1. Manuals
  2. Brands
  3. GAELCO Manuals
  4. Game
  5. Ring Riders
  6. Operator's manual

GAELCO Ring Riders Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IT IS THE RESPONSIBILITY OF THE OPERATOR TO CARE ABOUT COSTUMER SAFETY AT ALL
TIMES. PLEASE READ AND OBSERVE THE NOTES ON SAFETY DESCRIBED IN THIS MANUAL.
OPERATOR'S MANUAL
1st EDITION
VERSION 1.1
© GAELCO 2004

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ring Riders and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GAELCO Ring Riders

  • Page 1 OPERATOR’S MANUAL 1st EDITION VERSION 1.1 © GAELCO 2004 IT IS THE RESPONSIBILITY OF THE OPERATOR TO CARE ABOUT COSTUMER SAFETY AT ALL TIMES. PLEASE READ AND OBSERVE THE NOTES ON SAFETY DESCRIBED IN THIS MANUAL.
  • Page 2 GAELCO - RING RIDERS About RING RIDERS Thank you for purchasing this Gaelco S.A. product. This manual explains how to safely operate your game machine. Failing to operate the machine correctly could result in malfunction or accident, so please read the manual carefully before starting operation, specially the SAFETY NOTES (Section 3).
  • Page 3 GAELCO -RING RIDERS INDEX GENERAL INFORMATION 9.4.1 Drive chain adjustment Manufacturer and Machine data 9.4,2 Brake cable Legislation references Brake sensor adjustment Technical Service Brake stopper Responsibility Throttle cable Moton system MACHINE SPECIFICATIONS Emergency stop 9.10 Error messages SAFETY NOTES 9.11 Pedal microswitch...
  • Page 4 GAELCO - RING RIDERS...

  • Page 5: General Information

    GAELCO - RING RIDERS GENERAL INFORMATION 1.1 MANUFACTURER AND MACHINE DATA Manufacturer GAELCO, S.A. Address Escipión 11 08023 City Barcelona Country: SPAIN Tel. 34 93 417 36 26 34 93 417 28 02 e-mail gaelco@gaelco.com Technical Service sat@gaelco.com Name of the game...

  • Page 6: Technical Service

    SPECIFICATIONS GAME DESCRIPTION RING RIDERS is a motorbike competition, placed in a Theme Park, where up to four players race head to head against the clock. The race challenges the player’s ability to control the bike under many different and changing conditions. The score is obtained by getting through rings that appear along the course, though the acrobatics achieved and the finish position are important too.

  • Page 7: Cpu Board

    GAELCO - RING RIDERS 3) Total dimensions of the machine, installed on site: width depth height 1100 mm 2650 mm 2162 mm POWER SUPPLY Operating Power: 220-230 VAC, 50 Hz Output: +3,3VDC / 15A +5VDC / 12A, +12VDC / 8A MONITOR 34"...

  • Page 8: Safety Notes

    When transporting or reselling the machine, be sure to attach this Manual. The RING RIDERS machine has been designed for indoor use only, within residential or commercial areas, and must be used exclusively for the purpose intended.

  • Page 9: General Safety Considerations

    GAELCO - RING RIDERS 3.1 GENERAL SAFETY CONSIDERATIONS • Before operating the machine, check that it has been installed correctly and in accordance with this Manual. • As some parts of the machine move during game play, there are places where the distance between the stationary section and the mobile section changes.
  • Page 10 • Do not run the power cord across passages where pedestrian's feet could get caught on the cord. • Ensure that the location’s power supply is equipped with an Earth Leakage Breaker rated at 30mA. GAELCO shall not be held responsible for any damage resulting from the failure to observe these instructions.

  • Page 11: Precautions To Be Heeded When Moving The Machine

    3.2.1 SECURING IN PLACE Ensure that all the leg levellers make firm contact with the surface of the floor. This precaution is crucial for the RING RIDERS version with motion system, because the machine can move of itself, causing an accident.
  • Page 12 GAELCO - RING RIDERS 3.4 PRECAUTIONS TO BE HEEDED DURING OPERATION Please heed the following indications in order to ensure the safety of the customers when using this game machine. Be sure to read and get a good understanding of each item: •...
  • Page 13 GAELCO - RING RIDERS 3.5 SAFETY DEVICES CONCERNING THE MOTION SYSTEM The RING RIDERS / MOTION machine has two dedicated devices that provide additional safety to the player when the game is running: • An EMERGENCY STOP BUTTON placed on top of the fuel tank, which can be easily activated by the player or the operator at any time.
  • Page 14 Store the packed machine in sheltered and dry areas. Temperatures allowed: maximum +45ºC / minimum -5ºC. 4.3 RECEPTION The RING RIDERS packaging should be carefully inspected upon receipt to ensure that the product is delivered in good conditions. Shipping damage may void warranty. In case of shipping damage, contact your Distributor...
  • Page 15 Once the packaging is removed, the machine looks as shown in the illustration. 5.1 INSPECTION BEFORE ASSEMBLING Normally, GAELCO products are ready to assemble immediately after transporting to the location. Nevertheless, some mishandling may occur during transportation. Check the following points to ensure that the machine has been properly delivered: •...
  • Page 16 GAELCO - RING RIDERS 5.2 ASSEMBLING & INSTALLATION To assemble the machine proceed as follows: 1. Take out the boxes containing the accessories. 2. Remove the metal brackets that fix each unit to its pallet. 3. Raise the leg levellers and put the units down on the floor with the help of a ramp. Be very careful to avoid the risk of being crushed! 4.
  • Page 17 GAELCO - RING RIDERS Screw the short end of the fixing bars onto the back of the billboard, as indicated in the picture below. Assemble the billboard on the top of the monitor cabinet, using a step. Do not climb on the cabinet! Plug the connector of the fluorescent tubes and fix the billboard with the butterfly nuts.
  • Page 18 GAELCO - RING RIDERS 7. The union harness comes with the platform. This part is disassembled for shipping facility, as shown in the picture below. Please fix the harness before to move the platform. The screws are already mounted on its place. Loose them and srew them again fixing the harness plate.
  • Page 19 GAELCO - RING RIDERS When all connectors are plugged, approach the platform to the cabinet so you can fix the harness plate of that end. The screws are already installed on its place. 9.The gap (D) between the platform and the monitor cabinet should be 210mm (9”) approximately.
  • Page 20 GAELCO - RING RIDERS 10. Level the platform.Carefully adjust all the levellers so that the whole machine rests firm and level on the floor. (See section 3.2). Remember that the platform contains a motion system! 11. Proceed to assemble the back rail to the platform. First of all connect the cable, then fix the rail.

  • Page 21: Switching On The Machine

    GAELCO - RING RIDERS 5.3 GETTING READY TO START BEFORE SWITCHING ON THE MACHINE, PLEASE CHECK THAT THE INTALLATION FITS ALL THE REQUIREMENTS DESCRIBED ON CHAPTER 3 (SAFETY NOTES) AND ESPECIALLY THOSE OF SECTION 3.2 The installation of the machine at its final site should be carried out by trained people.
  • Page 22 GAELCO - RING RIDERS PROGRAMMING THE MACHINE AND TEST MODE An automatic check of the memories is made when the machine is switched on. This coincides with the presentation of the Screen Test. After a few seconds, if no error occurs, it automatically goes on to show the game.

  • Page 23: Screen Test

    GAELCO - RING RIDERS 6.1 SCREEN TEST This screen is the ADJUSTMENT CARD, which should be used to suitably adjust the monitor. It shows you, also, information about the installed software version. You can return to de Main Menu by pushing the START button placed on the right side of...

  • Page 24: Input / Output Test

    GAELCO - RING RIDERS 6.2 INPUT / OUTPUT TEST This screen enables you to check the correct functioning of all controls of the machine. The device to be tested is selected by pushing the START and VIEW buttons placed on the fuel tank cover.
  • Page 25 GAELCO - RING RIDERS Start button Placed on top of the fuel tank (right side). The light ring that sorrounds the monitor is activated when pressing this button. View Button Placed on top of the fuel tank (left side). The light ring is also activated when pressing this button.

  • Page 26: Sound Test

    GAELCO - RING RIDERS The options Forward and Reverse allow you to check the position of the bike for maintenance purposes. The bike can move slowly or fast, depending on the throttle regulation. The Motion test option performs an automatic check of the steering motor and the motion motor.
  • Page 27 GAELCO - RING RIDERS 6.5 SETTINGS As for the previous screens, the parameter is selected with the VIEW and SIREN buttons, then changed by a twist of the accelerator grip (throttle). SETTINGS Difficulty: Easy Advertising sound: Free play: Credits to start:...

  • Page 28: Book-Keeping

    GAELCO - RING RIDERS Link mode Up to four RING RIDERS machines can be linked together. The link status is detected automatically. When just two machines are linked, you only need the link cable supplied with each machine. This crossed Ethernet cable should be plugged to the RJ45/8 connector of the RIN-364 unit (mains switch and fuse holder).placed on the rear bottom of...
  • Page 29 Next Page Reset book-keeping Exit WARNING: GAELCO is not leable for any accidental lost of data. To leave this screen and return to the Main Menu, select Exit and twist the accelerator grip. 6.7 LEAVING THE TEST MODE The last two options of the main menu allows you to leave the test mode and go back to the play mode.

  • Page 30: How To Play

    HOW TO PLAY Game's Concept RING RIDERS is a motorbike competition, placed in a Theme Park, where up to four players race head to head against the clock. The race challenges the player’s ability to control the bike under many different and changing conditions. The score is obtained by getting through rings that appear along the course, though the acrobatics achieved and the finish position are important too.

  • Page 31: Advanced Options

    2. Take as many cables as machines. If you can’t find a network switch with automatic polarity detection, the link cable supplied by Gaelco is not suitable, as it is a crossover Ethernet cable. In that case you have to use normal patch cable.
  • Page 32 7. Switch off the RING RIDERS machine to be updated. Remove the base cover of the monitor cabinet (RIN-220) so you can access to the CPU. 8. Plug the USB Memory Sticker to one of the USB ports of the RING RIDERS CPU. 9. Switch on the machine. The update begins automatically.

  • Page 33: Safety Precautions

    • Make sure there is plenty of room for maintenance to be carried out. At least 3 metres should be left free between the machine itself and other objects (e.g. adjacent machines, walls, etc.). • When parts needs replacing, use only those approved by Gaelco S.A. and which meet the relevant specifications.

  • Page 34: Brake Lights

    GAELCO - RING RIDERS 9.3 BRAKE LIGHTS If the brake lights can be checked by removing the screw that holds de exhaust pipe, as shown in the drawing. The light board (2) is released by pulling the snap rivet (1).

  • Page 35: Adjusting The Drive Chain Tension

    GAELCO - RING RIDERS 9.4.1 ADJUSTING THE DRIVE CHAIN TENSION Adjust the chain tension as follows: 1. Loosen the screws holding the tensing roller shafts (as shown in the drawing). Half a turn should be enough. 2. Then, adjust the chain tension by tightening the side screws. To check whether the chain is properly tensed: the nylon rollers should press tightly enough against the chain to be difficult to turn by hand but still sufficiently loose to be able to turn despite the friction.
  • Page 36 GAELCO - RING RIDERS Checking the rollers 3. Tighten the top screws and re-check the pressure of the rollers against the chain. If they cannot be turned by hand, they are pressing too hard against the chain. If this is the case, repeat the process again, this time loosening the side screws a little.

  • Page 37: Brake Cable Replacement

    GAELCO - RING RIDERS 9.4.2 BRAKE CABLE REPLACEMENT To replace the brake cable, proceed as follows: 1. To work more easily, remove the steering assemby following the procedure described in the section 9.3 of this chapter. 2. Remove de protective cover from the brake handle.
  • Page 38 GAELCO - RING RIDERS 4. Loosen the nuts that hold the cable tensor to the mechanism, using two spans of 12mm. Then release the cable. 5. Lift the cable from the plastic cupola by pulling it upwards. 6. Fit the new cable by following the reverse procedure. First thread the cable into the cupola from the top.
  • Page 39 GAELCO - RING RIDERS 9.5 ADJUSTMENT OF THE BRAKE SENSOR The brake sensor consists of a magnet (2) and a Hall IC (1). The magnet is mounted on the lever (3) that activates the micr-switch (4). The IC is mounted on a printed circuit board including a connector.

  • Page 40: Sensor Adjustment

    GAELCO - RING RIDERS 9.5.2 SENSOR ADJUSTMENT To adjust the sensor proceed as follows: • Switch off the machine. • Remove the steering mechanism, as explained in section 9.4 of this chapter. • Loosen -just a bit- the screws that fix the sensor board. The right hole of the board allows you to move it up and down a few millimeters, pivoting on the left screw.
  • Page 41 GAELCO - RING RIDERS • Keeping the handle pressed, move carefully the sensor board, until you find the position where the reading is any value between 170 and 180. • Tighten up the screws and check again the operation of the sensor, following the procedure explaned on the previous section (9.5.1).
  • Page 42 GAELCO - RING RIDERS 9.6 REPLACEMENT OF THE STOPPER t is not necessary to remove the brake handle for replacing the stopper. Loosen the screw shown in the drawing gives you enough room to take out the stopper. Some force must be applied to unscrew the stopper as it is fixed with medium strength nutlock.
  • Page 43 GAELCO - RING RIDERS 3. Remove the screw that locks the tensor, then remove the tensor. 4. Remove the screw that holds the cover of the throttle. Use the proper allen key (4mm) as some force ins necessary because the screw is fixed with medium strength threadlocker.
  • Page 44 GAELCO - RING RIDERS 7. Fit the new cable by following the reverse procedure. First thread the cable into the cupola from the top. Then follow the steps below: • Fit the end of the cable in the lever. • Fit the tensor.on the steering mechanism.

  • Page 45: Power Board

    GAELCO - RING RIDERS BLOCK DIAGRAM OF THE MOTION SYSTEM CPU BOARD RING RIDERS game board (RIN-357) POWER BOARD DC motor driver (RIN-358) COMMANDER SE AC motor driver (RIN-392)

  • Page 46: Security System

    GAELCO - RING RIDERS 9.9 SECURITY SYSTEM The Commander SE has a security loop that goes through an emergency stop switch and two micro-switches installed on the front footrests. If the emergency button is pressed, or any of the footrest switches are released, the “ready” input of the Commander drops to 0V and the motor does not receive any current.

  • Page 47: Safety Stop

    GAELCO - RING RIDERS If the red knob is pressed along the play, a warning message is displayed on the screen indicating how to unlock the knob. When this message is not displayed but the bike does not move, the safety stop circuit should be tested.
  • Page 48 GAELCO - RING RIDERS 9.10 ERROR MESSAGES FROM THE MOTOR DRIVER The RING RIDERS CPU and the motor driver Commander SE (RIN-392) communicate through a RS-485 serial interface. The Commander receives control signals from the CPU and sends status signals.
  • Page 49 GAELCO - RING RIDERS 9.11 REPLACEMENT OF THE FOOTREST MICRO-SWITCH A faulty micro-switch can cause the permanent stop of the motion system, as explained in Section 9.9.2 of this chapter. Removing the front cover allows the access to the footrest micro-switches.
  • Page 50 GAELCO - RING RIDERS 9.12 DISASSEMBLY OF THE PROTECTION HOOD Proceed as follows when accesing areas covered by the protection hood: 1. Enter the MOTION SYSTEM screen in Test Mode and rise the bike platform up to highgest position, using the throttle grip and the options Forward / Reverse. For more details, consult Section 6.3 of this manual.
  • Page 51 GAELCO - RING RIDERS 9.13 CHECKING THE POSITION POTENTIOMETERS If the bike does not move properly, and the troubleshooting leads to a possible fault in the position potentiometer (RIN-850), proceed as follows: 1. Disassembly the protection hood, as explained in the previous section (9.12). The drawing below shows the position potentiometers.
  • Page 52 GAELCO - RING RIDERS 3. If the reading is quite different from 128 when the shaft crank is in horizontal position, it is necessary to adjust the potentiometer B. 4. To check the potentiometer A enter the option Lateral leaning of the INPUT / OUTPUT menu.

  • Page 53: Troubleshooting Procedures

    GAELCO - RING RIDERS 9.14 TROUBLESHOOTING PROCEDURES 1) PROBLEM:The machine does not start when the mains switch is thrown. CHECKS • Check the mains cable and its connections. • Check the fuses. Check that the specifications are met. Check whether the fuses have blown and that they have the correct current rating (10A).

  • Page 54: Technical Assistance

    GAELCO - RING RIDERS 6) PROBLEM:The throttle does not work. CHECKS • Check the throttle operation on the INPUT / OUTPUT screen of Test mode. If the reading does not changes when you twist the grip, check the cable. • Twist the grip, then leave it: the grip should twist back to the rest position. If this is not the case, check the the cable, the spring that pulls it and the pulley wheel.
  • Page 55 GAELCO - RING RIDERS NOTES ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

  • Page 56: Parts List

    GAELCO - RING RIDERS 10. PARTS LIST 10.1 MONITOR CABINET – DESIGN RELATED PARTS CODE DESCRIPTION RIN-520 BILLBOARD ASSEMBLY RIN-511 TRANSLUCENT COVER - RIGHT RIN-512 LAMP ARRAY TUBE RIN-510 FRONT COVER - BLUE RIN-513 TRANSLUCENT COVER - LEFT...
  • Page 57 GAELCO - ATV QUADS TRACK 10.2 MONITOR CABINET– BILLBOARD ASSEMBLY CODE DESCRIPTION SCREW UM1001 M5X10 RIN-524 FLUORESCENT RING Ø220mm RIN-523 FLUORESCENT RING Ø400mm RIN-521 BASE RIN-525 BALLAST 20W / 220V for Ø220mm fluorescent ring RIN-526 BALLAST 40W / 220V for Ø400mm fluorescent ring...
  • Page 58 GAELCO - RING RIDERS 10.3 MONITOR & SUBWOOFER CODE DESCRIPTION RIN-350 MONITOR POLO/2 34” STAR PH - 02197790 - CABLE SVGA 600mm NUT DIN985 M8 FLAT WASHER DIN125 M8 NUT DIN934 M8 SCREW DIN603 M8X45 RIN-231 SPACER, M6 at both ends...
  • Page 59 GAELCO - RING RIDERS...
  • Page 60 GAELCO - RING RIDERS 10.4 MONITOR CABINET– COIN DOOR & LOUDSPEAKERS CODE DESCRIPTION RIN-223 COIN ACCEPTOR RAIL RIN-411 MINIDOOR, 1 ENTRY - CODE P10017075101000 SCREW 3,9X13 SCREW DIN7985 M4X10 RIN-230 SERVICE PANEL RIN-227 BRACKET, service panel SCREW 3.9X13 RIN-360 5” SHIELDED LODSPEAKER, 60W, 4Ω - CODE 35.1368...
  • Page 61 GAELCO - RING RIDERS 10.5 MONITOR CABINET - COIN BOX & MAINS SWITCH CODE DESCRIPTION RIN-412 MINI BLANK DOOR COB:6133 RIN-416 PLASTIC CASH BOX - STANDARD RIN-367 VENTILATION GRILL 15X15 SCREW 3,9X13 RIN-364 MAINS SWITCH & FUSE HOLDER + RJ45/8 CONNECTOR...
  • Page 62 GAELCO - RING RIDERS 10.6 MONITOR CABINET – BASE COVERS CODE DESCRIPTION RIN-220 METALLIC COVER - FRONT SCREW UM1001 M6X16 RIN-221 METALLIC COVER - REAR SCREW DIN7505D 5X30 SCREW 4,1X20 RIN-222 UNION BRACKET, metallic covers...
  • Page 63 GAELCO - RING RIDERS 10.7 MONITOR CABINET – REAR PARTS CODE DESCRIPTION RIN-367 VENTILATION GRILL 15X15 SCREW 3,9X13 RIN-353 LIGHT CONTROLLER PCB, lamp array tube SCREW 3,5X20 RIN-435 DOOR LOCK, AGA 135 RIN-105 BACK DOOR, monitor cabinet...
  • Page 64 GAELCO - RING RIDERS 10.8 MONITOR CABINET – ELECTRONIC PARTS CODE DESCRIPTION RIN-357 CPU - RING RIDERS RIN-355 PSU - PSATX10300 RIN-358 DC MOTOR DRIVER & DC LEVEL ADAPTOR RIN-224 SUPPORTING PLATE, transformer RIN-363 FAN 220V, 120X120X38mm RIN-370 TORIOIDAL TRANSFORMER 220/18-0-18, 160VA RIN-364 MAINS SWITCH, FUSE HOLDER (2X10A) &...
  • Page 65 GAELCO - RING RIDERS 10.9 MONITOR CABINET – BOTTOM PARTS CODE DESCRIPTION NUT DIN985 M8 FLAT WASHER DIN125 M8 RIN-433 SWIVELING CASTOR Ø80 SCREW DIN603 M8X45 SCREW DIN603 M6X70 RIN-431 LEG LEVELLER M16X102 with rubber pad FLAT WASHER DIN125 M6...
  • Page 66 GAELCO - RING RIDERS 10.10 PLATFORM - MAIN ASSEMBLIES CODE DESCRIPTION BIKE ASSEMBLY SWIVELING MACHANISM - TOP SWIVELING MECHANISM - BOTTOM PROTECTION BAR ASSEMBLY PLATFORM ASSEMBLY...
  • Page 67 GAELCO - RING RIDERS 10.11 PLATFORM - PROTECTION BAR CODE DESCRIPTION FLAT WASHER DIN125 M8 SPRING WASHER DIN127 M8 SCREW DIN912 M8X60 RIN-845 PROTECTION BAR RIN-886 PLASTIC COVER, 4” loudspeaker SCREW 3.9X13 RIN-846 METALLIC COVER, loudspeakers SCREW UM1101 M5X10 4” LOUDSPEAKER, 4 Ω / 60W...
  • Page 68 GAELCO - RING RIDERS 10.12 BIKE ASSEMBLY – DESIGN RELATED PARTS CODE DESCRIPTION RIN-809 REAR COVER, handle RIN-811 REAR PLASTIC ASSEMBLY, exhaust pipe & brake light RIN-812 REGISTER PLASTIC RIN-813 REGISTER STICKER SCREW UM1001 18X40 RIN-866 EXHAUST PIPE RIN-806 SIDE COVER - RIGHT...
  • Page 69 GAELCO - RING RIDERS...
  • Page 70 GAELCO - RING RIDERS 10.13 REAR PLASTIC CODE DESCRIPTION SNAP RIVET SR3075 RIN-884 BRAKE LIGHT - RIGHT RIN-883 BRAKE LIGHT - LEFT...
  • Page 71 GAELCO - RING RIDERS 10.14 BIKE ASSEMBLY – PARTS ON TOP CODE DESCRIPTION RIN-848 BRACKET, emergency stop button RIN-802b FUEL TANK COVER - REAR RIN-817 EMERGENCY STOP BUTTON RIN-819 START BUTTON - RED RIN-818 STICKER, emergency stop button RIN-816 VIEW BUTTON - GREEN...
  • Page 72 GAELCO - RING RIDERS 10.15A HANDLEBAR ASSEMBLY - BRAKE PARTS CODE DESCRIPTION RIN-312 BRAKE LEVER (components are not supplied separately) RIN-310 HANDLEBAR RIN-314 BRAKE CABLE RIN-318 LEVER STOPPER...
  • Page 73 GAELCO - RING RIDERS 10.15B HANDLEBAR ASSEMBLY - THROTTLE PARTS CODE DESCRIPTION RIN-320 THROTTLE ASSEMBLY (components are not supplied separately) RIN-310 HANDLEBAR RIN-315 THROTTLE CABLE...
  • Page 74 GAELCO - RING RIDERS 10.16 STEERING MECHANISM (SELECTED PARTS) CODE DESCRIPTION S40013406R10 SHAFT & BRACKET ASSEMBLY C-GA-RR02010 STOPPER C-11-404311 TRACTION SPRING C-09-11231 MICROSWITCH C-GA-RR06100 MAGNET IMA 10 SCA-N C-29-40RR10 SENSOR PCB S40013202301 DRIVE PULLEY C-GA-QU01030 BRACKET, steering motor C-29-401582 STEERING MOTOR - UJAQUE CC-1582/1...
  • Page 75 GAELCO - RING RIDERS...
  • Page 76 GAELCO - RING RIDERS 10.17 MOBILE STRUCTURE - TOP ASSEMBLY CODE DESCRIPTION RIN-835 UPPER PLATE RIN-839 BRACKET, protection folding hood LOCK NUT DIN985 M10 FLAT WASHER M10 SCREW UM1001 M6X10 LOCK NUT DIN985 M8 SPRING WASHER DIN127 M8 FLAT WASHER DIN125 M8...
  • Page 77 GAELCO - RING RIDERS...
  • Page 78 GAELCO - RING RIDERS 10.18 MOBILE STRUCTURE - FRONT FOOTREST ASSEMBLY DESCRIPTION CODE RIN-836 FOOTREST LOCK NUT DIN985 M8 FLAT WASHER DIN125 M8 RIN-837 LEVER RIN-860 RUBBER SCREW UM1001 M6X10 RUBBER SPRING RIN-858 STOPPER, polyamide RIN-857 SCREW 3,9X13 SPECIAL NUT...

  • Page 79: Vibrator Assembly

    GAELCO - RING RIDERS 10.19 VIBRATOR ASSEMBLY CODE DESCRIPTION GRUB SCREW DIN913 M6X20 RIN-823 ECCENTRIC FLYWHEEL SCREW UM1001 M5X12 RIN-841 BRACKET RIN-822 MOTOR, vibrator...
  • Page 80 GAELCO - RING RIDERS 10.20 MOBILE STRUCTURE - BOTTOM ASSEMBLY CODE DESCRIPTION RIN-851 PILLOW BLOCK UNIT UCP-207 RIN-877 PLASTIC PINION Z-80 with flat RIN-826 CIRCLIP DIN471 Ø13 RIN-850 GEARED POTENTIOMETER 5K RIN-841 CIRCLIP DIN471 Ø35 RIN-852 PILLOW BLOCK UNIT UCP-205...
  • Page 81 GAELCO - RING RIDERS...

  • Page 82: Platform Assembly

    GAELCO - RING RIDERS 10.21 PLATFORM ASSEMBLY CODE DESCRIPTION RIN-831 MAIN STRUCTURE RIN-832 COVER PLATE, aluminium SCREW UM1001 M6X10 RIN-850 GEARED POTENTIOMETER FLAT WASHER DIN125 M12 SPRING WASHER DIN127 M12 SCREW DIN933 M12X45 RIN-810 PROTECTION FOLDING HOOD SCREW UM1001 M6X16...
  • Page 83 GAELCO - RING RIDERS...

  • Page 84: Motor Assembly

    GAELCO - RING RIDERS 10.22 MOTOR ASSEMBLY CODE DESCRIPTION LOCK NUT DIN985 M16 SCREW DIN933 M10X70 FLAT WASHER DIN125 M10 RIN-827 CRANK, motor transmission WASHER DIN9021 M10 SPRING WASHER DIN127 M10 SCREW DIN933 M10X30 RIN-825 SWIVEL JOINT M14/M16 SBC-0385 NUT DIN934 M14...
  • Page 85 GAELCO - RING RIDERS 10.23 UNION HARNESS PROTECTION CODE DESCRIPTION RIN-441 LOCK NUT, conduit gland RIN-229 FIXING PLATE - CABINET SIDE RIN-440 CORRUGATED TUBE WITH CONDUIT GLANDS RIN-842 FIXING PLATE - PLATFORM SIDE...

  • Page 86: Wiring Diagrams

    GAELCO - RING RIDERS 11. WIRING DIAGRAMS 11.1 CABINET WIRING - 1...
  • Page 87 GAELCO - RING RIDERS 11.2 CABINET WIRING - 2...
  • Page 88 GAELCO - RING RIDERS 11.3 POWER (220ACV) & GROUND WIRING...
  • Page 89 GAELCO - RING RIDERS 11.4 PLATFORM WIRING...

  • Page 90: Chassis Wiring

    GAELCO - RING RIDERS 11.5 CHASSIS WIRING...
  • Page 91 GAELCO - RING RIDERS 12. CREDIT DISTRIBUTOR SETUP JP1:Not used JP2:Cabinet JP3:Coin controller JP4:Not used Connector JP2: This connector should be connected to ATV PCB wiring Description Values Source/Destination Pin 1 Input GND GND power supply Pin 2 Input VDC...
  • Page 92 GAELCO - RING RIDERS PROGRAMMING OF COIN CONTROLLERS Controllers supported: COIN CONTROL C-120 NRI G-13.6000 MARS CASHFLOW 330 MARS 330/S 212 NRI G-13.6000 Channel Channel Channel Channel Channel Channel Coin Control C 120 Coin 1 Coin 2 Coin 3 Coin 4...

  • Page 93: Application Examples

    GAELCO - RING RIDERS APPLICATION EXAMPLES Game price: 50c, NO BONUS Switch set up: Game price: 50c, BONUS FOR 2 ¤ (4 credits + 1 credit free) Switch setup: Game price: 1 ¤ , NO BONUS Switch setup: Game price: 1 ¤, BONUS FOR 2,5¤ (2 credits + 1 credit free)
  • Page 94 GAELCO - RING RIDERS SWITCH SETUP FOR OTHERS CURRENCIES SW1: Always OFF SW2: Coin multiplication factor SW2=OFF Chanel: Euro ¤, and rest of Europe Value: SW2=ON Chanel: (USA) Value: SW3: Not used SW4-SW5: Extra Credits (Bonuses) Combinations of these two dip switches are used to program bonuses (free games) according to the scale shown in the table.
  • Page 95 GAELCO - RING RIDERS APPLICATION EXAMPLES Example 1 Switzerland SW1 = SERIAL input. (5 FS via PIN 5) = (Channel 3) SW2 = Input values x1 x2 — x5 SW3 = Not used SW4 = EXTRA credit on the 20th pulse (=20FF)

Table of Contents