 3.2.3 How to use EMS Link APP Note: The distance between the smart phone and Dongle must be within 5 meters. Make... - Page 7 3 (2) After clicking „‟EMS Link”, you will enter the “Take A Look” page, as shown in figure 4. In this page, you can slip picture to learn how to use APP. Click the “Skip” button, you will enter the “welcome”...
- Page 8 (3) The “welcome” page is shown in figure 5. Click the “Introduction” button, you will open the user manual; click “Take A Look” button, you will learn how to use app briefly; click the “Go” button, you will enter the “Main” page. figure 5 (4) When you are in main interface, the APP will scan the available devices automatically, as shown in figure 6...
- Page 9 (5) when scanning finished, the APP will list all available devices to user, and the user can click the name of device to connect, as shown in figure 7 figure 7 (6) If the dongle is connected successfully, the “Connect” will become “Disconnect”, as shown in figure 8 figure 8...
- Page 10 (7) Click the “Settings” button to enter the “Settings” page, as shown in figure 9 figure 9 (8) In “Settings” page you can select the language, click “Language” button, you will see the “Chinese” and “English”, you can select either one, as shown in figure 10 figure 10...
- Page 11 (9) In “Settings” page, click the “Bluetooth Device” to clear the paired device, as shown in figure 11 figure 11 (10) In “Setting” page, you can select the “important parameters” which will be shown in “Dashboard”. Click the “Important Parameters” to select. The “Engine RPM” and “Vehicle Speed”...
- Page 12 (11) In “Setting” page, you can select the “other parameters” which will be shown in “Dashboard”. Click the “Other Parameters” to select, as shown in figure 13 figure 13 (12) Click the “Back” button on Smart Phone or Tablet, you will go back to the “Main” page, as shown in figure 14 figure 14 Note: to perform diagnostic features, you have to establish the connection by pushing the...
-
Page 13: Note
1 One dongle only can be connected with one smart phone at the same time 2 If you want to use other smart phone to connect dongle, please kill the running EMS Link APP in the running smart phone, as shown in figure 15... -
Page 14: Feature Description
4 Feature description The EMS Link APP includes “Dashboard” function, “Trip meter” function, “Service Tool” function, “Reflashing” function and “Scan Tool” function, as shown in figure 16 figure 16 4.1 DashBoard The “DashBoard” function can display real-time parameters such as “RPM”, “SPEED”, “Manifold Pressure”, “Battery Voltage”, “Gear Position”, “Water Temperature”, “Air... -
Page 15: Trip Meter
The “other parameters” which is selected in “Other Parameters” page will be shown in “Information” page, as shown in figure 18 figure 18 4.2 Trip Meter The “Trip Meter” function through the GPS to display the “Max Speed”, “Acceleration”, “Altitude” and the “Speed” on your trip. The “Trip Meter” function need to enable the GPS function, as shown in figure 19 figure 19... -
Page 16: Service Tool
4.3 Service Tool “Service Tool” can do the diagnostic function for your vehicle, it includes several modules, as shown in figure 20 figure 20 （ 1 ） Read Data The “Read Data” function is used to read the system parameter, as shown in figure 21. Click “Start”... - Page 17 The test result of “Read Data” function is shown in figure 22 figure 22 （ 2 ） Configure Data The “Configure Data” function is used to read the configuration information, such as ECU version. Click “Start” button and “Search” icon to read data, as shown in figure 23 figure 23...
- Page 18 （ 3 ） Actuator Control The “Actuator Control” function sends the command to test the actuator of the vehicle, as shown in figure 24 figure 24 The test result of “Actuator Control” is shown in figure 25 figure 25...
- Page 19 （ 4 ） Monitor Mode The “Monitor Mode” allow the users to edit the command to test the vehicle, as shown in figure 26 figure 26 You can edit the command in edit box, and click the “Send” button to send the command, the test result of “Monitor Mode”...
-
Page 20: Reflashing
（ 5 ） DTC Management The “DTC Management” function is used to read the DTC, and you can clear the DTC by it, as shown in figure 28. Click the “Start” button to scan DTC, click the “Clear” button to clear DTC. - Page 21 The .bin file and .cks file which will be downloaded into ECU should be stored in the same folder on the smart phone. Click “Select” button to select the .bin file, as shown in figure figure 30 After selecting the correct .bin file, click the “Reflash” button to start, as shown in figure figure 31...
-
Page 22: Scan Tool
Figure 32 shows the “Reflashing” is successful. figure 32 4.5 Scan Tool The “Scan Tool” function read data and perform diagnostic function for OBD II protocol 4.6 Log In/Upload Data/Download In “Main” page, click the “Log in” button to sign in (if you have registered before) or sign up (if have not registered before), as shown in figure 33 and figure 34 By this function you can send/upload diagnostic data to the server or receive/download new engine control software code for the ECU (need to get the access authorization on the... - Page 23 figure 33 figure 34...
-
Page 24: Contact Us
when you log in successfully, you can upload ECU data in “Settings” page, as shown in figure 35 figure 35 Contact us Please contact the following email address if you meet any question Email: ems-link.support@magnetimarelli.com...