Summary of Contents for Nexo Dory
- Page 1 DP44098-03a-MG NEXO Dory Remote Control Over USB Software User Guide v2.03 for macOS, Windows and Android...
- Page 2 PAGE 2 OF 15 PRESENTATION Thanks for downloading NEXO Dory. This manual presents the app’s functionalities and how to use it step by step. PRESENTATION Dory is a remote control software intended to be used with NEXO Devices that have a USB control port.
- Page 3 ................... . Connecting the DTD to Dory .
- Page 4 DORY AND DTD FUNCTIONALITIES Although the DTD can be used without any external remote control software, it is needed to connect at least once the DTD to a computer running Dory to select the proper speaker setup. The DTD has a front panel mini-USB port for computer connection.
- Page 5 GeoM10 (x2~x3 cluster) with 63, 75, 85, 95, 120 Hz crossover – GeoM10 (Stack Monitor) with 63, 75, 85 Hz crossover The following sub or bass cabinet setups are available into Dory v2.03. Generic Sub – Generic sub preset with 40-85 Hz crossover, no protection IDS Series –...
- Page 6 PAGE 6 OF 15 DORY AND DTD FUNCTIONALITIES – GeoM6B (x1 Stand-alone) with 70 – 180 / 85-180 Hz crossover MSUB15 Series – MSUB15 Omnidirectional setup with 40 – 63/ 40 – 75/ 40 – 85/ 40 – 95/ 40 – 120 Hz crossover.
- Page 7 Dory has been developed as multiplatform software, being able to run on computers under Windows and macOS, as well as mobile or tablet devices under Android. Starting from version 1.12, Dory will notify if a new version is available (requires an internet connection).
- Page 8 3. Wait while necessary drivers are installed. The DTD uses only pre-installed Windows drivers and does not need any speci c download. 4. Once Windows claims that the hardware has been successfully installed, you can launch Dory through the shortcut in the start menu of through the search bar.
- Page 9 USING DORY Upgrading the DTD firmware When Dory detects a DTD on a USB port of the computer, it will rst check the rmware revision of the device. If the rmware inside the DTD is different from the one embedded...
- Page 10 PAGE 10 OF 15 USING DORY Changing the Speaker Setups Speaker setups can be changed separately for main and sub, meaning that any combination of Main Speaker (stereo) and Sub speaker (mono) is available. However, it is not possible to process to different speakers for main left and main right.
- Page 11 USING DORY PAGE 11 OF 15 press [OK] once you made your choice. Dory will then upload the speaker preset into the DTD’s internal memory. You can then select among the available crossovers (check that the front panel’s switch is on the USER position, otherwize this feature will be read-only).
- Page 12 PAGE 12 OF 15 USING DORY Inputs and patching page The rst button will lead you to the input settings. From this page you can adjust: – Input meters for all inputs (Digital L/R stands for USB audio input as the DTD is also detected by Windows as a USB soundcard, or Dante inputs, see below).
- Page 13 L+R is selected, -6 dB of gain is applied automatically internally. – User compressor. This compressor can be setup by the user to limit the output level on top of NEXO’s internal protections (to limit the speaker output level to a certain SPL for example).
- Page 14 Using lock device, it is possible to lock the unit with a pin code. This code will be asked before editing any setting on the unit. – Tutorial shows a detailed tour of the software’s features. – Automatically look for software updates enables to be noti ed as a new Dory’s version is released.
- Page 15 Feedback and Bug Reporting: technical@nexo.fr. Thanks for your cooperation! NEXO SA cannot be held responsible for damages caused by improper use of the devices, this software and its manual. This software and manual are the exclusive copyrights of NEXO SA. Copying and reproduction of the software or of its manual, even partly, are forbidden without the written consent of NEXO SA.
Need help?
Do you have a question about the Dory and is the answer not in the manual?
Questions and answers