AMX NXT-BP Quick Start Manual

For more detailed installation and operating instructions, refer to the touch
panel's instruction manual, available on-line at www.amx.com.
NXT-CHG Modero Power Station
FIG. 1
Optional NXT-BP battery and NXT-CHG charger
Overview of the NXT-BP and NXT-CHG
The NXT-BP is a rechargeable Lithium-Ion "smart" battery used with the
Modero NXA-BASE/B Battery Base. This battery provides the user with an
on-board battery life indicator (FIG. 3).
The NXT-CHG Modero Power Station is a two bay, stand-alone battery
charger that is compliant with the Smart Battery System. This tabletop unit
can be used to recharge up to two NXT-BP batteries. The batteries are
charged in the order they are inserted into the NXT-CHG.
The NXT-CHG Slot 1 has the feature of being able to completely discharge
and recharge (Recalibrate) a battery. Refer to FIG. 2 for more information.
Specifications
Specifications
Dimensions (HWD):
NXT-BP • 0.69" x 3.50" x 5.81" (1.75 cm x 8.89 cm x 14.76 cm)
(FG2255-10)
NXT-CHG • 2.02" x 4.89" x 6.89" (5.13 cm x 12.42 cm x 17.50 cm)
(FG2250-50)
Power: • NXT-BP Battery Voltage - 11.1 Volts
• NXT-CHG: 90 - 264 VAC, 47-63 Hz, Single Phase
(using the included 24 VDC power supply)
Weight: • NXT-BP: 0.99 lbs (0.45 kg)
• NXT-CHG: 0.57 lbs (0.256 kg)
NXT-BP Features: • Battery Usage: 4 to 8 hours of continuous use (time is usage
dependant)
• Charge Capacity: 6300mAh
• Operating Environment: 10° C (50° F) to 35° C (95° F)
• Storage/Discharge Temperature: -20° C (-4° F) to +60° C (140° F)
NXT-CHG Features: • Charge Rate: 2.5 A @ 12 VDC
• 2-Bays: Sequential Charging
• LED: One LED indicator in front of each bay which conveys the status
of that bay. Refer to the Reading the NXT-CHG LED Indicator section
for more information.
• Recalibration Pushbutton: located between the bays to initiate
recalibration sequence in the left bay only.
• Charge time for two depleted batteries ~ 5 hours
• Recalibration Time: Less than 9 hours
Optional Accessories: • NXT-CHG Kit (FG2250-50K):
1 charger (FG2250-50) and 2 NXT-BP batteries (FG2255-10)
• NXT-BP batteries (FG2255-10)
• NXA-BASE/B Battery Base Kit (FG2255K)
1 battery base (FG2255) and 2 NXT-BP batteries (FG2255-10)
Powering the NXT-CHG
The NXT-CHG uses an included power supply to provide power for charging
the batteries.
1. Connect the terminal end of the included power supply to the rear of
the NXT-CHG Charger.
2. Provide power to the unit by connecting the other end (plug) into a
power socket that meets the requirements outlined in the
Specifications section for the NXT-CHG.
NXT-BP and NXT-CHG
NXT-BP Modero Power Pack
Modero Power Pack and Power Station
Reading NXT-CHG LED Indicator
FIG. 2 shows the front connectors on the NXT-CHG Modero Power Station.
Left Slot
(Slot 1)
Left Slot
LED
Recalibrate
Pushbutton
FIG. 2
Component locations on the NXT-CHG Modero Power Station
There is one LED indicator in front of each bay (FIG. 2) that conveys the
status of that bay as follows:
• Off: No battery detected
• Green Flashing: Fast charging
• Green Solid: Fully charged
• Yellow Flashing: Recalibration in process
• Yellow/Green: Recalibration complete
• Yellow Solid: Standby (waiting for other battery to charge)
• Red Flash: Error (problem with either the battery connection to the
internal slot or the battery itself)
Checking the NXT-BP Charge
1. Press the Battery Life Indicator button (FIG. 3) once to illuminate the
Battery Life LEDs and display the percent charge remaining on the
battery.
FIG. 3
NXT-BP Modero Power Pack (showing Battery Life Indicator and button)
2. Repeat these steps for the remaining NXT-BP battery.
3. Charge the batteries by inserting them within the battery charger.
Refer to the following section for more detailed information on this
process.
ATTENTION!
If the 25% LED indicator is blinking, this indicates there is less than 5% of a
charge remaining on the battery.
Quick Start Guide
Right Slot
(Slot 2)
Right Slot
LED
Battery Life (Charge)
Battery Life Indicator
button
Its recommended to
fully charge the
batteries before their
initial use