Summary of Contents for North Slope Chillers NSC0500
- Page 1 Freeze Owner’s Manual Page www.northslopechillers.com | (866) 826-2993 | 3130 S 1030 W, Suite 1 | Salt Lake City, UT 84119 Revised: 12/18/2020...
-
Page 2: Table Of Contents
Freeze Owner’s Manual Page Table of Contents Applications Cautions/Warnings Specification sheet Chiller Component Overview Installation User Interface Modifying Parameters Display Unit Thermostat Differential Upper and Lower limit of Thermostat Set Point Troubleshooting STANDARD PRODUCT WARRANTY 1. LIMITED WARRANTY 2. LIMITATION OF LIABILITY 3. -
Page 3: Applications
2 foot clearance at the back of the chiller 4. Flush chiller prior to use. North Slope Chillers tests every chiller on site prior to shipping. During testing North Slope Chillers uses a water/glycol mix to test their chillers. There will always be a small amount of water/glycol remaining in the system. -
Page 4: Specification Sheet
34"L x 65"W x 62"H North Slope Chillers tests every chiller on site prior to shipping. During testing North Slope Chillers uses a water/glycol mix to test their chillers. Since not all glycols are compatible with each other and vary by manufacture each chiller should be flushed with water for 10 minutes prior to use. -
Page 5: Chiller Component Overview
Page Chiller Component Overview NSC0500, NSC1000 and NSC2000 Models FRONT (NSC0500, NSC1000 and NSC2000 models) BACK (NSC0500, NSC1000 and NSC2000 models) www.northslopechillers.com | (866) 826-2993 | 3130 S 1030 W, Suite 1 | Salt Lake City, UT 84119 Revised: 12/18/2020... - Page 6 Freeze Owner’s Manual Page NSC5000 and NSC10000 Models FRONT (NSC5000 and NSC10000 models) BACK (NSC5000 and NSC10000 models) www.northslopechillers.com | (866) 826-2993 | 3130 S 1030 W, Suite 1 | Salt Lake City, UT 84119 Revised: 12/18/2020...
- Page 7 Freeze Owner’s Manual Page Fluid Circuit (NSC5000 and NSC10000 models) Electrical (NSC5000 and NSC10000 models) www.northslopechillers.com | (866) 826-2993 | 3130 S 1030 W, Suite 1 | Salt Lake City, UT 84119 Revised: 12/18/2020...
-
Page 8: Installation
Freeze Owner’s Manual Page Installation 1. Position chiller for use ● Place unit on a flat level surface in a well-ventilated area 2. Connect inlet and outlet fluid hoses ● Confirm hoses are connected to proper inlet and outlet ports 3. -
Page 9: User Interface
Freeze Owner’s Manual Page User Interface Set the Setpoint The display shows the current temperature Press "up/down" to access setpoint. Press "up/down" to adjust setpoint. After 30 seconds, the display automatically reverts to showing the current temperature. Or Press 2 x "Back" Modifying Parameters Display Unit Default Unit: Fahrenheit (°F). -
Page 10: Upper And Lower Limit Of Thermostat Set Point
Freeze Owner’s Manual 10 | Page Press “OK” Press "up/down" to find Press “OK” Press "up/down" to change parameter Press “OK” Upper and Lower limit of Thermostat Set Point Default Limits: Upper = 65°F, Lower = 25°F Press "up and down" and hold 5 seconds to access the menu. Press "up/down"... -
Page 11: Troubleshooting
Freeze Owner’s Manual 11 | Page Troubleshooting Symptoms Possible Cause(s) Compressor does not start. The temperature rises but 1. Compressor is not being powered the pump runs fine. 2. Flow switch is not activated Compressor hums but doesn’t start 1. Low line voltage 2. - Page 12 Freeze Owner’s Manual 12 | Page ● Suction pressure too low 2. Excessive refrigerant 3. Broke oil pump Fluid temperature too cold 1. Set point temperature is too low 2. Malfunctioning temperature controller 3. Malfunctioning temperature sensor 4. Leaking refrigerant solenoid valve Fluid flow fault 1.
-
Page 13: Standard Product Warranty
North Slope Chillers Product or for results of or damages caused to persons or property by the use of the North Slope Chillers Product. Only the Manufacturer is authorized to make any warranty or representation and the customer may not rely on any other warranty or representation. -
Page 14: Indemnification
Warranty. 4. INDEMNIFICATION Customer acknowledges that North Slope Chillers has no control over, and is not responsible for the manner in which the Customer uses the Product(s). The Customer hereby agrees to indemnify, defend and hold harmless (collectively, “indemnify”...