Summary of Contents for The Things Network TTN Gateway v1 - EU
- Page 1 The Things Network Gateway assembly – Kickstarter batch version 1.0 date: 05-01-2017 -Assembly of the gateway PCB -Assembly of the gateway -Assembly of the gateway packaging...
- Page 2 Assembly of the Gateway PCB Product articles; • LoRa-module (A) • Gateway-PCB (B) Off the shelf parts: • 2 PCB support Notes: max dimensions of pcb holder end of document. Ignore the black/red wire on pcb. Gateway pcb is an old version...
- Page 3 Step 1. - Mount 2 pcb holder in gateway-LoRa Product articles; • LoRa-module • 2 pcb holders Notes:...
- Page 4 Step 2. - Place LoRa-module in gateway-pcb Product articles; • Gateway-pcb • LoRa-module Notes:...
- Page 5 Dimensions of pcb holder...
- Page 6 Assembly of the Gateway Product articles; • Gateway-Middle (A) • Gateway-bottom (B) • Gateway-top (C) • Gateway-PCB (D) • Gateway-Lightpipe (E) Off the shelf parts: • 2 suction cup • 4 adhesive rubber feet • SMA pigtail • 2 torq 3x8mm Notes:...
- Page 7 Step 1. - Place (2) suction cups in gateway-bottom Product articles; • Gateway-bottom • 2 suction cup Notes:...
- Page 8 Step 2. - Place gateway-pcb in gateway-bottom - Mount SMA pigtail in gateway-bottom, attach SMA pigtail to Gateway PCB Product articles; • Gateway-bottom • Gateway-pcb • SMA pigtail Notes:...
- Page 9 Step 3. - Place Gateway-lightpipe in Gateway-middle Product articles; • Gateway-middle • Gateway-lightpipe Notes:...
- Page 10 Step 4. - Place Gateway-middle on Gateway-bottom Product articles; • Gateway-assembly • Gateway-middle Notes:...
- Page 11 Step 5. - Mount (2) screws in Gateway-bottom Product articles; • Gateway-assembly • 2 torq 3x8mm screws Notes:...
- Page 12 Step 6. - Attach (4) adhesive rubber feet in Gateway-bottom Product articles; • Gateway-assembly • 4 adhesive rubber feet Notes:...
- Page 13 Step 7. - Attach sticker to the back of Gateway-bottom Product articles; Gateway-assembly Gateway sticker Notes:...
- Page 14 Step 8. - Snap Gateway-top on Gateway-middle Product articles; • Gateway-assembly • 4 adhesive rubber feet Notes: make sure that the lightpipe sloths on the gateway top align with the light pipe in the gateway-assembly...
- Page 15 Assembly of the Gateway packaging Product articles; • Gateway-assembly (A) • Gateway-Foam (B) • Carton sleeve (C) Off the shelf parts: • 12V 1.5A Adapter • SMA antenna Notes...
- Page 16 Step 1. - Place Adapater and antenna in Gateway-Foam Product articles; • Gateway-foam • 12V 1.5 Adapter • SMA Antenna Notes: Max dimensions of antenna & adapter next page >>...
- Page 17 Special note dimensions antenna & adapter Max dimensions adapter Max dimensions antenna A=70 mm B=30mm C=45mm Length: 22mm Diameter: 15mm...
- Page 18 Step 2. - Place Gateway-assembly in Gateway-Foam Product articles; • Gateway-foam • Gateway-assembly Notes:...
- Page 19 Step 3. - Place carton sleeve around gateway-foam, secure it with tape - Mark the 868 or 916 MHz corresponding with the Gateway Frequency Product articles; • Gateway-foam • Carton sleeve Notes:...
- Page 20 Step 3. - Place carton sleeve around gateway-foam, secure it with tape - Mark the 868 or 916 MHz corresponding with the Gateway Frequency Product articles; • Gateway-foam • Carton sleeve Notes:...
Need help?
Do you have a question about the TTN Gateway v1 - EU and is the answer not in the manual?
Questions and answers