Advertisement
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Lehle P-SPLIT III
Summary of Contents for Lehle P-SPLIT III
- Page 1 OPERATING INSTRUCTIONS P-SPLIT III...
- Page 2 Every assembly of your LEHLE P-SPLIT III has been made and tested in Germany. Your LEHLE P-SPLIT III is of extremely ro- bust design and construction, to make sure that you get absolutely years and years of enjoyment from it. If you should...
-
Page 3: Table Of Contents
Technical data Unbalanced signal routing Balanced signal routing Preconditions for passive splitting General description Typical uses of the LEHLE P-SPLIT III as splitter for two amps compact passive DI box line isolator – the universal cure for hum loops recording splitter... -
Page 4: Introduction
Its applications range from splitting sig- anced signal on the ISO output, the LEH- nals and eliminating hum, to balancing LE P-SPLIT III is also eminently suitable for and re-amping along with any signal use as a high-quality compact DI box for routing that requires a clean signal free all types of signal. -
Page 5: Technical Data
0.003 % (0 dBu, 1 kHz) Frequency range 20 Hz – 100 kHz -0.1/ +0.4 dB (source 600 Ω, load 1 MΩ) min. 2 MΩ at 2 kHz Input impedance (transformer load impedance) LEHLE GmbH · Germany · www.lehle.com · support@lehle.com... -
Page 6: Unbalanced Signal Routing
Ground Signal in phase signal conductor and constitutes the sig- nal ground. UNBALANCED SIGNAL ROUTING JACK JACK Cable Sleeve Ground Sleeve Signal in phase LEHLE GmbH · Germany · www.lehle.com · support@lehle.com... -
Page 7: Balanced Signal Routing
The third conductor is the screening, and again constitutes the signal ground (Sleeve, XLR Pin 1). BALANCED SIGNAL ROUTING JACK Cable Sleeve Ground Pin 1 Ring Signal in mirrored phase Pin 3 Signal in phase Pin 2 LEHLE GmbH · Germany · www.lehle.com · support@lehle.com... -
Page 8: Preconditions For Passive Splitting
PRECONDITIONS FOR PASSIVE SPLITTING: The LEHLE P-SPLIT III is a passive splitter ly susceptible to interference. Long cable which can be used to split high-imped- routings audibly attenuate high frequen- ance signals to high-impedance inputs. cies. Electromagnetic interference from There are certain preconditions which... - Page 9 10m. Your individual taste will ultimately de- WHAT IS POSSIBLE cide, however. The LEHLE P-SPLIT III can be used to split Splitting your high-impedance instrument the signal from an electric guitar or elec- signal to a low-impedance input, such as...
-
Page 10: General Description
LEHLE P-SPLIT III input here. semiconductors or any other active com- ponents in the signal path. The input signal and its ground are pre- sent directly on the DIR socket. The signal LEHLE GmbH · Germany · www.lehle.com · support@lehle.com... - Page 11 Inverting the phase eliminates this prob- lem. The P-SPLIT III can be mounted to a plate such as a pedalboard using the two holes Experiment to find out which position you in the bottom of the pedal.
- Page 12 LEHLE GmbH · Germany · www.lehle.com · support@lehle.com...
- Page 13 TYPICAL USES LEHLE P-SPLIT III AS A SPLITTER FOR TWO AMPS DEVICE CONNECTION Input Instrument Output Amplifier 1 I S O D I R Output Amplifier 2 P- S P L I T M A D E I N G E R M A N Y...
- Page 14 LEHLE P-SPLIT III AS A COMPACT PASSIVE DI BOX DEVICE CONNECTION Input Instrument (active) Output Amplifier I S O D I R Output Input mixer, stage box P- S P L I T M A D E I N G E R M A N Y The LEHLE P-SPLIT III can be used as a 5.
- Page 15 LEHLE P-SPLIT III AS A LINE ISOLATOR – THE UNIVERSAL CURE FOR HUM LOOPS DEVICE CONNECTION Input Signal source Output Signal input I S O D I R P- S P L I T M A D E I N G E R M A N Y...
- Page 16 LEHLE P-SPLIT III AS A RECORDING SPLITTER DEVICE CONNECTION Input Instrument (active) Output Amplifier I S O D I R Output Sound card (Hi-Z) P- S P L I T M A D E I N G E R M A N Y...
- Page 17 You can, of course, also use a balanced tween the instrument and the input of input on your sound card or DAW to the LEHLE P-SPLIT III to convert the high- record the dry signal. In this case, it’s a impedance instrument signal to a low-...
- Page 18 5. There you go! This problem can be effectively eliminat- ed using the LEHLE P-SPLIT III. The built- in LEHLE TRANSFORMER HZ galvanical- ly isolates the ground connections, and functions perfectly with both balanced and unbalanced signals from a sound In this case, the LEHLE P-SPLIT III is card or a DAW.
- Page 19 LEHLE P-SPLIT III AS A BALANCED/UNBALANCED SIGNAL CONVERTER DEVICE CONNECTION Input Signal source (un)balanced I S O D I R Output Signal input (un)balanced P- S P L I T M A D E I N G E R M A N Y...
- Page 20 Up to 100m of cable can be connected cable runs from a pedalboard to an amp to the TRS output socket. The LEHLE P- which, on large stages, can be some dis- SPLIT III can be used at the end of the line tance away.
- Page 21 LEHLE P-SPLIT III AS A PASSIVE SUMMING BOX FOR STEREO SIGNALS DEVICE CONNECTION Input Left signal Output Right signal I S O D I R Output Amplifier / Monitor speaker P- S P L I T M A D E I N G E R M A N Y...
-
Page 22: Lehle P-Split Iii Signal Flow Diagram
LEHLE P-SPLIT III SIGNAL FLOW DIAGRAM PHASE ( ) INPUT ( ) ISO ( ) GROUND ( ) DIR ( ) LEHLE GmbH · Germany · www.lehle.com · support@lehle.com... - Page 23 LEHLE GmbH · Grenzstrasse 153 · 46562 Voerde · Germany www.lehle.com · support@lehle.com LEHLE P-SPLIT III OPERATING INSTRUCTIONS EN V1.0 · 2019-08-01 Copyright 2019 by LEHLE LEHLE GmbH · Germany · www.lehle.com · support@lehle.com...
Need help?
Do you have a question about the P-SPLIT III and is the answer not in the manual?
Questions and answers