Olympus JetHeat OLY-J3/1 Datasheet

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Olympus Industrial Appliances JETHEAT FAN HEATER product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
Refer to
Indoor Use
Instructions
Only
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the purchaser and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) or suitable should be incorporated in the main distribution
board. It is recommended that a Residual Current Device (RCD) is used. It is important to use an RCD with portable products that are
plugged into a supply that is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your JetHeat supplier for advice.
You must also read and understand the following instructions concerning suitable electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it
to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends
beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13amps are supplied without a plug. In this case you must contact a qualified electrician
to ensure that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin
plug and socket with your electrician.
1.1.11. If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and should be at suitable for this
product and for others which may be used on the other output sockets, we recommend the use of 2.5mm² section cable.
1.2. GENERAL SAFETY
WARNING! Disconnect the heater from the mains power supply, before servicing or performing any maintenance. Servicing or

maintenance must only be carried out by an authorised service agent.
Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.

Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.

Position the heater at least a minimum of 0.5mtr at the rear and sides, and 2mtr at the front, from any walls or objects.

WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders etc.

DO NOT obstruct the air inlet and outlet sections of the heater.

DO NOT cover the heater.

DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.

DO NOT touch the heater casing or grill when first switched off, as these will be very hot and will take time to cool.

DO NOT use the heater for anything other than its intended purpose. It is designed to provide heat in enclosed areas, such as

workshops and other industrial areas. It is not suitable for drying clothes or laundry.
DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.

DO NOT get the heater wet or use in areas of high condensation.

© Olympus Industrial Appliance UK
MANUAL FOR
INDUSTRIAL FAN HEATER
Output: 3KW 2 HEAT SETTINGS
Model No: Olympus JetHeat OLY-J3/1
Original Language UK English
THIS PRODUCT REQUIRES A UK 3 PIN 13A PLUG.
IT IS RECOMMEND THAT YOU
DISCUSS THE INSTALLATION
OF THE PRODUCT IF YOU ARE
UNSURE IN ANY WAY WITH A
QUALIFIED ELECTRICIAN.
, are fitted with live (brown) and neutral (blue) wires only.
Olympus OLY-J3/1| Issue 1) 16/08/16
RECOMMENDED
FUSE RATING - 13A