Advertisement
Quick Links
1-Channel Universal Dimmer for DIN rail mounting (350W@230VAC/200W@110VAC)
ZDIDBDX1
FEATURES
•
1 channel for R L C loads and for dimmable CFL and LED lamps.
•
Automatic detection of R L C load type.
•
Automatic frequency detection.
•
Dimming pattern selection for CFL and LED lamps.
•
Optional manual dimming control.
•
Total data saving on KNX bus failure.
•
Integrated KNX BCU.
•
Dimensions 67 x 90 x 36mm (2 DIN units).
•
DIN rail mounting (EN 50022), through pressure.
•
Conformity with the CE directives (CE-mark on the right side).
1. Output channel
5. Programming/Test push button
Programming/Test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe
mode. If this button is held for more than 3 seconds, the device enters the test mode.
Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode
is indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode, it emits a red flash.
GENERAL SPECIFICATIONS
CONCEPT
Type of device
Voltage (typical)
Voltage range
KNX supply
Maximum
consumption
Connection type
External power supply
Operation temperature
Storage temperature
Operation humidity
Storage humidity
Complementary characteristics
Protection class
Operation type
Device action type
Electrical stress period
Degree of protection
Installation
Minimum clearances
Response on KNX bus failure
Response on KNX bus restart
Operation indicator
Weight
PCB CTI index
Housing material
¹ Maximum consumption in the worst-case scenario (KNX Fan-In model)
© Zennio Avance y Tecnología S.L.
2. Power supply input
6. Programming/Test LED
Voltage
29VDC (typical)
24VDC¹
Edition 4
3. Output status LEDs
DESCRIPTION
Electric operation control device
29VDC SELV
21..31VDC
mA
7.05
10
Typical TP1 bus connector for 0.80mm Ø rigid cable
110/230VAC 50/60Hz
0°C .. +55°C
-20°C .. +55°C
5 .. 95%
5 .. 95%
Class B
II
Continuous operation
Type 1
Long
IP20, clean environment
Independent device to be mounted inside electrical panels with DIN rail (EN
50022)
Not required
Data saving according to parameterization
Data recovery according to parameterization
The programming LED indicates programming mode (red) and test mode
(green). The output LED indicates its status (fixed = active output; flashing
= error in the output)
105g
175V
PC FR V0 halogen free
Futher information
DIMinBOX DX1
TECHNICAL DOCUMENTATION
2
3
4
5
6
7
Figure 1: DIMinBOX DX1
4. Manual control push buttons
7. KNX connector
mW
204.45
240
www.zennio.com
1
Page 1/4
Advertisement
Related Manuals for Zennio DIMinBOX DX1
Summary of Contents for Zennio DIMinBOX DX1
- Page 1 = error in the output) Weight 105g PCB CTI index 175V Housing material PC FR V0 halogen free ¹ Maximum consumption in the worst-case scenario (KNX Fan-In model) © Zennio Avance y Tecnología S.L. Edition 4 Futher information www.zennio.com Page 1/4...
- Page 2 • The facility must be equipped with a device that ensures the omnipolar sectioning. Installation of a 10A mini-circuit-breaker is recommended. To prevent accidents, it must remain open in case of manipulation of the device. • The device has a short-circuit protection fuse that, in case of activation, should only be rearmed or replaced by the Zennio technical service.
- Page 3 Once the ambient temperature decreases, the dimmer actuator will resume its normal operation. Please, refer to user manual. Attaching DIMinBOX DX1 to DIN rail: Removing DIMinBOX DX1 from DIN rail: Figure 3: Mounting DIMinBOX DX1 on DIN rail © Zennio Avance y Tecnología S.L. Edition 4 Futher information www.zennio.com...
- Page 4 Alternating blink of each LED during one-second, Anomalous Frequency followed by a one-second switch off. Output status LEDS One LED blinks every second while the other LED Parameterization Error blinks every 0.25 second. © Zennio Avance y Tecnología S.L. Edition 4 Futher information www.zennio.com Page 4/4...