Advertisement
Optical
tube
Rear
cell
Optional
extension
rings
optional Astro-Tech 3.7" diameter extension rings (available in both
1" and 2" lengths) thread in place securely to provide a very strong
and rigid mount that holds the focuser at the proper spacing from the
scope body to suit your particular camera's requirements.
Two 2" #AT2EXT extensions or a combination of one 2" and one or
two 1" #AT1EXT extensions will generally be needed for imaging
with webcams and DSLRs. Knowing the distance from the front of
your camera adapter to the camera's focal plane and a little calculation
beforehand will quickly determine what combination of optional
extension rings will be needed for your particular imaging setup.
Be careful not to cross-thread any of the focuser extension
rings when and if changing them in the dark.
The Crayford Focuser: The backlash-free focuser has dual-speed
focusing. There are two coarse focusing knobs. The right knob also
has a smaller concentric knob with a 10:1 reduction gear for microfine
focusing. This provides very precise image control during high power
visual observing and critical DSLR imaging. The focus knobs have
ribbed gripping surfaces so they are easy to adjust, even while wear-
ing gloves or mittens in cold weather.
There are two chrome lock knobs on the underside of the focuser,
as shown in the illustration below. The rear knob (closest to the ob-
server) adjusts the tension on the Crayford focuser to accommodate
different weight equipment loads without focuser slippage. The rear
tension knob should always be tightened firmly, even with a
light equipment load, to avoid drawtube flexure.
The front knob (closest to the scope) locks the focuser drawtube
firmly in place (disengaging the focusing knobs) once the correct
photographic focus has been reached.
AT6RC FOCUSER LOCK KNOBS
Rotating the Focuser: The AT6RC focuser can be rotated a full
360° for the best photographic composition prior to critical focusing,
or to put your star diagonal in the most comfortable visual observing
position. To rotate the focuser, loosen the ribbed locking collar con-
necting the focuser to the telescope rear cell or extension ring by
turning the collar slightly counterclockwise. Adjust the focuser to the
desired angle, and then firmly tighten the collar back in the opposite
direction to lock the focuser at the new angle.
astro-tech
from Astronomy Technologies, 680 24th Avenue SW, Norman, OK 73069
© 2010 by Astronomy Technologies
THE PARTS
OF THE AT6RC
FOCUSING
SYSTEM
Crayford
focuser
Rear lock knob:
adjusts drawtube tension
Front lock knob:
locks drawtube in place
Ribbed locking collar:
locks focuser rotation and
allows focuser removal
Specifications, features, and descriptions are effective 7/1/2010, but are subject to correction and/or modification without notice and/or obligation.
Mounting Your AT6RC: The underside of the AT6RC has a 12.75"
long Vixen-style dovetail bar running from front cell to rear cell. This
will let you mount your AT6RC on any equatorial mount using a Vixen-
style dovetail. You can also piggyback it on a larger scope using any
accessory mounting system (such as those from Losmandy) that has
a Vixen-style dovetail. The long length of the dovetail bar makes it
easier to balance the AT6RC and varying equipment loads. An op-
tional Vixen-style dovetail #AT6SDP is available for installation on top
of the AT6RC. This lets you install a photoguide scope on top of the
optical tube when using the AT6RC as your primary scope.
Finderscope: No finderscope is provided, due to the primarily
photographic nature of the AT6RC. However, a mounting shoe is pro-
vided on the rear cell that will hold an optional Astro-Tech #ATF non-
magnifying illuminated multireticle finder, or any similar finder or
photoguide ring system that uses a Vixen-style mounting shoe.
Caring for Your Scope Finish: The AT6RC uses automotive-
grade paints and anodized components. These very durable surfaces
can become smudged with fingerprints during use, but these will not
harm the finish. A little moisture from your breath and a quick wipe
with a clean handkerchief is generally enough to remove the finger-
prints. Avoid harsh chemical cleaners or organic solvents like ben-
zene, alcohol, etc., as these may ruin the finish.
Cleaning Your Scope Optics: Because of the positioning of the
mirrors within the optical tube, they will rarely (if ever) need clean-
ing. Small amounts of dust will not appear in the image or block
enough light to be an issue and can be safely ignored. If you abso-
lutely feel you must clean the optics, however, it can be done at your
own risk. You will have to disassemble the optical tube to do it, so it
is not something that should be undertaken lightly.
SCREWS HOLDING REAR CELL TO OPTICAL TUBE
Rear cell
Front
dovetail
screws
(one pair)
Optical
tube
Referring to the illustration above, with the nose of the scope rest-
ing on a flat surface, start by undoing the four screws that hold the
dovetail to the optical tube. Remove the dovetail. Set the four screws
aside so you don't mix them up with the other rear cell hardware.
Use two small pieces of masking tape to mark the position of the
rear cell in relation to one of the optical tube screw holes so you can
reassemble the rear cell and tube in its original radial orientation.
Remove the remaining four rear cell screws to release the rear cell
and lift it straight up and out of the optical tube.
Any damage to the AT6RC sustained during an attempt to
disassemble and clean the optics is not covered by warranty.
Collimating Your AT6RC Optics: Your Astro-Tech AT6RC Ritchey-
Chrétien's primary and secondary mirrors were collimated at the fac-
tory before being shipped. Nevertheless, rough treatment in transit
could potentially cause the secondary mirror to be knocked out of
collimation, and rough and bumpy roads during trips to a dark sky
observing site might require minor tweaking of the collimation. The
optical axis of the primary mirror/baffle tube assembly is less likely to
be knocked out of collimation, but is also capable of being collimated
if needed. If collimation of your AT6RC is needed, refer to the sepa-
rate "Collimating an Astro-Tech AT6RC" instruction sheet.
www.astronomytechnologies.com
Mirror collimation
screws: six total in
three pairs (see
separate collimation
sheet)
Dovetail /rear cell
screws (one pair)
Rear cell screws (six total: two
on top; two on bottom through
the dovetail and holding it in
place; plus one on each side)
Advertisement
