Advertisement
3.
OpERATION
IMpORTANT WARRANTY INFORMATION:
The battery pack fitted to this cordless tool is considered to be a
consumable item and its ability to accept charge will educe over
time. We will warranty it against mechanical and electrical defect for
a period of one year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or regularly
conditioned, its capacity will diminish. under these circumstances
we will not replace the battery pack even if it is less than one year
old.
3.1. To charge the screwdriver, insert the charger jack into the charging
socket on the screwdriver (fig.1) and plug the charger into a mains
socket. The red LED on top of the screwdriver will illuminate to
indicate the battery is being charged. When charging is complete
(a full charge is 3 to 5 hours), unplug the charger from the mains
and the screwdriver.
3.2. Place the appropriate bit into the bit holder of the screwdriver.
Select the required direction by using the reverse switch (which
will lock the screwdriver, in it's central position) and squeeze the
power trigger to start the screwdriver (fig.1).
3.3. To select the desired speed, slide the speed selector to either the
'1' or '2' position (fig.2).
3.4. To select torque or drill setting, twist the torque selector (fig.1)
around to the required setting - from 1 (the lowest) to 15
(the highest) for torque setting or to the drill symbol for drilling.
3.5. To check the condition of the battery, press and hold down the
battery indicator button next to the battery level indicator (fig.2).
If all LEDs illuminate, there is sufficient charge, if just the yellow
and red LEDs illuminate, the screwdriver will soon need charging, if
just the red LED illuminates, the screwdriver needs to be charged
immediately.
3.6. When finished using the screwdriver, remove the bit from the bit
holder, pulling back the quick release bit holder (fig.1) if needed.
Clean the screwdriver and replace all parts in the storage case.
Store the case in a safe, dry, childproof location.
Cordless Screwdriver 7.2V no. CP72S when operated in accordance with these instructions and tested in accordance with BS En
28662-1:1993, ISo 8662-1:1988 and BS En ISo 8662-7:1997 results in the following vibration emission declared in accordance with
BS En 12096:1996.
Measured vibration emission value: 0.72m/s²
These values are suitable for comparison with
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
This is a 'NO LOAD' vibration figure.
A competent person should carry out a risk assessment following HSE guidelines.
Measurement results can be highly variable, depending on many factors, including the operator's technique, the condition of the work
equipment, the material being processed and the measurement method.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
We recommend appropriate safety equipment is utilised and regular breaks for the operator are employed to reduce any residual risk
of fatigue or repetitive strain injury.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycle centre and disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
Contact your local solid waste authority for recycling information.
Remove the retaining screws and split the casing halves revealing the battery compartment.
Remove the battery by carefully cutting the wires.
Dispose of the battery according to local authority guidelines.
under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak's
Li-Ion
registered compliance scheme. Jack Sealey Ltd's Batteries Producer Registration number (BPRn) is
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMpORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Risk of Hand Arm Vibration Injury
Uncertainty: 0.29m/s²
emission levels of other tools that have been subject to the same test.
Environmental protection
Battery Removal
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
fig.1
01284 757500
Web
01284 703534
email
fig.2
BPRn00705.
www.sealey.co.uk
sales@sealey.co.uk
CP72S
Issue: 4 - 13/01/12
Advertisement
