Advertisement
Quick Links
IR100
IR101
!
WARNING
Protective
Handle (2)
Caster
(4)
Front
Leg (2)
Additional tools required:
Phillips or Robertson Head Screwdriver
Wrenches (2 of Each): 7/16", 9/16" & 1/2"
OR Two Adjustable Wrenches
Rubber Mallet
PLEASE KEEP THIS GUIDE WITH THE PRODUCT
WATCH OUR ASSEMBLY VIDEO AT WWW.I-ROVER.INFO
3
Year
Frame
Warranty
Please Recycle
Royal® iRover Standard/Premium -
IR100/IR101_2010_A
This Assembly Guide provides instructions
to build the Premium or Standard models of
the iRover.
Check out our other products online at
www.copernicused.com
This Product is meant to be assembled by an adult.
In its unassembled state, small parts present a hazard.
To be used under direct supervision of an adult.
Bottom Rollbar Round Tube (1)
SMARTBoard
660 OR 680 (1)
(Sold Separately)
Upper Frame (1)
Laptop
Arm
Pre-Assembly (1)
Validate Your Warranty & Enter to Win!
To validate your three year frame warranty, submit the ON-LINE form at www.copernicused.com
Enter a draw to win a Copernicus Product for your classroom at the same time!
IR100 IR101 - Version A - 23 February 2010 - Copernicus Educational Products Inc.
For assistance, please contact us:
1-800-267-8494
Email info@copernicused.com
Have your packing slip ready for reference
Installation instructions for either
the Lock Box or Shelf included
Projector Arm
Pre-Assembly (1)
Board Mounting
Bracket (1)
OR
Back
Remaining parts
are hidden
Assembly Guide
Projector
Projector Arm
Slide (1)
Faceplate (1)
Frame Upper
Slide Pole (1)
Frame Upper
Slide (1)
Back Support
(2)
Lock Box (1)
Wire Management
Channel (1)
Shock Bracket
(1)
Gas Cylinder
(1)
Slide Guide
(1)
Advertisement
Summary of Contents for Touchboards Royal iRover Standard
- Page 1 IR100 Royal® iRover Standard/Premium - Assembly Guide IR101 IR100/IR101_2010_A For assistance, please contact us: This Assembly Guide provides instructions to build the Premium or Standard models of 1-800-267-8494 the iRover. Email info@copernicused.com Check out our other products online at Have your packing slip ready for reference www.copernicused.com This Product is meant to be assembled by an adult.
-
Page 2: Before You Begin
Tips for Assembly Watch for These Helpful Symbols This symbol denotes a 2 or 3 Person Task. For safety, please ensure that there are the suggested number of people working on steps displaying this symbol 2 Person Task 3 Person Task Watch for this symbol throughout the Assembly Instructions. - Page 3 Royal® iRover Premium - Parts Before beginning, you should have: Contents - Box IR100-0 Hardware Contents - Box IR00-0-A Actual Size In Box Back Support Back Support 43204 430083 IR100-0-A with Laptop 33044 Connector 510731 33044 430081 330501 (connector) 430141 Upper Frame &...
- Page 4 Royal® iRover Premium - Parts Before beginning, you should have: Contents - Box IR100-PA Hardware Actual Size 43205 Projector Slide Projector Arm Pre-Assembly Projector Mount 430061 430102 330494 Plate Assembly Gas Cylinder 330493 330491 34010, 34009, Pre Assembled 330492 34008 25511 430237 Top Rollbar...
- Page 5 Do not tighten any fasteners, unless instructed Actual Size: You will need: (Not to Scale) Caster x 4 Leg x 2 Install Casters Lock Casters to tighten, & leave locked for remainder of Assembly To tighten casters use a large adjustable wrench IR100 IR101 - Version A - 23 February 2010 - Copernicus Educational Products Inc.
- Page 6 Actual Size: You will need: (Not to Scale) 3 Person Task Slide Guide x 1 Frame Upper Slide x 1 Build Sliding Frame Note orientation - square standoff directed Please note: Sliding parts are lubricated with a Petroleum towards front Based Jelly to ensure smooth movement when adjusting the height.
- Page 7 Actual Size: Included with original hardware silver colored You will need: (Not to Scale) 3 Person Task Frame Upper Slide Pole x 1 CONTINUED...Build Sliding Frame Note orientation of tabs with respect to the front of the unit FRONT Must be very tight Bang in with...
- Page 8 Actual Size: You will need: (Not to Scale) 2 Person Task Upper Frame PreAssembly x 1 Install Upper Frame & Secure Release Lever End of Release cable snaps Note onto the bottom of the cylinder orientation: Channel should face to the back WARNING! Shock is under pressure! Do not pull trigger once cable is connected.
- Page 9 Actual Size: You will need: (Not to Scale) Back Support x 1 Back Support with Laptop Connector x 1 Install Back Supports Looking from the FRONT, ensure Laptop Connector is on the right hand side IR100 IR101 - Version A - 23 February 2010 - Copernicus Educational Products Inc.
- Page 10 Actual Size: You will need: (Not to Scale) Upper Stretcher (6 thru holes) Install Upper Stretchers Before securing Upper Stretchers, ensure Gas Cylinder is upright You may want to secure the shock upright with an enclosed Velcro Strap until it is fastened Actual Size: You will need: (Not to Scale)
- Page 11 Actual Size: 43044 Not to Scale You will need: (Not to Scale) 2 Person Task Lock Box x 1 Marker Bin x 1 If you are installing a LOCK BOX Install Lock Box Magnetic Marker Bin can be used on any magnetic surface. Try on the inside OR outside of Lock Box.
- Page 12 Actual Size: x 12 T - Nylon You will need: (Not to Scale) Spacer Lower Stretcher x 2 Shelf x 1 Shelf Stretcher x 2 If you are installing the Shelf Install Lower Stretchers & Shelf Do not tighten hardware until all parts are attached Hardware Item T - Nylon Spacer goes between the Shelf &...
- Page 13 Actual Size: silver colored You will need: (Not to Scale) 3 Person Task Projector Arm Pre- Upper Mount Bracket x 1 Assemblyt x 1 Install Projector Arm & Upper Mount Bracket Slide Projector Arm Pre-Assembly into Base Frame Note orientation of until holes align Projector Arm compared to the Frame...
- Page 14 For use with Sharp PG-F267X ONLY Actual Size: Q - Spacer Actual Size: White You will need one of the following projectors: You will need: (Not to Scale) Sharp PG-F267X Epson Powerlite 410W Projector Projector NEC600S Projector Upper Mount Bracket x 1 Install Projector to Projector Mount Plate Projector illustrated may look different from the one you are installing...
- Page 15 Actual Size: You will need: (Not to Scale) Bottom Rollbar Projector Arm Faceplate x 1 Round Tube x 1 Install Faceplate & Bottom Rollbar IR100 IR101 - Version A - 23 February 2010 - Copernicus Educational Products Inc.
- Page 16 Actual Size: Install Projector Slide Assembly onto iRover Frame Slide Projector Slide Arm Assembly all the way into the Projector Arm Assembly Insert male end of VGA Cable (VGA extension included with iRover) & female end of Projector Power Cords through Arm, starting from the back Feed enough cord through to leave about 2’...
- Page 17 Actual Size: You will need: (Not to Scale) SMARTBoard Wall Mount Board Bracket x 1 - This is found in the box with your SMARTBoard Install SMART Board Wall Mount Board Bracket STOP Ensure all fasteners up to this point are tightened IR100 IR101 - Version A - 23 February 2010 - Copernicus Educational Products Inc.
- Page 18 Actual Size: You will need: (Not to Scale) 2 Person Task SMARTBoard 660/680 x 1 Install SMARTBoard Mounting Bracket slips underneath the top of the SMARTBoard frame Tab flexes - you must apply pressure to press it in as you install the Board Lower Mounting Holes SMART 660...
- Page 19 Actual Size: You will need: (Not to Scale) 2 Person Task Protective Handle x 2 Install Protective Handles Handles adjust depending on the size of your board. SMARTBoard 660 If installing a larger board or one with side speakers, adjust the Handles outwards to fit comfortably around your Board Note Handle positioning in comparison...
- Page 20 You will need: (Not to Scale) Laptop Arm Pre-Assembly x 1 Install Laptop Arm Pre-Assembly onto Laptop Tray Connector Slide Laptop Arm Pre-Assembly onto Laptop Arm Connector IR100 IR101 - Version A - 23 February 2010 - Copernicus Educational Products Inc.
- Page 21 You will need: (Not to Scale) Quick Tips Label x 1 Power Bar x 1 Attach Power Bar & Adhere Quick Tips Label Peel and Stick the Quick Tips Label to the back of the SMARTBoard Stick Power Bar onto double sided tape in Wire Management Channel IR100 IR101 - Version A - 23 February 2010 - Copernicus Educational Products Inc.
- Page 22 You will need: (Not to Scale) Black One-Wrap Cable Velcro Strap Split Black 9x (Projector Arm) Wire Loom 25517 3x (Laptop Arm) 43321 2 Person Task 25505 Not to Scale Routing Cables Through the iRover VGA Cable (1 VGA Cable provided with iRover ) VGA Cable &...
- Page 23 Adjusting Projector for Use/Correcting the Projected Image Turn Hardware Item ‘W1’ to tilt the projector upwards or downwards Turn Hardware Item ‘W2’ to tilt the projector to either the left or right Loosen Hardware Items ‘X’ in both locations to allow for sideways adjustment of the projected image Re-tighten to lock in place once desired image is achieved...
- Page 24 Adjusting Projector for Use/Correcting the Projected Image Tighten two nuts down when image is correct MUST BE TIGHT 1. To center the Projector Arm, rotate the Center Pole position by adjusting the bolt. 2. Turn bolt counter-clockwise or clockwise to center the arm.
- Page 25 Survey Fill Out a User Survey for a FREE Product! After using your NEW iRover for a minimum of 1 month, please answer this brief survey. As our thanks for submitting a Survey, we will send you a FREE GIFT of your choosing! Please mail completed surveys to: Copernicus Educational Products, Research &...