Table of Contents
Advertisement
Quick Links
GLOBAL GEARED MOTOR
OPERATION MANUAL
GUA
SPEED CONTROL UNIT
■ Headquarters / 1st Factory : 22, Gyeongin-ro 3beon-gil, Bucheon-si, Gyeonggi-do, Republic of Korea
Tel:+82-32-664-7790 Fax:+82-32-611-7791
■ Attached research institute / No. 2 factory : 180, Oksan-ro, Bucheon-si, Gyeonggi-do, Republic of Korea
Tel:+82-32-684-7791
SERIES
Fax:+82-32-683-5059
www.ggm.co.kr
Advertisement
Table of Contents
Summary of Contents for CGM GUA Series
- Page 1 www.ggm.co.kr GLOBAL GEARED MOTOR OPERATION MANUAL SERIES SPEED CONTROL UNIT ■ Headquarters / 1st Factory : 22, Gyeongin-ro 3beon-gil, Bucheon-si, Gyeonggi-do, Republic of Korea Tel:+82-32-664-7790 Fax:+82-32-611-7791 ■ Attached research institute / No. 2 factory : 180, Oksan-ro, Bucheon-si, Gyeonggi-do, Republic of Korea Tel:+82-32-684-7791 Fax:+82-32-683-5059...
- Page 2 Thank you for purchasing the GGM product. Before use this product, read well manual certainly and understand all about knowledge, safety information and cautions of product, and use right way. After read, please be sure to keep fixed place to refer anytime. 1.
- Page 3 3. CONTROLLER CODING SYSTEM C : Single Phase 06 : 6W AC220V 50/60Hz 15 : 15W AC230V 50/60Hz 25 : 25W Unit Analogue AC240V 50Hz 40 : 40W Co.,LTD. Type Type 60 : 60W U : Single Phase 90 : 90W 120 : 120W AC110V 60Hz AC115V 60Hz...
-
Page 4: Installation Precautions
Rear side of main body 5. Precaution Use and operate device according to the following precautions. If do not follow the precautions, there may be electric shock, injury, worries of fire. Please keep certainly because it is important contents. Installation Precautions 1. -
Page 5: Handling Precautions
Wiring Precautions 1. If do parallel operation with controlled devices in electric furnace of high capacity, THYRISTOR for welding machine, there may be occasion of malfunction. Separate and wire by separate power circuit. 2. When do wiring CW-COM, CCW-COM for switching the direction at wiring for external remote control, please be careful not to be connected CW-COM, CCW-COM terminals at the same time. -
Page 6: Speed Control
6. Product Features 1. It is an UNIT product of detachable CONTROL MOTOR and CONTROL MOTOR. CONNECTOR is connected with the ONE TOUCH. It is most suitable in usage that remote control need.(There is not Moment stop function.) 2. There are assembled all needed devices of Speed control circuit, MOTOR CONDENSER, speed setter etc. - Page 7 8. How to use Setting for acceleration / deceleration time When operating CW Direction SPEED OUT SPEED OUT Frame Ground...
- Page 8 When operating CCW Direction SPEED OUT SPEED OUT Frame Ground When operating both CW and CCW Direction SPEED OUT SPEED OUT Frame Ground...
-
Page 9: Operation
SWITCH Specification SWITCH Number SWITCH Contact Capacity AC125V or AC250V over 5A AC125V or AC250V over 5A 8-1 Operation Connects LEAD line CONNECTOR of CONTROLLER UNIT and MOTOR, and connect AC terminal to AC power. If set RUN/STOP SWITCH of CONTROL UNIT by RUN side, MOTOR rotates clockwise direction when view at output side. -
Page 10: Mounting Method
9. Mounting method Processing of panels 1. Drill holes on mounting PANEL as shown figure below. Assemble CONTROLLER main body and front COVER and fix using M4 screws and nuts. 2. Use mounting PANEL with thickness of less than 2mm. PANEL TAP &... - Page 11 10. Failure Causes and Countermeasures Determination of Anomalies Measures for Check parts Checklist Breakdown Part whether the Wiring Wiring Check wiring wrong wiring correction If the voltage does not change, SPEED CONTROLLER is bad. Occasion If Power supply voltage is of MOTOR changing 0V ~ up to Check change...
- Page 12 ※ Contact your vendor or our second factory if you haveany questions about product or requirepost-sales service. Leader of geared motor GGM CO.,LTD. http://www.ggm.co.kr Headquarters / 1st Factory Attached research institute / No. 2 factory 22, Gyeongin-ro 3beon-gil, Bucheon-si, 180, Oksan-ro, Bucheon-si, Gyeonggi-do, Gyeonggi-do, Republic of Korea Republic of Korea TEL : 032-664-7790...