Table of Contents
Summary of Contents for Guardian G600-B
- Page 1 DESIGN, INSTALLATION, OPERATION, INSPECTION MAINTENANCE MANUAL MODEL G600-B RESIDENTIAL RANGE TOP EXTINGUISHER UNIT UL FILE NO. EX 3940 APRIL, 2016 (REV 0) 8701 John Carpenter Freeway Suite 230 Dallas, TX 75247 P/N G610B Permit Number: 20-04649...
-
Page 2: Table Of Contents
Guardian Safety Solutions International, Inc. is not liable or responsible ILLUSTRATIONS for clean up or damages incurred due to a discharge. -
Page 3: Figure
(i.e., electrical Wire, wire mold, shut-off components, etc.). Additional equipment and components may be obtained from a Guardian Safety Solutions International distributor or the manufacturer... -
Page 4: Figure
P/N G610B Page 3 April, 2016 (Rev 0) GUARDIAN G600-B SYSTEM COMPONENTS Each system consists of a pre-assembled enclosure extinguisher assembly, sensor assembly, and distribution/nozzle assembly and one (1) shutoff for electrical or gas stoves, ready for installation in the kitchen cabinet and range hood over the stove. -
Page 5: Figure
HIGH (See FIGURE 2) CONCENTRATIONS. AVOID CONTACT WITH SKIN OR EYES. IN CASE OF CONTACT, FLUSH The Guardian G600-B is intended for storage and IMMEDIATELY WITH WATER FOR 15 MINUTES. IF installation in indoor locations having ambient IRRITATION PERSISTS, CONTACT A PHYSICIAN. -
Page 6: Figure
FIGURE 3 BATTERY HOLDER FEATURES AND OPERATION OF THE G600-B CPU (P/N G602) There are several modes of operation. Reset/Power- reset, the result is a display of the green indictor for 2 On Mode, Diagnostic Test Mode, Fire Detect Mode, seconds, whereupon it enters Fire Detect Mode and Shut-Off Sequence, and Alarm Sequence. - Page 7 P/N G610B Page 6 April, 2016 (Rev 0) particular test, a sequence of audible chirps will sound operation, as it cannot pass the reset or diagnostic which represent a failure code (as well as a quick tests. flash of the red indicator). If multiple tests fail then you Shutoff Sequence will hear multiple series of beeps with a pause between each to identify multiple failure codes.
-
Page 8: Detection Sensor Assembly
P/N G610B Page 7 April, 2016 (Rev 0) DETECTION SENSOR ASSEMBLY (P/N G605) The sensor assembly, which is temperature activated, consists of two sensors mounted in a high temperature silicone rubber sleeve. The rubber sleeve contains magnets running along its length that allow for easy installation on the front edge of the underside of the hood or microwave-hood. -
Page 9: System Installation Instructions
Before beginning the installation of your Guardian Determine the best route from below the hood to G600-B unit, locate and identify each part. (See the location of the Extinguisher Assembly. Before FIGURE 1) Turn off the circuit breaker to the kitchen Drilling, measure the route and make certain that range hood and stove before boring holes. -
Page 10: Figure
(See Figure 6) 12. Reinstall the main CPU enclosure back onto the Guardian G600-B System Enclosure / Extinguisher Assembly and tighten the three screws loosened in step 6. Route and connect the sensor wires, solenoid wire and pressure gauge wire to the main CPU. -
Page 11: Aiming Nozzles
P/N G610B Page 10 April, 2016 (Rev 0) SYSTEM INSTALLATION INSTRUCTIONS (Cont'd) 16. Using the Nozzle Aiming Gauge provided, adjust AIMING THE SPRAY NOZZLES the nozzles to the correct angle based on the height determined in step 14. This is done by 14. -
Page 12: Electric Shutoffs
Both methods cause all electrical power to the stove to shut off. The dry contacts provided on the Guardian G600-B CPU are never to be wired directly to the cooking appliance to facilitate appliance shut-down. Either an electric shutoff (P/N G319) or gas shutoff (P/N G316-A) shall be used. - Page 13 P/N G610B Page 12 April, 2016 (Rev 0) INTERCONNECT CABLE IS STANDARD CONFIGURATION WIRELESS RECEIVER (OPTIONAL-SEE FIGURE 24) TO MAIN CPU (SEE FIGURE 3) OPTIONAL INTERFACE ENCLOSURE ASSEMBLY (See FIGURE 27) OPTIONAL ELECTRIC SHUTOFF RESET SWITCH POWER CORD- 3 PRONG AND OPTIONAL 4 PRONG OR A HARDWIRED ALARM / STROBE...
-
Page 14: Gas Shutoffs
Page 13 April, 2016 (Rev 0) GAS SHUTOFF (P/N G316-A) The Gas Shutoff Assembly G316-A is the shutoff supplied with the Guardian G600-B system when protecting a gas stove. Features provided with this TWO WAY shutoff include the following: N/C VALVE 1. - Page 15 P/N G610B Page 14 April, 2016 (Rev 0) VALVE POWER GAS FLOW RESET INTERCONNECT CABLE IS RESET INDICATOR STANDARD CONFIGURATION TO MAIN CPU OPTIONAL (SEE FIGURE 3) ALARM / STROBE (SEE FIGURE 26) POWER CORD FROM RANGE PLUG POWER CORD INTO WALL OUTLET WIRELESS RECEIVER (OPTIONAL-SEE FIGURE 24)
-
Page 16: Arming The System
6. Make sure all burners are off, then Reset the fuel shut-off (See “Reset Stove” page 12 for electric stoves or “Resetting Gas Shutoff Assembly” page 14) This completes the steps for "Arming the System”. The installation of the Guardian G600-B system is now complete. -
Page 17: Alternate Cam Activation
“Motor Test/Advance” Button and includes a “TRIP MOTOR” connection on the board instead of a The System is the same as the G600-B Solenoid Model “VALVE” connection. (See Figure 26) with the following exceptions: Note: Test the Trip Motor and Cam Monthly by removing The G600B-C uses a trip motor with cam for activation •... -
Page 18: Accessories
P/N G610B Page 17 April, 2016 (Rev 0) ACCESSORIES Building Alarm Interface (P/N G502INT) Manual Remote Pull Station (G309-A) DESCRIPTION: DESCRIPTION: The optional Building Alarm Interface (P/N G502INT) A manual remote pull station is available where local is provided to allow easy interfacing to external device fire codes or circumstances require the capability to i.e. - Page 19 P/N G610B Page 18 April, 2016 (Rev 0) ACCESSORIES (CONTINUED) Alarm / Strobe Assembly (P/N G320-A) DESCRIPTION: Both electric shutoff and gas shutoff provide an interface for a (120 volt-5A) alarm / strobe. This assembly has a Plug & Play configuration for ease of installation.
-
Page 20: Inspection And Maintenance
If the needle points to the "recharge" or G600-B system free of cooking grease residue. "overcharged" zone, contact an authorized Guardian Safety Every Twelve (12) years, a Guardian Safety Solutions, Intl. Solutions representative immediately for service. For G600- Distributor, holding all appropriate licenses/approvals for the... -
Page 21: After A Discharge
AFTER A DISCHARGE Disconnect the quick connect below the handle and IN THE EVENT A FIRE SHOULD OCCUR AFTER remove the distribution assembly from underneath the THE GUARDIAN G600-B SYSTEM HAS BEEN microwave hood / range hood. INSTALLED EXTINGUISHED FIRE,... -
Page 22: Parts List
* Indicates the part is optional or a TO MEET UL REQUIREMENTS, sub-assembly replacement part. USE ONLY DURACELL ** Indicates the part is an Alternate MN1604 OR ENERGIZER EN22 part for the Model G600B-C. BATTERIES IN THE GUARDIAN G600-B OR G600B-C SYSTEMS. Permit Number: 20-04649... -
Page 23: Troubleshooting Guide
P/N G610B Page 22 April, 2016 (Rev 0) TROUBLESHOOTING GUIDE CAUTION: DURING TROUBLESHOOTING PROCEDURES MAKE SURE A SPARE SAFETY PULL PIN IS INSTALLED IN THE EXTINGUISHER HANDLE. THE SPARE SAFETY PULL PIN MUST BE REMOVED FROM THE HANDLE WHEN TROUBLESHOOTING IS COMPLETE. Verify power is getting to stove by testing a Main CPU Board •... - Page 24 P/N G610B Page 23 April, 2016 (Rev 0) TROUBLESHOOTING GUIDE Gas Shutoff (P/N G316-A) (continued) Problem: No Electrical Power To Stove CAUTION: DURING TROUBLESHOOTING Confirm that power is supplied at the wall outlet. • PROCEDURES MAKE SURE A SPARE If no power at the wall outlet exist, check the site SAFETY PULL PIN IS INSTALLED IN THE condition.
- Page 25 P/N G610B Page 24 April, 2016 (Rev 0) TROUBLESHOOTING GUIDE Momentarily press the “Valve Reset” switch to • open the gas valve to the stove. The gas flow (continued) indicator light will illuminate CAUTION: DURING TROUBLESHOOTING Verify that the Interconnect cable between the •...
- Page 26 P/N G610B Page 25 April, 2016 (Rev 0) CPU board. TROUBLESHOOTING GUIDE (continued) If the stove successfully shut-off using the • interconnect cable then try installing the Wireless CAUTION: Transmitter/Receiver again, reset the gas shut-off DURING TROUBLESHOOTING and perform “Arming the System” procedures on PROCEDURES MAKE SURE A SPARE Page 15.
- Page 27 N/A - This is a mixture/preparation. Use of the preparation The intended or recommended use of this preparation is as a FIRE EXTINGUISHING AGENT. Company Identification Guardian Safety Solutions International Manufacturer/Supplier: 8701 John Carpenter Freeway, Suite 230 Dallas, Texas 75247 Address:...
- Page 28 Keep tightly closed until used. There is minimal danger to the environment from a storage release. The intended or recommended use of this preparation is as a FIRE EXTINGUISHING AGENT. Guardian Safety Solutions International Page 2 Rev Date: 05/15...
- Page 29 Energized electrical equipment may cause a shock hazard when this fire extinguishing agent is used. Hazardous decomposition product Normally stable Hazardous polymerization will not occur. Combustion or decomposition products include CO Guardian Safety Solutions International Page 3 Rev Date: 05/15 Permit Number: 20-04649...
- Page 30 All components are included in the DSL or are exempt from listing. Environmental restrictions: None are known Restrictions on Marketing and Use: None are known Refer to any other national measures that may be relevant Guardian Safety Solutions International Page 4 Rev Date: 05/15 Permit Number: 20-04649...
- Page 31 THE ABOVE INFORMATION IS BELIEVED TO BE CORRECT, BUT DOES NOT PURPORT TO BE ALL INCLUSIVE AND SHALL BE USED ONLY AS A GUIDE. GUARDIAN SAFETY SOLUTIONS INTERNATIONAL SHALL NOT BE HELD LIABLE FOR ANY DAMAGE RESULTING FROM HANDLING OR FROM CONTACT WITH THE ABOVE PRODUCT.
- Page 32 8701 John Carpenter Freeway Suite 230, Dallas TX 75247 Toll Free: (800) 786-2178 Fax: (972) 594-7826 www.guardianssi.com Permit Number: 20-04649...