Table of Contents

Advertisement

Quick Links

myAVR
myAVR
myAVR
myAVR
mySmartUSB Version 2.11
Inhalt
Allgemeine Beschreibung............................................... 3
Überblick ........................................................................ 3
Eigenschaften............................................................. 3
Technische Daten .......................................................... 4
Betriebsdaten ............................................................. 4
Maximalwerte ............................................................. 4
Schnittstellendaten ..................................................... 4
Mechanische Daten ....................................................... 4
Funktionsschema ........................................................... 5
DIP-Schalter und Betriebsmodi ...................................... 6
Standardeinstellung der DIP-Schalter......................... 6
LED Statusanzeige..................................................... 6
RESET des Adapters.................................................. 7
Enable Power ............................................................. 7
Firmware Update ........................................................ 7
USB Treiberinstallation................................................... 8
Der USB Controller von mySmartUSB........................ 8
Download des Treibers............................................... 8
Deinstallieren des alten Treibers ................................ 8
Installation des neuen Treibers................................... 8
Aufräumen .................................................................. 9
Softwareeinstellungen.................................................. 10
Anwendung mit AVRDUDE ...................................... 12
Das mySmartUSB Protokoll...................................... 13
Allgemeine Sicherheitshinweise................................... 14
Anwendungsbeispiele .................................................. 14
www.myAVR.de
Technische Beschreibung
technical description
Contents
General Description ....................................................... 3
Overview ........................................................................ 3
Properties ................................................................... 3
Technical Data ............................................................... 4
Operating Data ........................................................... 4
Maximum Values ........................................................ 4
Interface Data ............................................................. 4
Mechanical Data ............................................................ 4
Functional Diagram ........................................................ 5
DIP-Switches and Operating Modes .............................. 6
default setting of the DIP-Switches............................. 6
LED Status indicator................................................... 6
RESET of the adapter ................................................ 7
Enable Power ............................................................. 7
Firmware update......................................................... 7
USB driver installation.................................................... 8
The USB Controller of mySmartUSB.......................... 8
Download the driver.................................................... 8
Uninstall the old driver ................................................ 8
Installation of the new driver ....................................... 8
Clean up ..................................................................... 9
Software settings.......................................................... 10
Use with SiSy (from version 2.17e) .......................... 10
Use with myAVR Workpad Version 1.2 .................... 10
Use with AVR Studio Version 4.12.498 .................... 11
Use with AVRDUDE ................................................. 12
Use with CodeVision Version 1.25.5 ........................ 12
The mySmartUSB protocol....................................... 13
Safety Guidelines ......................................................... 14
Examples of use........................................................... 14
© Laser & Co. Solutions GmbH - 07/2007
www.myAVR.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the mySmartUSB and is the answer not in the manual?

Questions and answers

Summary of Contents for myAVR mySmartUSB

  • Page 1: Table Of Contents

    Anwendung mit SiSy (ab Version 2.17e) ....10 Use with SiSy (from version 2.17e) ......10 Anwendung mit dem myAVR Workpad Version 1.2 . 10 Use with myAVR Workpad Version 1.2 ....10 Anwendung mit dem AVR Studio Version 4.12.498 . 11 Use with AVR Studio Version 4.12.498 ....
  • Page 2 Seite: 2/14 Technische Beschreibung mySmartUSB Version 2.10 Die Informationen in diesem Produkt werden ohne Rück- sicht auf einen eventuellen Patentschutz veröffentlicht. Warennamen werden ohne Gewährleistung der freien Verwendbarkeit benutzt. Bei der Zusammenstellung von Texten und Abbildungen wurde mit größter Sorgfalt vorgegangen.
  • Page 3: Allgemeine Beschreibung

    It provides specific options to connect it schlussfertiges Modul in SMD-Bauweise. Er verfügt über to our myAVR USB boards or to Standard-ISP. For commu- spezielle Anschlussoptionen für das myAVR Board 2 USB nication with the PC it uses a virtual COM-Port. This means, und Standard-ISP.
  • Page 4: Technische Daten

    Seite: 4/14 Technische Beschreibung mySmartUSB Version 2.10 Technische Daten Technical Data Betriebsdaten Operating Data Versorgungsspannung 5 V über den USB-Bus Supply Voltage 5 V via USB bus 10-50 mA typical without other 10-20 mA typisch ohne weitere Verbraucher loads Betriebsstrom...
  • Page 5: Funktionsschema

    POWER UART UART ISP-Port / ISP-port USB–Anschluss / USB interface Interface zum myAVR Board 2 USB / interface to the myAVR Board 2 USB Status LED’s Controller / ISP Leiste links / interface left Leiste rechts / interface right...
  • Page 6: Dip-Schalter Und Betriebsmodi

    • Stumm • quiet Hinweis: Die beschriebenen Modi funktionieren nur im Notice: The described modi work only with the myAVR Zusammenhang mit dem myAVR Board 2. Für Fremdsys- Board 2. For third-party systems you can use the mySmar- teme kann mySmartUSB als AVR 910 kompatibler Pro-...
  • Page 7: Reset Des Adapters

    Technische Beschreibung mySmartUSB Version 2.10 Seite: 7/14 RESET des Adapters / RESET of the adapter • DIP 4 kurz ON/OFF schalten • switch DIP 4 ON/OFF • danach wieder Standardeinstel- • restores the default settings 4 3 2 1 lung...
  • Page 8: Usb Treiberinstallation

    COM-Port benutzt werden. Please note: Beachte: mySmartUSB must not be connected to your computer Der mySmartUSB darf vor der Installation der Treiber nicht while installing the driver. angeschlossen werden. For installation you need administration rights. Für die Installation benötigen Sie Administratorrechte.
  • Page 9: Anschließen Des Mysmartusb (Mysmart Control)

    Benutzen des mySmartUSB (mySmart Control) Use of mySmartUSB (mySmart Control) Der mySmartUSB kann jetzt als serieller Programmer oder mySmartUSB can be used either as serial programmer or als USB UART Bridge über den zugewiesenen virtuellen as USB UART bridge. On Microsoft Windows virtual COM- COM Port genutzt werden.
  • Page 10: Softwareeinstellungen

    Anwendung mit SiSy (ab Version 2.17e) Use with SiSy (from version 2.17e) Bei der Anwendung mit SiSy sind auf jedem Programmob- If you want to use mySmartUSB with SiSy you need to jekt (kleines Programm, Programmablaufplan, Klassendia- change the following settings for each programming object gramm) über den Dialog „Definieren“...
  • Page 11: Anwendung Mit Dem Avr Studio Version 4.12.498

    AVR-Prog is looking only at the COM-Ports 1 to 4. If the bis 4. Sollte der virtuelle COM-Port des mySmartUSB virtual COM-Port of mySmartUSB is higher then 4 AVR höher liegen findet das AVR Studio den Programmer nicht. studio will not find it. In this case you need to select a valid In dem Fall muss über die Systemsteuerung ein für das...
  • Page 12: Anwendung Mit Avrdude

    Seite: 12/14 Technische Beschreibung mySmartUSB Version 2.10 Anwendung mit AVRDUDE Use with AVRDUDE AVRDUDE ist eine Konsolenanwendung. Die Parameter- AVRDUDE is a command-line tool. The parameter line for zeile für AVRDUDE sollte wie folgt aussehen: AVRDUDE should look as follow: C:\Programme\winavr\bin\avrdude.exe -p ATmega8 -e -c avr910...
  • Page 13: Das Mysmartusb Protokoll

    Die Firmware des mySmartUSB verfügt neben den Besides the standard AVR910 and AVR911 protocols the AVR910 und AVR911 spezifischen Protokollen über ein firmware of the USB programmer mySmartUSB uses its eigenes Protokoll um die zusätzlichen Funktionen des own protocol to perform additional tasks. The mySmar- mySmartUSB anzusprechen.
  • Page 14: Allgemeine Sicherheitshinweise

    Technische Beschreibung mySmartUSB Version 2.10 Allgemeine Sicherheitshinweise Safety Guidelines Grundsätzlich ist mySmartUSB nur zum Einsatz unter Lern- mySmartUSB is designed for educational and experimental und Laborbedingungen konzipiert. Er ist nicht vorgesehen use only. It is not intended and not dimensioned to control und nicht dimensioniert zur Steuerung realer Anlagen.

Table of Contents