Salto MARKS 5 LA1M 70 Series Installation

12,7 (1/2")
107 (4-3/16")
Auxiliary latch
(Anticard)
Anti-friction
5,6 (7/32")
Latch 19 (3/4") 70 (2-3/4")
107 (4-3/16")
25,4 (1")
Bolt
Anti-friction
Latch
5,6 (7/32")
Auxiliary latch
(anticard)
70 (2-3/4")
Latch 19 (3/4")
12,7 (1/2")
TO REVERSE HANDING:
1. Remove Front Plate.
2. Depress latch, unscrew bolt latch screws, one from
each side of the lock.
3. Tilt latch cam to remove latch bolt. Re-insert for
desired handing.
4. Replace latch screws and adjust bevel of backplate.
5. Replace front plate.
RH
R
L
www.saltosystems.com
All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any
item in this catalog, its design, construction, and/or materials.
3/8" (9,5 mm)
2-7/16" (
LA1M0570xxx..
32 (1-1/4")
27 (1-1/16")
LA1M1570xxx..
32 (1-1/4")
27 (1-1/16")
LH
62 mm)
Mortise Lock: SALTO LA1Mxx70XX...
Eng
ANSI A156.13 Grade 1 / Exceeds BHMA
LOCK INSTALLATIO N
PREPARING THE DOOR
Note: if the strike already exists in the door frame, position lock using strike as reference.
(See strike position on template)
1. Draw horizontal line on both sides and edge of door at the desired height of
knob above floor.
2. Draw vertical center line on door edge.
3. Draw vertical line on each side at the proper backset to align the template.
4. Position templates on edge and sides of door.
Mark holes ONLY for each side, and top and bottom holes of mortise cavity
on door edge, and holes in the lateral face of the door for handles, turnpiece
hole (only needed in inside face).
5. If lock has anti-friction latch, mark proper recess area on door edge template.
(See lock body to determine proper side.)
6. Remove template: place lock face against door edge.
Trace outline of faceplate as guide for faceplate routing.
MORTISE THE DOOR
1. Mortise door for lock body and faceplate per instructions on template.
INSTALLING THE LOCK BODY
1. Insert the lock into the cavity.
2. Mark & drill faceplate holes. Fasten with faceplate screws to hold lock in
place.
INSTALLING THE STRIKE
1. Refer to template to determine strike location on jamb.
2. Using strike as template, mark and chisel recess.
Drill screw holes and fasten.
ADJUST BEVEL
1. Loosen adjustment screws at top and bottom of case.
2. Turn fornt to desired bevel.
3. Re-tighten adjustment screws.
NOTE :
Holes for the fixation of the SALTO electronic escutcheon are not included in this template.
Please use the template included in the escutcheon box.
HANDING ANSI door code
Door code Mortise code
LH
L
RHR
RH
R
LHR
LUBRICATION
_____________________________________________________________________________________________________
All locks come lubricated from the factory with a lithium based grease. We recommend, however, continued periodic lubrication
of internal moving parts with a commercial quality grease. This can add years to the life of the lockset by reducing excessive
wear. For more severe environments, lubrication should be applied more frequently
Strike Lip Position
(Posición labio del cerradero)
(Position du recouvrement gâche)
MARKS 5 series
specifications / UL listed
® ®
Electro nic escutcheon Mortise locksets
C
L
OF
LEVER
C
L
OF
DOOR
EDGE
Adjustment
screw
Required Inf ormation
.
P-201454 -
OF
C
L LEVER
C
L
OF
BASKSET
Top of
Lock
Pivot
lock front
-ED.07/02/2011