Summary of Contents for Maximum 5111
- Page 2 TABLE OF CONTENTS TECHNICAL SPECIFICATIONS SAFETY INSTRUCTIONS IMPORTANT INFORMATION SYMBOL PARTS LIST KNOW YOUR TOOL OPERATING INSTRUCTIONS MAINTENANCE WARRANTY NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-888-670-6682. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions.
- Page 3 (cordless) power tool. DEPTH OF CUT AT 90° 2 1/4" (5.6 cm) WORK AREA SAFETY DEPTH OF CUT AT 45° 1 19/32" (4.1 cm) COMPATIBLE MAXIMUM BATTERY 054-3203-2 (2.0 Ah) (SOLD SEPARATELY); ® Cluttered or dark areas invite accidents. •...
- Page 4 model no. 054-8355-0 | contact us 1-888-670-6682 PERSONAL SAFETY power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. • Stay alert, watch what you are doing and use common sense when operating a Properly maintained cutting tools with sharp •...
- Page 5 model no. 054-8355-0 | contact us 1-888-670-6682 Charging • When the blade is pinched or jammed tightly by the kerf closing down, the blade tool outside the temperature range specified in the instructions. stalls and the motor reaction drives the unit rapidly back toward the operator. improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
- Page 6 model no. 054-8355-0 | contact us 1-888-670-6682 Lower guard function Operator Prevention of Kickback and Kickback • Check the lower guard for proper closing before each use. Do not operate saw • Air vents often cover moving parts and should be avoided. Loose clothes, Never clamp or tie the if lower guard does not move freely and close instantly.
- Page 7 The length of service from your battery will depend on the type of work you battery. are doing. The battery has been designed to provide maximum trouble-free life. • The charger is designed to operate on standard household electrical power (120 V~).
- Page 8 model no. 054-8355-0 | contact us 1-888-670-6682 SYMBOL No. Description No. Description Some of the following symbols may be used on this tool. Please study them and learn Front handle Lower guard arrow their meaning. Proper interpretation of these symbols will allow you to operate the tool Lock-off button Blade bolt better and more safety.
- Page 9 model no. 054-8355-0 | contact us 1-888-670-6682 No. Description No. Description Hex wrench 0° cutting support Spindle lock Depth adjusting lever Bevel scale Remaining power indicator Bevel scale pointer...
- Page 10 model no. 054-8355-0 | contact us 1-888-670-6682 INTENDED USE NO. DESCRIPTION NO. DESCRIPTION LEFT HOUSING SCREW This circular saw is designed for wood cutting applications. SPRING SCREW use under wet conditions or in presence of DO NOT LOCK-OFF BUTTON flammable liquids or gases. TRIGGER SWITCH SPINDLE LOCK BUTTON SCREW...
- Page 11 model no. 054-8355-0 | contact us 1-888-670-6682 • When the charger detects a malfunction in the battery, two charging lights will blink CHARGING PROCEDURE at the same time. Please remove the battery and allow it to cool down for 15—30 •...
- Page 12 model no. 054-8355-0 | contact us 1-888-670-6682 TEMPERATURE CUT OUT • Slide the lower guard lever up to raise the lower guard (Fig. I). Remove the blade from the spindle. Always clean the When used as intended, the circular saw cannot be subject to overload. But running spindle, upper guard and lower guard to remove any dirt continuously at full load for a long time will cause the battery pack to overheat.
- Page 13 model no. 054-8355-0 | contact us 1-888-670-6682 loosen the bevel adjusting knob (Fig. N). Please refer to the table below to determine the correct size replacement blade for your model saw. Only use 6 1/2” (165 mm) saw blades with 5/8” (15.9 mm) arbour holes. •...
- Page 14 model no. 054-8355-0 | contact us 1-888-670-6682 (FIG. S) DO support board or panel NEAR the cut. (FIG. T) DON’T support board or panel AWAY from the cut. • Line up the kerf indicator with your cutting line. Position your arms and body to resist kickback.
- Page 15 model no. 054-8355-0 | contact us 1-888-670-6682 KICKBACK 4. MATERIALS THAT REQUIRE EXTRA ATTENTION Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing • Wet lumber. an uncontrolled saw to lift up and out of the workpiece toward the operator. When the •...
- Page 16 WASTE DISPOSAL The batteries in this tool have been designed to provide maximum trouble-free life. Like all batteries, they will eventually wear out. Do not disassemble the battery pack The product must not be discarded with normal household waste.
- Page 17 This MAXIMUM product is guaranteed for a period of 5 years from the date of original have repaired or replaced them;...
- Page 18 In addition to the 5-Year Limited Warranty, this MAXIMUM product is covered by our: 1-YEAR REPAIR WARRANTY Maximum Canada will maintain this product and replace critical parts which have worn beyond reasonable use through normal use of such product, any time during the first year after purchase.
Need help?
Do you have a question about the 5111 and is the answer not in the manual?
Questions and answers