Advertisement
Prior to proceeding with the following manual please notice this update:
Please see that part ( A ) will be included with and attach
to your device. Used instead of ( C ) below.
A.
A.
This part will act as your rear rotation stop.
Screw will press
in these two areas.
some angled screens and screens bezels.
PRODUCT GUIDE
Position in the
hole
Behind
the white
motion
sensor
lens. So the
tape contacts the
shell.
Illustration of previous instructions
Long
Long
Bottom view
C.
C.
This part will minimize
This part will minimize
0 degrees
0 degrees
free rota on.
free rota on.
Long screw
Long screw
holds rotation position with a
holds rotation position with a
Short
Short
small amount of pressure.
small amount of pressure.
Tighten until firm only.
Tighten until firm only.
proximitysystems.com/uvclean
Made in th
15 degrees
15 degrees
(FLAT SQUARE)
(FLAT SQUARE)
i.
7/20 Rev 0
7/20 Rev 0
Advertisement
Table of Contents
Summary of Contents for ProxiMity UV-CLEAN
- Page 1 Made in th PRODUCT GUIDE Prior to proceeding with the following manual please notice this update: Please see that part ( A ) will be included with and attach Bottom view to your device. Used instead of ( C ) below. Position in the hole Behind...
- Page 2 Made in the Proximity UVC-SM PRODUCT GUIDE proximitysystems.com/uvclean REV F /2020...
-
Page 3: Table Of Contents
Proximity UVC-SM CONTENTS 1. Quick Guide 2. Safety & Disposal 3. Set-Up 4. How It Works 5. How It Works, Se�ng Changes 6. How It Works, Audit Records 7. Warranty Terms REV F /2020... -
Page 4: Quick Guide
A�ach bracketry according to instruc�ons found in this guide. See contents below. A�ach the power cable to the circular jack on the back of the UV-Clean unit. Power the device by plugging in the opposite end of the power cable to the USB 3.0... -
Page 5: Safety & Disposal
Federal Universal Waste Rule Maintenance Do not a�empt to service this product. Contact customer service at Proximity Systems for guidance. Do not subject the bulb to fingerprints, solvents or abrasion. Cleaning the bulb with a damp cloth or lens �ssue is advised when the unit is not plugged in and the device is at room temperature only. -
Page 6: Set-Up
Proximity UVC-SM SET-UP ( OPTION A. ) ( OPTION B. ) A) Step 1: B) Step 1: Place the stand between A�ach the monitor bracket. Between the the UVC device and the main bracket. UVC device and the main bracket. -
Page 7: How It Works
Proximity UVC-SM HOW IT WORKS Cleaning Opera�on Timing When posi�oned and plugged into power, your UV-Clean device will begin working. Clean Time: The period of �me the device is It has pre-set opera�on �mes. producing UV-C. Factory set to 3 minutes. -
Page 8: How It Works, Se�Ng Changes
Proximity UVC-SM HOW IT WORKS Data Retrieval and Making Changes If informa�on from or changes to the device are needed. Required: Plug in micro USB data cable. For data transfer to PC. Downloaded so�ware from the product website is also required. - Page 9 Audit Records: Each logged event for the UV-Clean performing a cleaning func�on. Erase All Records This will permanently eliminate the logged events stored within the UV-Clean device memory. Save to File: This will export the cleaning data to a .csv file for use on a PC. The following informa�on is included: •...
-
Page 10: Warranty Terms
If any Proximity manufactured product is or becomes defec�ve during the warranty period, Proximity will, at its op�on, either repair, exchange or replace defec�ve unit. The purchaser should contact our Service Department for service. Proximity reserves the right to make design changes in manufactured products built and/or sold by them at any �me without incurring any...
Need help?
Do you have a question about the UV-CLEAN and is the answer not in the manual?
Questions and answers