Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Consilium SAL R1E
- Page 1 SAL R1E Installation of bottom parts and transducers Article No. 5413105 çConsilium...
- Page 2 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Revisions Date Ver. Name Comment 2014-01-07 OM/SGu Created 2 (16)
- Page 3 SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 General The siting of the SAL R1E transducers is an important factor in determining the accuracy and efficiency of the overall system. The transducers are designed to be fitted flush with the hull. One of the tranducers measures the sea depth (ES = Echo Sounder) and the other transducer measures speed through the water (SL = Speed Log) in the water mass approximately 130 mm below the ship’s hull.
- Page 4 For more detailed installation advices please refer to the complete manual. 2. The SAL R1E mounting set should be installed in the foremost part of the vessel as close as possible to the keel line.
- Page 5 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Boundary Layer A moving ship’s hull tends to drag a layer of water with it, causing a boundary region around the hull. The water speed at the hull is almost the same as the ship’s speed, so that the relative water speed is almost zero.
- Page 6 SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Mounting Set Single Bottom Sea Valve (MSSBSV) The SAL R1E mounting set is suitable for installation on single bottom ships allowing the transducers to be removed without bringing the ship out of the water (dry-docking).
- Page 7 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Welding the Bottom flange in Ship’s hull Ship's Hull Notes: Welding work should be carried out by qualified personnel as required by the applicable classification society. The Red markings on the bottom flange shall point in ship’s forward direction.
- Page 8 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Mounting of the zinc ring and guide ring. Guide ring Red marking The Red marking on the guide ring shall be mounted pointing in the ship’s forward direction in line with the Red marking on the bottom flange! Fit the zinc ring and the guide ring into the base of the bottom flange and secure with the six MFS M10x30 screws, see figure below.
- Page 9 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Screw the eight M16x40 studs into the top of the bottom flange. Short threaded end downwards Stud Ships Hull Place Seal 1 on the cleaned flange surface. Seal 1...
- Page 10 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Mounting Sea Valve on Bottom flange It is NOT critical in which direction the valve handle/wheel is mounted relative to ship’s keel line. It can be mounted in any of the eight possible positions to provide convenient operation.
- Page 11 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Mounting of the transducers The SAL R1E Top Assembly is pre-mounted from the factory and ready for mounting of the two transducers. Side view Height after installation approx. 62 mm...
- Page 12 2. Assure that the Seal 2 is placed on top of the Sea Valve flange. 3. The SAL R1E Top Assembly shall be mounted on the Sea Valve with the Red marking on the valve cover top pointing in the ship’s forward direction in line with Red markings on the bottom flange and guide ring.
- Page 13 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Red marking indicates forward direction. Red marking on top of valve cover plate must be in line with Red markings on the bottom flange and guide ring. Ship’s forward...
- Page 14 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 Orientation of Transducer Connecting Tubes Turn and fine adjust each connecting tube so that the flat section on the connecting tubes faces to starboard, SB, and is parallel within ±3° to the keel line.
- Page 15 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 SAL R1E MSSBSV / Part Numbers / Assembly Diagram Part no. Sea valve, DN125, PN16 71-22187-00 Zinc ring 71-22182-00 Nut ML6M M16, A4 71-22022-00 Stud screw M16x40 (total L = 60)
- Page 16 çConsilium SAL R1E Installation of bottom parts and transducers Art No. 5413105A01 SAL R1E MSSBSV / Main dimensions 16 (16)
Need help?
Do you have a question about the SAL R1E and is the answer not in the manual?
Questions and answers