Accessories Installation Sequence Of Operation Functions Of The Control Valve Control Valve Operation Sketch Control Valve Schematics 9-10 Control Valve Repair Parts List SPX Power Team Pump SPX Power Team Pump Operation Preventive Maintenance Preventive Maintenance Forney Authorized Service Representatives 16-20...
Page 3
(24) months from the date of shipment from Hermitage, Pennsylvania. Terms and Conditions of Warranty A. If within 24 months from the date of shipment from the Forney factory, the LA-270 Series tester malfunctions, is noted defective or not complying with the stated A.S.T.M.
LA-270 Series Instruction Manual Installation Procedure 1. Before uncrating, inspect to see that no visual damage has occurred during shipment. If damage has occurred, notify the delivering carrier immediately. 2. Locate the packing list and carefully uncrate and remove. Check parts and units against the packing list to make sure the shipment is complete.
LA-270 Series Instruction Manual ACCESSORIES (METHOD OF INSTALLATION) All stock item accessories for the LA-270 Series Testing Machines are held in place by means of a holding stem (TA-0176) and a set-screw (TM-2090). Accessory Installation Place the accessory with the holding stem attached, up into the center hole of the receiver and tighten the set-screw.
LA-270 Series Instruction Manual Sequence of Operation Testers Equipped with Control Valve, HA-0619 1. Motor switched off, carefully center specimen in testing machine. 2. Turn Control Knob No. 2 clockwise to a snug position. 3. Position Valve Control Handle No. 1 to the “Metered Advance” position.
LA-270 Series Instruction Manual FUNCTIONS OF THE HA-0619 CONTROL VALVE (REFER TO FIG. 1) Metered Advanced Position This position of the Control Handle No. 1 allows the operator to adjust the rate of loading. Using Control Knob No. 2 as the adjustment, turn the control knob clockwise for a decrease and counterclockwise for an increase in the rate of load.
Page 8
LA-270 Series Instruction Manual Forney Technical Support Page 8 of 20 1/17/2007 800-367-6397...
Page 9
LA-270 Series Instruction Manual Forney Technical Support Page 9 of 20 1/17/2007 800-367-6397...
LA-270 Series Instruction Manual Control Valve Parts List ITEM PART DESCRIPTION Req`d, 250885 Knob 21639 Stud 11455 Snap Plug 11010 Machine Nut (#10-32 UNF) 44708 Valve Knob 302938 Flow Control Valve 10008 Socket Cap Screw (1/4-20 x ¾”LG.) 11916 Roll Pin 11229 O-ring (2 3/8”...
Page 11
HA-0619-58 Roll Pin 5/16x1 HA-0619-59 O-Ring 2 3/8 x 2 3/16 x 3/32 We recommend that you contact a FORNEY authorized service technician to service and install repair parts on your machine. Forney Technical Support Page 11 of 20 1/17/2007...
Page 12
LA-270 Series Instruction Manual LA-270 SERIES EQUIPPED WITH SPX POWER TEAM PUMP The oil reservoir has been filled prior to shipment with Dexron III Automatic Transmission Fluid. NEVER OPERATE THE ELECTRIC PUMP WITHOUT OIL!!! Keep the oil level to approximately 1” to 1 ½” from the top of the reservoir with the hydraulic piston in the testing machine retracted all the way.
LA-270 Series Instruction Manual Operating Instructions SPX Power Team Pump This two-stage hydraulic pump incorporates precision design and engineering features, which make it the most outstanding pump of its kind on the market. All moving parts are made from high-grade tool steel, heat-treated, machined, ground and lapped to extremely close tolerances to assure efficient operation and long life.
LA-270 Series Instruction Manual Preventive maintenance LA-270 Series Machines Keeping this unit clean and the oil free of dirt will increase the life of the pump & valve The reservoir should be drained, cleaned, and replenished with clean oil at least once a year or more often if possible.
LA-270 Series Instruction Manual Preventive Maintenance LA-270 Series Machines Checking & maintaining the oil level Check the oil level in the reservoir by removing the plastic cap on the top of the cover plate, the oil level should come to within 1” to 1 ½” of the cover plate with the piston retracted.
LA-270 Series Instruction Manual Forney Authorized Service Representatives Revised August, 2006 Company Name Account Territory A&A Enterprises 11455 California (Fresno & South) 12421 Charloma Dr. Guam Tustin, CA 92780-2400 Saipan Phone: (714) 730-7736 Kwajalein Fax: (714) 730-3685 Cell: (714) 357-6226 Attn: W.P.
Page 17
LA-270 Series Instruction Manual Milwaukie, OR 97222 Colorado Phone: (503) 654-9620 Idaho Fax: (503) 654-9670 Montana Cell: (503) 708-5357 Oregon Toll: (800) 356-4662 Utah Attn: Marshall Doyle Washington Ship to: 7010 SE Norbert Dr. Wyoming Milwaukie, OR 97222 Email: info@cal-cert.com...
Page 18
LA-270 Series Instruction Manual Email: calsercorp@sbcglobal.net Oklahoma Tennessee, Nashville West Wisconsin Coast Calibration Co., Inc. 15003 California 655 Linden Ave. Nevada in emergencies Carpinteria, CA 93013 Phone: (805) 684-1807 Fax: (805) 969-1846 Cell: (310) 748-9988 Attn: Ted R. Buergey Email: ted@coastcal.net...
Page 19
LA-270 Series Instruction Manual National Calibration, Inc. Texas 11900 Crown Point Drive # 140 San Antonio, TX 78233-5356 Phone: (210) 488-8161 Fax: (210) 590-7323 Attn: Mike Tedesco Pacific Calibration Service 35836 California (North and Central) 295 Old County Rd. Suite # 2...
Need help?
Do you have a question about the LA-270 Series and is the answer not in the manual?
Questions and answers