Related Manuals for Swann ULAD-1913
Summary of Contents for Swann ULAD-1913
- Page 1 ULAD-1913 ADA Lavatory Bowl Product Warnings Safety Guidelines General Information Installation Procedure Cleaning & Maintenance Warranty Information Form # 375 12-11...
-
Page 3: Safety Guidelines
Safety Guidelines CAUTION IMPORTANT NOTICE CAUTION: Indicates a potentially hazardous IMPORTANT NOTICE: Indicates that equipment or situation which, if not avoided, may result in injury. It property damage can result if instructions are not may also be used to alert against unsafe practices. followed. - Page 4 Safety Guidelines Dust Hazard WARNING When cutting or drilling the product, use a dust collection method which WARNING: Indicates potentially hazardous prevents dust particles from going into situation which, if not avoided, could result in serious the air. Always work in a well-ventilated area. Always injury or death.
-
Page 5: General Information
General Information General Tools Disclaimer The photos shown in the instructions may be 2-1/2 hp router (such as Porter Cable 7539). different from the actual sink being installed; Drill or cordless drill (such as DeWalt DCD940KX 18V however, the installation method is the same. Variable Speed Reversible Driver Drill). - Page 6 Installation Vanity Sink Installation 5. Thoroughly sand the underside of the countertop, inside the sink outline, with 36 grit sanding pads. This procedure provides instructions for under mounting Sand an area 3 inches wide up to the pencil line. a vanity sink directly to a solid surface countertop using Remove all gloss and rough up the surface to allow color-matched acrylic adhesive.
-
Page 7: Installation
Installation c. Remove the sink and use compressed air and IMPORTANT NOTICE denatured alcohol with a clean cloth to remove all dust and debris from the holes, sink rim, and vanity surface. Before glue-up, wipe all the sanded surfaces with a clean cloth and denatured alcohol. - Page 8 Installation 14. Once the sink is securely clamped in place, carefully IMPORTANT NOTICE remove one of the two screws from the rim of the sink, then retighten that screw. Repeat for the To avoid damaging the sink or vanity top, do not second rim screw.
- Page 9 Installation Sink Cut-Out 16. Once the adhesive has cured, remove the clamps. Use the Swanstone Part # VW 0050-000 special With the sink secured to the underside of the countertop, countersink drill bit and drill pilot holes in the the opening for the under mount sink can be cut and remaining sink rim screw locations.
- Page 10 Installation Note: Marks on the sink caused by the router bit IMPORTANT NOTICE bearing will be removed during the sanding process in a later section. Before cutting the opening in the countertop, make sure the depth of the router bit is adjusted to allow the bearing to ride against the surface of the sink, just below the seam.
- Page 11 Installation Note: Marks on the sink caused by the router bit IMPORTANT NOTICE bearing will be removed during the sanding process in a later section. Before beveling the opening in the countertop, make sure the depth of the router bit is adjusted to allow the bearing to ride against the sink, just below the seam.
- Page 12 Finishing Note: Marks on the sink caused by the router bit IMPORTANT NOTICE bearing will be removed during the sanding process in a later section. Before rounding the opening in the countertop, make sure the depth of the router bit is adjusted to allow the bearing to ride against the sink, just below the seam.
- Page 13 Finishing Note: Inspect all joints and seams, looking for gaps or Use 120 grit sanding pads to remove router bit bearing marks, and to blend edges and seams. cracks. If voids in the adhesive joints are found, the components should be taken apart and reglued. 2.
-
Page 14: Maintenance
Maintenance Product Care and Cleaning For the most stubborn sink stains, fill the swanstone sink about one quarter full with a 50/50 solution of bleach Swanstone solid surface products are stain and abrasion and water. After 10 or 15 minutes of soaking, drain the resistant;... - Page 15 LIMITED WARRANTY FOR COMMERCIAL APPLICATIONS If a Swan Corporation product covered by this warranty is found to be defective in materials or workmanship, after inspection by an authorized Swan Corporation representative, we will repair, or at our option, exchange the product for a similar model. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation.
- Page 16 Save these Installation Instructions for future reference. They provide important information on cleaning and maintenance of Swan Corporation products. www.theswancorp.com Form # 375 12-11...