Summary of Contents for Oceanled EYES HD GEN2
- Page 1 2020 INSTALLATION & OPERATION MANUAL EYES HD GEN2 OCEAN CAMERA L I G H T. Y E A R S A H E A D . WWW.OCEANLED.COM OceanLED MANUAL / EYES CAMERA / EYES HD GEN 2 / REVISION 1...
- Page 2 READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL WARNINGS Before installing your OceanLED Eyes Camera, please read and follow all warning notices and instructions which are included. Failure to follow safety warnings and instructions can result in property damage, severe injury or even death.
-
Page 3: Table Of Contents
Attention Installer: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner and/ or operator of this equipment. WARRANTY COVERAGE 2-year warranty from time of purchase, regardless of installation date. Please refer to www.oceanled.com/downloads for full warranty statement. -
Page 4: Overview
The power wiring to the camera must be fused. Power Consumption and Recommended Fuse value 15% Reserve Recommended fuse Model Current @ 12V DC Current @ 24V DC Power (W) 12V/24V DC Eyes HD Gen2 100mA 60mA 2.3W 500mA... -
Page 5: Preparing The Hull
OceanLED recommends using a qualified installer / technician when making modifications to your vessel. Please also consult the manufacturer for more detail on modifications and installation. If camera is to be installed in a conductive hull, an Isolation Kit must be used. Contact OceanLED for additional details. -
Page 6: Installation
Suitable video monitor / display unit. Optional Eyes IP68 Camera Connector Enclosure (p/n 019908) OceanLED recommends dry fitting all products. When installing, be sure that the camera fits the area and secures to the hull using the appropriate hardware before applying any sealant. - Page 7 EYES HD GEN2 2020 INSTALL & OPERATION MANUAL 3.2 INSTALLATION (ONCE HULL PREPARATION IS COMPLETE) 1. Test camera before fitting. 2. If using Isolation Kit (Delrin sleeve): Insert the Isolation Kit front washer into the drilled hole and apply marine sealant to seal between the rear of the front washer and the hull.
- Page 8 EYES HD GEN2 2020 INSTALL & OPERATION MANUAL 5. Ensure the camera orientation is correct with the red arrow sticker on the front bezel pointing up perpendicular to the waterline. The arrow points to the top of the image when viewed on a monitor. 6.
- Page 9 EYES HD GEN2 2020 INSTALL & OPERATION MANUAL 9. Connect the bonding cable to the bonding screw on the rear of the camera body. Lock in place with the screw and shake proof washer provided. BONDING: The camera body MUST be attached to the vessels bonding / cathodic protection system.
- Page 10 Cable Always consult a qualified electrician when connecting OceanLED cameras Please note that all OceanLED camera units operate within a specific voltage range. Please check the electrical information to ensure cable gauge follow the recommendations. All connections MUST be enclosed inside a waterproof housing / junction box.
- Page 11 At this final stage make sure all of the system is operational. If you have any issues, please contact your local OceanLED representative. Never install a new camera then leave the vessel in the water unchecked for several days.
-
Page 12: Operation / Maintenance
Marine growth can build up quickly on the camera lens and can reduce the performance in just a few weeks. To help prevent this, all OceanLED Eyes Cameras have been coated with a specialized Tritonium® coating which makes the surface of the glass lens a non-stick layer. Lenses should be cleaned with a boat brush or similar biweekly, or as needed to keep the lens of the camera clean. -
Page 13: Troubleshooting
Ensure the lens is clean, dirty lens can obscure the camera light sensor and cause it to switch to night vision mode. If the camera still shows in B&W despite the correct light level, please contact the OceanLED technical support. -
Page 14: Appendix
Perform this bonding check after installation of the light and before moving the vessel back into the water. Refer to bonding information in the installation sections in this manual. If in doubt, please contact OceanLED. 1. Connect the camera assembly to the cathodic protection system as explained in Chapter 3. -
Page 15: Warranty
HD GEN2 2020 INSTALL & OPERATION MANUAL Warranty Please remove this page and keep for your files For technical assistance: Europe: service@oceanled.com The Americas: warranty@oceanledusa.com Warranty Serial Code(s): © 2020 Ocean LED Marine LTD Ocean LED Marine LTD Ocean LED USA LLC...