Advertisement

Quick Links

For your safety
Read these
instructions and the
accompanying safety
information carefully before
starting up the device and
starting work with the
device.
Keep these instructions in a
place that is accessible to all
users.
Safety information
This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given super-
vision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the
appliance.
Cleaning and user maintenance shall not be made by children wit-
hout supervision.
Warning! Electrical shock
If the device is faulty, active electrical conductors may be bare or the PE conductor may not
be functional.
Repairs must always be referred to a Weller-trained specialist.
If the electrical tool's power supply cord is damaged, this must be replaced with a specially
prefabricated power supply cord available through the customer service organisation.
Warning! Danger of injury
The device or parts of the device may fall off during transportation.
Hold the device by the intended handles only.
Never use the device as a means of transportation.
Warning! Danger of asphyxiation, Danger of poisoning
Improper installation can result in above-normal workplace concentrations
Measure the workplace concentration upon completion of installation work
Inappropriate maintenance cycles for gas media may result in above-normal workplace
concentrations
Specify maintenance cycle
Above-normal contamination levels in the ambient air during cleaning work on the pipe
system/extraction area
If suction capacity is impaired by build-up within the pipe system, replace the contaminated
parts
Thank you for the confidence you have shown in buying this device.
The device has been manufactured in accordance with the most rigo-
rous quality standards which ensure that it operates perfectly.
These instructions contain important information which will help you to
start up, operate and service the device safely and correctly as well as
to eliminate simple faults and malfunctions yourselves.
Always pass on the device to third parties together with these opera-
ting instructions.
The device has been manufactured in accordance with state-of-the-art
technology and acknowledged regulations concerning safety.
There is nevertheless the risk of personal injury and damage to property
if you fail to observe the safety information set out in the accompanying
booklet and the warnings given in these instructions.
19

Advertisement

Table of Contents
loading

Summary of Contents for Weller Zero Smog 4V

  • Page 1 If the device is faulty, active electrical conductors may be bare or the PE conductor may not be functional. Repairs must always be referred to a Weller-trained specialist. „ If the electrical tool‘s power supply cord is damaged, this must be replaced with a specially „...
  • Page 2: Specified Conditions Of Use

    BGETF). The efficiency test also serves to check for proper functioning of the WFE 2S / WFE 4S and Zero Smog 4V / Zero Smog 6V / Zero Smog 20T solder fume extractor systems. Use the supplied soft- ware CD.
  • Page 3: Technical Data

    „Warranty“. The warranty shall be void if damage is due to improper use and if the device has been tampered with by unauthorised persons. Subject to technical alterations and amendments. For more information please visit www.weller-tools.com...
  • Page 4: Menu Navigation

    SPEED 100 % VACUUM 60 % Default opera- ting mode MANUAL / AUTOMATIC Zero Smog 4V / 6V Submenu functions The speed (30-100%) can be To select a menu item, entered using the UP/DOWN press the Menu key. Each keys.
  • Page 5 Menu navigation FILTER TIME Reset filter time RESET Resets the elapsed filter opera- 5 sec ting hours to zero PRESSURE Pressure control / automatic speed control CONTROL 5 sec nur Zero When the extractor arm is open, Smog the required suction capacity 4V/ 6V / flow rate is set manually in the default operating mode by adjusting...
  • Page 6: Care And Maintenance

    Care and maintenance To ensure that the filtration system functions properly, the filter must Warning! be replaced as follows Before doing any work on at least once a year or „ the machine, pull the plug when indicated or „ out of the socket.
  • Page 7 Original declaration of conformity Solder fume extractor Zero Smog 4V Zero Smog 6V Zero Smog 20T We hereby declare that the products described herein comply with the following guidelines: 2011/65/EU (RoHS), 2004/108/EG, 2006/42/EG Applied harmonised standards: EN 55 014-1: 2012-05...
  • Page 8 Zero Smog 4V...
  • Page 9 Zero Smog 6V...
  • Page 10 Tel: +33 (0)1.64.43.22.00 Shanghai 201201 Australia Fax: +33 (0)1.64.43.21.62 Tel: +86 (21)60880288 Tel: +61 (2)6058-0300 Fax: +86 (21)60880289 Fax: +61 (2)6021-7403 www.weller-tools.com www.wellerft.com © 2015, Apex Tool Group, LLC. Weller® is a registered Trademark and registered Design of Apex Tool Group, LLC.

This manual is also suitable for:

Zero smog 6vZero smog 20t

Table of Contents