Perenio PEKIT01 Installation And Operation Manual

Smart security kit

Hide thumbs Also See for PEKIT01:

Quick start manual (25 pages)

Connection manual (8 pages)

Manual (12 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

Installation and Operation Manual

for Perenio® PEKIT01

Smart Security Kit

July, 2020

Table of Contents

Summary of Contents for Perenio PEKIT01

Page 1 Installation and Operation Manual for Perenio® PEKIT01 Smart Security Kit July, 2020...
Page 3: Introduction
Introduction The Perenio Smart Security Kit is specially designed to detect potentially dangerous situations in the area or your interest. It is used as a part of a reliable Perenio Smart Building Management System. The Control Gateway allows the User to monitor and manage operation of all connected ZigBee devices without passing commands to third party servers.
Page 4: Responsibility And Technical Support
Perenio IoT reserves the right to modify the device and make corrections or changes to this document without prior notice of the User, and shall not be responsible for any...
Page 5: Conformance To Standards
Details on available Certificates are specified in Section 6 of the present document. For copies of Certificates and Reports, please visit a corresponding Section at perenio.com. BG CZ ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 5 of 69...
Page 6: Table Of Contents
1.5.2 Technical Specification ..............28 1.5.3 Scope of Delivery ................30 1.6 Packaging and Labelling ................ 30 1.7 Safe Operation Rules ................31 1.8 Why ZigBee ..................31 Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 6 of 69...
Page 7 Figure 4 – PECSS01 Smoke Sensor Exterior ............15 Figure 5 – PECSS01 Smoke Sensor Buttons and Indicators .........15 Figure 6 – Scope of Supply of the PECSS01 Smoke Sensor ........18 ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 7 of 69...
Page 8 Table 6 – Basic Technical Specifications of the Motion Sensor ......28 Table 7 – Data on separately supplied CG and Sensors ........31 Table 8 – Typical Errors and Troubleshooting Methods ........65 Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 8 of 69...
Page 9 Perenio® PEKIT01 Smart Security Kit Connection to the Perenio Smart Mobile App A. INSTALLATION OF THE PERENIO SMART MOBILE APP ........36 B. DEVICE ACTIVATION BY QR CODE SCANNING ..........38 C. SENDING WI-FI NETWORK DATA TO THE DEVICE ..........39 D. LOCATION AND ROOM SETTING ..............40 E.
Page 10: General Description And Specifications
1.1 PEACG01 Control Gateway 1.1.1 General Purpose The Perenio® PEACG01 Control Gateway (hereinafter referred to as the CG) is designed to join operation of ZigBee devices within the Perenio Smart Building Management System, as well as to collect data and alert Users in the event of alarm.
Page 11: Figure 1 - The Peacg01Control Gateway Exterior
It lights up in the case of connection via the Ethernet Cable Power Indicator It lights up in the case of connection to the mains Power Button The button used to power on/off the Control Gateway ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 11 of 69...
Page 12: Technical Specification
802.11b (11Mbps max), 802.11g (54Mbps max), 802.11n (300Mbps max), 802.15.4 (250Kbps) WEP/WPA2 Encryption Support of 128-bit encryption Supported Protocol TCP/IP IoT Protocols MQTT and CoAP Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 12 of 69...
Page 13 Casing Material PC (Polycarbonate) White Color Dimensions (L x W x H) 110 x 110 x 31 mm Weight 123.7 g (259 g with accessories) ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 13 of 69...
Page 14: Scope Of Delivery
The Perenio® PECSS01 photoelectric sensor is a ZigBee-based device intended to detect smoke and its visible particles (flameless stage). This device is used as part of the Perenio® Building Management System and provides for timely alert in the event of smoke in the room.
Page 15: Figure 4 - Pecss01 Smoke Sensor Exterior
– PECSS01 Smoke Sensor Exterior Figure 4 Reset Button Mounting Bracket Test Button/ Indicator Siren Smoke Detector – PECSS01 Smoke Sensor Buttons and Indicators Figure 5 ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 15 of 69...
Page 16: Technical Specification
Repeater: N/A Alarm Indication Red LED Alarm Type Siren, light indication Alarm Level up to 85dB (at a distance of 3 meters) Sensitivity 0.089dB/m to 0.25dB/m Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 16 of 69...
Page 17: Scope Of Delivery
24 months Certification CE, EAC, RoHS, UA.TR 1.2.3 Scope of Delivery The following items and accessories are supplied within the Perenio® PECSS01 Smoke Sensor package: 1. PECSS01 Smoke Sensor (1 pc.) 2. Battery (CR123A) (1 pc.) 3. Screws and dowels (1 set) 4.
Page 18: Pecls01 Leak Sensor
1.3 PECLS01 Leak Sensor 1.3.1 General Purpose The Perenio® PECLS01 Leak Sensor is a device intended to alert users in the case of flood in the room. This device is used as part of the Perenio® Building Management System and is suitable for detection of leakage of water and some other liquids in the place of its installation.
Page 19: Figure 7 - Pecls01 Leak Sensor Exterior
Leak Sensor to be detected by the Control Gateway Leak Detectors The Sensor will be actuated in the case when both detectors will be covered with water or other liquids ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 19 of 69...
Page 20: Technical Specification
Storage Humidity 20°C to +93°C RH On a horizontal surface (For indoor installation). For outdoor installation, operating temperature and Installation humidity conditions shall be respected Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 20 of 69...
Page 21: Scope Of Delivery
24 months Certification CE, EAC, RoHS, UA.TR 1.3.3 Scope of Delivery The following items and accessories are supplied within the Perenio® PECLS01 Leak Sensor package: 1. PECLS01 Leak Sensor (1 pc.) 2. Battery (CR123A) (1 pc.) 3. Quick Start Guide (1 pc.) 4.
Page 22: Pecws01 Door & Window Sensor
The PECWS01 magnetic sensor is a device that sends corresponding signals to the Perenio® Control Gateway when the magnet is moved away from the main part of the device to a distance of more than 20-30 mm or is returned back to initial state.
Page 23: Technical Specification
Reset Button Side panel of the Sensor Standalone Operation Power Type CR2032 Battery (125mAh, 3V), 1 pc. Power Consumption Standby Mode: not more than 0.0016mA ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 23 of 69...
Page 24: Scope Of Delivery
24 months Certification CE, EAC, RoHS, UA.TR 1.4.3 Scope of Delivery The following items and accessories are supplied within the Perenio® PECWS01 Door & Window Sensor package: 1. PECWS01 Door & Window Sensor (1 set) 2. Battery (CR2032) (1 pc.) 3.
Page 25: Pecms01 Motion Sensor
1.5.1 General Purpose The Perenio® PECMS01 Infrared Motion Sensor is a PIR device that detects movement of thermal objects in the desired area and sends an alarm to the Perenio® Control Gateway. The PECMS01 Motion Sensor has a number of distinctive features, namely: ...
Page 26: Figure 13 - Pecms01 Motion Sensor Exterior
– PECMS01 Motion Sensor Exterior Figure 13 Indicator Mounting Panel PIR Sensor Reset Button Delay Switch Night Mode Switch Battery Cover – PECMS01 Motion Sensor Components Figure 14 Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 26 of 69...
Page 27 (if smart bulbs connected). The following delay periods are possible:  1, 5 or 10 minutes. Battery Cover It protects the battery from external effects ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 27 of 69...
Page 28: Technical Specification
10% to 85% (non-condensing) Storage Temperature -10°C to +50°C Storage Humidity 10% to 95% (non-condensing) On a flat vertical surface (For indoor installation only). Installation Casing Material ABS/PC Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 28 of 69...
Page 29: Figure 15 - Detection Angles Of The Pecms01 Motion Sensor
15-b – Detection angle (vertically) Sensor Detection Area 15-c – Details on the vertical detection angle – Detection Angles of the PECMS01 Motion Sensor Figure 15 ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 29 of 69...
Page 30: Scope Of Delivery
* Images of accessories are provided for informational purposes only 1.6 Packaging and Labelling The Perenio® PEKIT01 Smart Security Kit is supplied in an individual carton package of 292 x 176 x 71 mm (L x W x H) containing the full name and marking of the device, the list of accessories provided and basic technical specifications thereof, as well as the date of manufacture and information about the Manufacturer of devices.
Page 31: Safe Operation Rules
43 g/70 g 1.7 Safe Operation Rules For the proper and safe operation of Perenio® PEKIT01 Smart Security Kit, follow the instructions and safety procedures described in the present Manual. The Manufacturer shall not be liable for any damage caused as a result of improper operation of devices.
Page 32: Figure 17 - Self-Recovery Of The Zigbee Network
Possibility of expanding the network to 65,000 devices;  Data exchange rate of up to 250kbps. NOTE. Sensors and other battery-powered Perenio® devices do not have a signal repeating function. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved...
Page 33: Standalone Operation Of Perenio® Sensors
PEKIT01 Smart Security Kit 1.9 Standalone Operation of Perenio® Sensors The Control Gateway shall not be deemed mandatory for all Perenio® Sensors operation and notification of Users of potentially dangerous situations. Thus, the Smoke Sensor and the Leak Sensor can operate as standalone devices, i.e.
Page 34: Installation And Setup
ZigBee devices. Below see possible locations for devices. – Examples of installation of the CG and the Door & Window Sensor* Figure 18 Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 34 of 69...
Page 35: Figure 19 - Examples Of Installation Of The Leak And Motion Sensors
Activation of the Control Gateway via the Mobile App;  Switching on the Sensor and installation in the required place;  Connection of the Sensor to the Control Gateway. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 35 of 69...
Page 36: Initial Installation And Configuration Of The Control Gateway
2. Install the Perenio Smart Building Management System mobile application on your smartphone and login in to the User Account (See par. A below). 3. Scan the QR Code, or enter CG data manually (See par. B below).
Page 37 To restore a forgotten password, use the e-mail address linked to your User Account, to which instructions on changing the password will be sent. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 37 of 69...
Page 38 Perenio Smart App User Account;  For existing Users: After login to the Perenio Smart App User Account, click on the “+” icon in the upper right corner of the Devices tab, select “Add new device”...
Page 39 Control Gateway may not return to the Access Point mode, which means that the reset to factory settings will be required (See par. 2.2 below). ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 39 of 69...
Page 40 The Control Gateway will be displayed in the Devices tab. The entire process of the Control Gateway activation in the Mobile App is shown below. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 40 of 69...
Page 41: Figure 20 - Add New Device Procedure (The Cg Activation Process)
Installation and Operation Manual for Perenio® PEKIT01 Smart Security Kit – Add new device procedure (The CG activation process) Figure 20 ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 41 of 69...
Page 42: Reset To Factory Settings
(Connection via an Ethernet cable is temporary unavailable). 2.4 Wi-Fi Router Frequency Settings Perenio® PEACG01 Control Gateway may be connected to the Wi-Fi Network of 2.4GHz only. Due to this fact, the User shall make sure that your Wi-Fi Router is set to the above frequency before proceeding to par.
Page 43: Changing The Room Or Location For The Control Gateway
Change the Room/Location in Control Gateway settings ( 2. Change the room/location (The Wi-Fi Network will also be changed): a. Log in to the Perenio Smart app and select the Location where the Control Gateway is activated; b. In the Devices tab, select the required Control Gateway from the list and click on the icon (Settings);...
Page 44: First Installation And Configuration Of The Smoke Sensor
Smart Mobile App, it is necessary to perform the following steps: 1. Unpack the Sensor and switch it on (See par. E below). 2. Login in to the Perenio Smart Building Management System User Account (See par. B below). 3. Connect the Smoke Sensor to the Mobile App (See par. I below).
Page 45: Figure 21 - Installation Of The Smoke Sensor On A Flat And Sloping Ceiling
Smoke Sensor. 5. Switch on the Smoke Sensor by removing the battery isolation strip. 6. Reassemble the Smoke Sensor and the mounted bracket. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 45 of 69...
Page 46: First Installation And Configuration Of The Leak Sensor
Smart Mobile App, it is necessary to perform the following steps: 1. Unpack the Sensor and switch it on (See par. E below). 2. Login in to the Perenio Smart Building Management System User Account (See par. B below). 3. Connect the Smoke Sensor to the Mobile App (See par. I below).
Page 47: Leak Sensor Tightness
Perenio® PEKIT01 Smart Security Kit SWITCHING ON AND INSTALLATION OF THE LEAK SENSOR To install the Perenio® PECLS01 Leak Sensor, follow steps below: 1. Unpack the device. 2. Select suitable installation area near a potential source of flood (water valve, washing machine, radiators, etc.).
Page 48: First Installation And Configuration Of The Pecws01 Sensor
Perenio Smart Mobile App, it is necessary to perform the following steps: 1. Unpack the Sensor and switch it on (See par. E below). 2. Login in to the Perenio Smart Building Management System User Account (See par. B below).
Page 49: Figure 25 - Installation Rules For The Sensor And The Magnet
NOTE. The Sensor and the magnet shall be mounted coaxially so that in the closed position of the door or the window the magnet is at a distance of no more than 2 cm from the sensor. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 49 of 69...
Page 50: First Installation And Configuration Of The Motion Sensor
Smart Mobile App, it is necessary to perform the following steps: 1. Unpack the Sensor and switch it on (See par. E below). 2. Login in to the Perenio Smart Building Management System User Account (See par. B below). 3. Connect the Smoke Sensor to the Mobile App (See par. I below).
Page 51: Figure 26 - Motion Sensor Orientation During Installation
(near heaters, refrigerators, stoves, etc.). After the above Steps 1-6 are successfully completed, the Motion Sensor is considered to be installed and ready for operation. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 51 of 69...
Page 52 Control Gateways activated in the User Account). NOTE. The Control Gateway must be connected to the mains and the Internet, as well as activated in the Perenio Smart App. Start searching for Sensors; d. If the LED flashes slowly after the first power on of...
Page 53: Figure 27 - Add New Device (Sensor) Procedure
PEKIT01 Smart Security Kit The entire process of the Sensor connection in the Mobile App is shown below. – Add new device (Sensor) procedure Figure 27 ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 53 of 69...
Page 54: Changing The Room Or Location For Sensors
Change the Room in Sensor settings in the User Account. 2. Change the room/location (Connection to another CG is required) as follows: a. Sign in to the Perenio Smart app and select the Location where the Sensor is activated;...
Page 55: History And Push-Notifications
Gateway firmware update process, as well as low battery notifications and changes of the Armed/Disarmed mode for the Location. Standard events. Various news and other information from Perenio IoT, as well as alerts from both the Door&Window Sensor and the Motion Sensor when in the Disarmed mode.
Page 56: Upgrading The Control Gateway Firmware
Perenio® PEKIT01 Smart Security Kit 2.12 Upgrading the Control Gateway Firmware Perenio IoT strives to constantly improve the quality of its products, so an automatic software (firmware) update can be launched during the first activation of the Control Gateway, as well as during its normal operation.
Page 57: Battery Replacement
Motion Sensor Sensor Window Sensor Sensor Positioning of the battery in Sensors Figure 28 – After battery replacement, the LED of the Sensor will blink. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 57 of 69...
Page 58: Maintenance And Repair
 Repair mechanical damages to devices (in Service Centers). Perenio® PEKIT01 Smart Security Kit repairs shall be carried out in Service Centers, because casings will have to be opened in the case of any element failure. In the case of warranty repairs or replacement, the User shall provide the Seller with the sales receipt and the purchased device.
Page 59: Warranty Obligations
The Manufacturer shall guarantee that all materials, components and assemblies of Perenio® devices are free from defects under normal operation within the warranty period. The limited warranty shall be applied to the first End Customer of Perenio® devices only and cannot be transferred to a subsequent customer.
Page 60 Seller, as well as the date when this device was sold. LIMITATION OF LIABILITY Perenio® devices SHALL NOT BE SUBJECT TO a free warranty service in the case of identification of at least one of the following damages or defects: ...
Page 62: Storage, Transportation And Disposal Of Devices
PEKIT01 Smart Security Kit 5 Storage, Transportation and Disposal of Devices Perenio® Smart Security Kit may be shipped by any kind of covered vehicles (by rail, or road or in sealed heated airplane compartments, etc.) in accordance with the requirements of current regulatory documents applicable to fragile goods sensitive to moisture.
Page 63: Other Information
Quality Claims Acceptance and Warranty Service Company Croatia Name ASBISc-CR d.o.o. Address Slavonska avenija 24/6, 10000 Zagreb, RH Czech Republic Name ASBIS CZ, s.r.o. Address Obchodní 103, Čestlice, 25101 Poland ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 63 of 69...
Page 64 2018; Radio Test Report #STS183222W01 as of March 31, 2018; Radio Test Report #STS183222W02 as of March 31, 2018. Addresses of Service Centers are available at perenio.com in the ‘Support’ Section. Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 64 of 69...
Page 65: Troubleshooting
Short beeps after the Low battery level of Change the battery sensor is powered the sensor on, as well as absent or faint alarm ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 65 of 69...
Page 66 Damage of the Sensor Call the service center or the Magnet The sensor does not Low battery level Change the battery activate Doc Version: 2.4.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 66 of 69...
Page 68: Glossary
The color analog television system adopted in the USA, Japan, South Korea and some other Asian countries Perenio Smart Software developed by Perenio IoT for remote control of wireless Cameras from smartphones PIR Sensor The passive infrared sensor with a pyroelectric sensing...
Page 69 The area that falls into the field of viewing of the Sensor ZigBee A network protocol designed for secure transmission of data at low speeds, which is recognized for an extremely low power consumption ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.4.1 Page 69 of 69...

Perenio PEKIT01 Installation And Operation Manual

Quick Links

Related Manuals for Perenio PEKIT01

Summary of Contents for Perenio PEKIT01

Table of Contents