Do you have a question about the BTS-1000 and is the answer not in the manual?
Questions and answers
Summary of Contents for Biontech BTS-1000
Page 1
USER GUIDE BOOK Electrolysed Water Sanitiser BTS-1000 Please read this manual before using this device to ensure safe and correct use...
Page 2
Be aware of the following before using the electrolysed water sanitiser. WARNING! Follow all the instructions in this manual carefully. Keep out of reach of children, infants and animals. DON'T use in confined spaces. Always use in well ventilated areas. DON'T spray directly toward people or animals and don't inhale the electrolysed water vapour.
Page 3
01 Introduction Safe sanitised, deodorising and oxidising water generated by the latest electrolysis technology. Using common tap water, it can produce strong electrolysed water (Hypochlorous acid - HOCL) for sanitising, deodorising and cleaning. Powerful electrolysis method via titanium electrodes. Smart current control - guarantees current safety overload. Safe to use on skin (with no accelerator).
Accelerant Accelerant 촉진제 Spoon Base Product specification Product name Electrolysed water sanitiser (Spray BTS-1000, Pitcher BTS-1100) 1 product set, Spray, AC plug, AC Adaptor, Accelerant, Spoon, BTS-1000 Components User's guide. Spray - D 90 x W 90 x H 265...
Component Installation Attach the adaptor's connector into the bottom of the base groove as shown in figure 1. Then sit base on a flat dry surface and plug in power supply. Figure 1 Explanation of terms Electrolysis Electrolysis is a process of decomposing water through an electrochemical redox reaction by applying electricity to the process.
06 Using the device 1. Fill up the bottle to the maximum level with tap water. 촉진제 0.5g Accelerant 0.5g The maximum is 350ml 2. For a stronger solution, add a level teaspoon (0.5g) of accelerant to the water. 3. Combine with water, stir well before starting the electrolysing process.
Page 7
4. The sprayer bottle fits onto the top of the base. 5. Pressing the Power Button (middle button) will activate the base unit. Two settings, either press the low or high button. Low : 1 min run time / generating standard electrolysed water. High : 2 min run time / generating strong electrolyzed water.
07 Maintenance Maintenance The electrolysed water in the device will neutralise after about 3-5 days. When the device is not in use for a long period of time (weeks), tip out the water and allow the device to dry. Place in a dry space out of direct sunlight. Don't store in a fridge as it may degrade the device’s performance and cause it to stop working.
08 Safety precautions Cautions when using the device DON'T use in confined spaces. Always use in well ventilated areas. DON'T inhale or drink the electrolysed water. If you drink the electrolysed water consult a doctor immediately. DON'T spray into anyone's eyes. If it gets into your eyes, immediately rinse with clean water and consult a doctor.
Trouble shooting guide Condition Check Action LED light off Is the power connected Try again after connecting the power properly? properly. Press the power on button. LED light on. However Is the sprayer bottle Refer to page 5. Properly combine the air bubbles have not properly connected with sprayer bottle with the base and then try...
Failure caused by plugging the device into an incorrect voltage power supply. Failure as a result of using parts or consumables that are not produced by Biontech. Loss of or damage to parts as the result of customers disassembling the device.
Page 12
For all customer and service inquiries, call us on 1800 268 469 or email : info@alkaway.com.au AlkaWay Australia | www.alkaway.com.au AlkaWay United States | www.alkaway.com AlkaWay Canada | www.alkaway.ca AlkaWay UK | www.alkaway.co.uk AlkaWay EU | www.alkaway.eu AlkaWay Singapore | www.alkaway.sg AlkaWay Support | support.alkaway.com Copyright AlkaWay 2021...
Need help?
Do you have a question about the BTS-1000 and is the answer not in the manual?
Questions and answers