Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Dynamic TRE-75 TAMPING RAMMER
- Page 1 TRE-75 TAMPING RAMMER Operation manual Dynamic world Dynamic life...
-
Page 2: Table Of Contents
CONTENTS Contents....................1－1 Forward..................2－2 Feature...................2－2 Specification..................3－3 Safety....................3－4 Safety precautions................4－4 Transporting and storage..............4－6 Check before operation...............6－8 Starting the engine................8－10 Setting engine speed................10－11 Stopping the engine.................11－11 Preventative Maintenance and routine service plan ....12－18 Easy Troubleshooting..............19－20 Diagram...................21－28 - 1 -... -
Page 3: Feature
- which aim at improving our machines or their safety standards. FEATURE TRE-75 Tamping Rammer adopts the HONDA 4-cycles engine that there is one air cleaner. The guide handle offers a highly engineered, built-in shock mount system to reduce HAV (hand-arm vibration) and improve operator comfort. -
Page 4: Safety
Jump height: 50－60mm Forward speed: 8m/min Metal sheet: 280mm×350mm Power: ER12 Overall dimensions: 760mm×410mm×970mm Engine oil: Grade of Engine oil SF or SG; SAF10W－30 Engine oil: 0.30L Fuel: Unleaded gasoline with a pump octane rating of 90 or higher Fuel capacity: 3L Spark plug: NGK: CR5HSB;... -
Page 5: Safety Precautions
9. Do not uses to compacting severity harden or hard surface, such as block, floor slab, cement block. 10. Placed a machine, we should avoid dumping, roll and fall, etc. SAFETY PRECAUTIONS Gasoline is extremely flammable, and gasoline vapor can explode. Refuel outdoors, in a well-ventilated area, and keep other flames and sparks away. - Page 6 sure that no one be endangered by machines turning over by slipping or by moving machine parts. 3. Drain the used oil when being transported on vehicles, precautions have to be taken that vibration plates do not slip or turn over. The following should be taken to prepare your TRE-72 Tamping Rammer for extended storage.
-
Page 7: Check Before Operation
CHECK BEFORE OPERATION 1. Oil level check. CAUTIONS! Running the engine with a low oil level or without oil can cause engine damage. a. Remove the filler cap/dipstick and check the oil level shown on the dipstick. b. If the oil level is low, fill to the edge of the oil filler hole with the recommended oil. - Page 8 3. CHECK FUEL These engines are certified to operate on unleaded gasoline. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life. Never use stale or contaminated gasoline or an oil /gasoline mixture. Avoid getting dirt or water in the fuel tank. Occasionally you may hear a light “spark knock”...
-
Page 9: Starting The Engine
STARTING THE ENGINE （1）Open the fuel valve.（see Fig3-1） ① OPEN ② CLOSE （2）Tum the STOP SWITCH to the position “I”(ON).(see Fig 3-2) ① ON .的② OFF （3）Close the choke lever. FLOAT Type (see Fig 3-3-B) DIAPHRAGM Type (see Fig 3-3-B) ①... - Page 10 “compression” point. Return the handle to its original position and pull swiftly. Do not pull out the rope all the way. After starting the engine, allow the starter handle to return to its original position while still holding the handle. (See Fig 3-5) （...
- Page 11 SETING ENGINE SPEED （1）After the engine starts, set the speed control lever at MIN(low speed) position and warm it up without load for a few minutes. （2）Gradually move the speed control lever toward MAX(high speed) position and set it at the required engine speed. Whenever high speed operation is not required, slow the engine down ■...
-
Page 12: Stopping The Engine
NOTICE! A、Be careful to the machine weltered when the machine working on the abrupt surface. B、Turn the engine switch to the OFF position when stop working. C、Do not allow to the machine work on the severity harden surface. STOPPING THE ENGINE To stop the engine emergency, simply turn the engine switch to the OFF position. - Page 13 parts. a、Disassemble four lock-nuts between foot plate and pipe-protective, and then remove foot plate. b、Disassemble screws (M8×25) between foot plate and pipe-protective. c、Disassemble six screws (M12×35) among foot plate, cover and spring cylinder, then remove foot place. NOTICE ！ Do not to remove two screws (M12×25) between cover and spring cylinder when you operate step “c”.
- Page 14 ● Clean engine and check bolts (Daily) and nuts ● Check for leakage from hoses (Daily) and fitting ● (Refill Check and refill engine oil daily up to upper level) ● ● (Initial 20 Change engine oil hours) ● ● (Initial 20 Clean oil filter hours)
- Page 15 y2year ● Overhaul engine if necessary Tamping rammer： Each After month Every 6 Every year or 50 hrs months or or 300 hrs 150 hrs √ Check the oil lever sight plugs √ √ √ Check fastening screws √ √ √...
- Page 16 NOTICE！ Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take used oil in a sealed container to your local recycling center or service station for reclamation. Do not throw it in the trash, pour it on the ground, or pour it down a drain.
- Page 17 SPARK PLUGS NOTE Use the Plug Wrench supplied with this unit. （1）Clean off carbon deposits on the spark plug electrode using a plug cleaner or wire brush. （2）Check electrode gap. The gap should be 0.6mm to 0.7mm. Adjust the gap, if necessary, by carefully bending the side electrode. Recommended Spark Plug: CR5HSB (NGK) NOTICE！An incorrect spark plug can cause engine damage.
-
Page 18: Easy Troubleshooting
sealing washer is in poor condition, or if the electrode is worn heavy carbon build is found. 4、Measure the spark plug electrode gap with a wire-type feeler gauge. Correct the gap, if necessary, by carefully bending the side electrode. The gap should be: 0.6 - 0.7mm (0.024 - 0.028 in) 5、Check sealing washer, Install the spark plug carefully, by hand, to avoid cross-threading. - Page 19 1. Is there a strong spark across the electrode? （1）Is the stop switch at position “I” (ON)? （2）Remove and inspect the spark plug. If the electrode is fouled, clean or replace it with new one. （3）Remove the spark plug and connect it to the plug cap. Pull the starter handle while grounding spark plug against engine body.
- Page 20 (Check the fuel intake of the carburetor.) （4）In case the engine does not start with well supplied fuel, try using fresh fuel. 4 work machine jumping instability or no strength (1) work, when the ground is too hard, the machine will be beating is too large, or not stable, and the effect is not ideal.
-
Page 21: Diagram
DIAGRAME： 1. Handle Assembly： - 20 -... - Page 22 Item Part Drawing number Description 1001 GB/T5783-2000 Bolt M8×16 1002 GB/T93-1987 Gasket 8 1003 TRE75-22 Shock-mount 1004 GB/T5783-2000 ScrewM8×25 1005 GB/T70.2-2000 Screw M8×12 1006 TRE75-16 Guide handle 1007 VP1550-15-01 Rubber Block 1008 Kit-roller assembly 1009 GB/T6182-2000 Nut M6 1010 TRE75-16-01 Kit-roller 1011 GB/T70.1-2000...
- Page 23 2、Housing-crankcase Assembly： - 22 -...
- Page 24 Drawing number Item Part Description 2001 TRE75-20 Wave handle 2002 GB/T1235-1976 O-ring 11×1.9 2003 TRE75-19 Head cover 2004 TRE75-18 Shaft 2005 TRE75-32 Air cleaner 2006 TRE75-17 Screw 2007 TRE75-15 Gear-crank GB/T893.1-1986 2008 Retaining Ring 80 2009 GB/T276-1994 Bearing 6208 GB/T894.1-1986 2010 Retaining Ring 40 2011...
- Page 25 GB/T292-1964 2022 Bearing 6207 2023 HG4-692-67 Seal PD40×62×12 2024 GB/T1235-1976 O-ring 75×3.1 2026 TRE75-31 Tube A 2025 TRE75-33 Clamp 2027 TRE75-09 Clutch assembly 2028 TRE75-09-06 Washer 2029 TRE75-09-04 Spring 2030 TRE75-09-05 Clutch 2031 TRE75-09-03 Centric 2032 TRE75-09-02 WasherⅡ 2033 TRE75-09-01 WasherⅠ...
- Page 26 3.Guide Assembly： - 25 -...
- Page 27 Item Part Drawing number Description 3001 GB/T10-1988 Bolt M10×60 3002 GB/T10-1988 Bolt M12×80 3003 GB/T10-1988 Bolt M12×65 3004 TRE75-01-01-02 Metal sheet 3005 TRE75-01-01-03 Wooden sheet 3007 GB/T95-1985 Washer10 3008 GB/T6182-2000 Nut M10 3009 TRE75-01-01 Rammer assembly 3013 TRE75-01-01-01 Kit-roller 3014 GB/T95-1985 Washer12 3015...
- Page 28 3028 TRE75-01-04 Spring cylinder 3029 TRE75-26 3030 TRE75-10 Pin-piston mount 3031 TRE75-05 Pressure lever 3032 TRE75-06 Dustproof box 3033 GB/T5783-2000 BoltM10×30 3034 GB/T39-1988 Square nut 3035 TRE75-25 Clamp 3036 GB/T70.1-2000 Screw M10×30 3037 GB/T93-1987 Gasket10 3038 GB/T95-1985 Washer10 3039 TRE75-08 Guide cylinder 3040 GB/T1235-1976...
- Page 29 - 28 -...
- Page 30 - 29 -...
- Page 31 - 30 -...
- Page 32 We provide below machines CONCRETE PROCESSING SCREED POWER TROWEL RIDE-ON POWER TROWEL CONCRETE CUTTER CONCRETE VIBRATOR VIBRATOR POKER POLISHING MACHINE FLOOR GRINDER ROAD PLANER ASPHALT & CLAY COMPACTION RIDE-ON ROLLER VIBRATORY ROLLER LIGHT TOWER PLATE COMPACTOR REVERSIBLE PLATE TAMPING RAMMER MORTAR CONVEYING &...
Need help?
Do you have a question about the TRE-75 TAMPING RAMMER and is the answer not in the manual?
Questions and answers
My tre75 works only for 2mins powerfully then stops engine starts easily if i disconect enginne from rammer it can run at full throttle continously without stopping so i suspect the problem is in that leg i have never opened it befor what can be faulty there and what precautions can i take