Page 1 Sidefeed Gearbox Baler, 3-Tie OPERATOR’S AND PARTS ADDENDUM S/N: STARTING WITH S/N 375E21G032 89-096 Important: Be certain to specify the A Product of serial number of your Baler when ordering parts. Sherwood, Oregon USA...
Page 2 Contents Safety ....................3-7 Serial Number Location ..............9 Maintenance ..................10 Gearbox Baler Parts ................ 11 Front End Installation, Gearbox 37X ..........12 . Front End Assembly, Gearbox 37X ........... 14-15 Engine Installation, Gearbox 37X ..........16-19 . Engine Assembly, Tier 4-Interim, Gearbox 37X ......20-23 .
Page 3 CAUTION Allied Systems Company cannot anticipate all worksite conditions, local regulations, etc. It is the responsibil- ity of the end user to be aware of and obey any specific The “CAUTION” symbol indicates a hazardous...
Page 4 Operation Warnings • Always use lights when working at night or in low light conditions. WARNING • Know your job-site rules. Some have site specific directions and procedures. The methods outlined in Failure to observe the following safety rules may this manual provide a basis for safe operation of the result in extreme personal injury, dismember- baler.
Page 5 • Any unauthorized modifications made to the baler check for hydraulic leaks. by the customer or parties other than Allied Systems • Small hydraulic hose leaks are extremely dangerous, will relieve Allied Systems Company and your Free- and can inject hydraulic man dealer of any liability for damage or injury.
Page 6 Electrical Hazards • Batteries produce explo- sive gases. Keep sparks, • An electric shock could flame and cigarettes be fatal. Ensure power to away. Ventilate when the baler is “OFF” before charging or servicing opening electrical panels. in an enclosed space. •...
Page 7 Fire Safety • Never perform welding operations until the entire machine has undergone a thorough cleaning. In WARNING addition, cover rubber hoses, disconnect the battery, and have at least a fire extinguisher at hand. • Hydraulic fluid is flammable. Do not weld on or near Diesel fuel and hydraulic oil are flammable.
Page 8 Intentionally Left Blank 89-096 Rev: 11-2016...
Page 9 Serial Number Location Serial Number Location Each Freeman Baler is identiﬁ ed by means of a baler model number and baler serial number. As a further identiﬁ ca- tion, all power units are provided with a serial number. The serial number is an important piece of information about the machine and it may be necessary to know it before obtaining the correct replacement part.
Page 10 Maintenance WARNING Chock baler wheels to prevent baler from mov- ing and make sure baler and tractor are both Fill/Check Plug turned off and all moving parts have come to a complete stop before starting any maintenance. Contact with moving equipment can cause seri- ous injury or death.
Page 11 Notes: This column identifies footnotes applicable to specified items. Part Number: This column lists the Allied Systems Company Part Number. Quantity: This column lists the total number of a specific item required per assembly or subassembly.
Page 12 Front End Installation, Gearbox Baler Front End Installation, Gearbox 37X Page 1 of 1 Page 1 of 1 Item Part No. Description Item Part No. Description 906814 Installation, Front End * 906815 . Front End Assembly 200454W . Capscrew R13806345 .
Page 13 Intentionally Left Blank Rev: 11-2016 89-096...
Page 14 Front End Assembly, Gearbox 37X Front End Assembly Page 1 of 2 Page 1 of 2 19 18 14 RH MOUNT 19 18 14 LH MOUNT 12 14 LEVER 19 18 14 BRACKET NOTES: - USE WASHERS (ITEM 5) AS NEEDED TO LIMIT SIDE-TO-SIDE MOVEMENT, BUT STILL ALLOW LEVER TO ROTATE FREELY. 89-096 Rev: 11-2016...
Page 15 Front End Assembly, Gearbox 37X Front End Assembly Page 2 of 2 Page 2 of 2 Item Part No. Description Item Part No. Description 906815 Front End Assembly F000007539 . Lever Weldment 221771W . Hard Washer F000007540 . Pin, Lift Lever Adj SQS3750750 2 .
Page 16 Engine Installation, 37X Engine Installation, 37X Page 1 of 4 Page 1 of 4 NOTES: 1-1 ENSURE 84 TO 86 PLUNGER STROKES PER MINUTE AT ENGINE FULL THROTTLE. 1-2 ENSURE 33 TO 35 PLUNGER STROKES PER MINUTE AT ENGINE LOW IDLE. 1-3 906189 ASSY SHOWN Item Part No.
Page 17 Engine Installation, 37X Engine Installation, 37X Page 2 of 4 Page 2 of 4 REFERENCE EXISTING BATTERY CABLE ON ENGINE ASSEMBLY REFERENCE #BAT0277000 12V BATTERY BATTERY STRAP & CABLE MOUNTING RED 12 GA WIRE REFERENCE FROM CONTROL BOX 370/375 BALER SHOWN EXISTING BATTERY HARNESS CABLE ON ENGINE...
Page 18 Engine Installation, 37X Engine Installation, 37X Page 3 of 4 Page 3 of 4 30 28 28 26 28 28 29 27 28 29 27 28 28 ENGINE BELLY PAN TO FRONT END ASSY. MOUNTING NOTES: MOUNT BATTERY GROUND CABLE TO THIS FASTENER ON THE ENGINE.
Page 19 Engine Installation, 37X Engine Installation, 37X Page 4 of 4 Page 4 of 4 REFER TO 906705 FOR ADDITIONAL AIR CLEANER ASSEMBLY NOTES AIR CLEANER MOUNT LOCATION ON SNORKEL USE EXISTING HARDWARE AIR CLEANER ASSEMBLY 34 33 18 19 34 33 MUFFLER AND TENSION CONTROL 370/375 BULLGEAR BALER SHOWN AIR CLEANER ASSEMBLY...
Page 20 Engine Assembly Engine Assembly Page 1 of 4 Page 1 of 4 WIDE TAB TEMP SENSOR NOTES: AFTER INSTALLING PULLEY CUT AWAY EXCESS SHAFT FROM CLUTCH. REMAINING SHAFT SHOULD EXTEND PAST PULLEY APPROXIMATELY 0.25". CONNECT WIRE END NARROW TAB TRIM SIDE CONNECTING TAB BEFORE TAPING. TO NARROW TAB.
Page 21 Engine Assembly Engine Assembly Page 2 of 4 Page 2 of 4 PRE-PAINT REMOVE FACTORY CAP & INSTALL PLASTIC PLUG. EXHAUST CLAMP COPPER NUTS (PROVIDED W/ENGINE) INSTALL CLUTCH BEARING (BEARING PROVIDED WITH CLUTCH). BRACKET ARRIVES INSTALLED BACKWARD. REMOVE & RE-INSTALL AS SHOWN.
Page 22 Engine Assembly Engine Assembly Page 3 of 4 Page 3 of 4 EXHAUST CLAMP BOLTS (PROVIDED W/ ENGINE) EXHAUST TUBE CLAMP (EXISTING ITEM) PRE-PAINT INSTALL ASC HOSE INSTALL TUBE AND FITTING. FOR EXHAUST. EXHAUST RESTRICTOR SEALS (PROVIDED WITH ENGINE) PRE-PAINT REMOVE DEUTZ PLUG FROM ENGINE.
Page 23 Engine Assembly Engine Assembly Page 4 of 4 Page 4 of 4 FUEL GAUGE CONTROLL BOX TEMP SENSOR 90° ELBOW LIGHTS ENGINE HARNESS PRE-PAINT TAPE ITEM 7 BATTERY OPENING SHUT. OLENOID ALTERNATOR CONNECTORS CLIP HARNESS INSTALL PRE-PAINT INSTALL SOFT PLUG (PROVIDE WITH ENGINE).
Page 24 Air Cleaner Assembly Air Cleaner Assembly Page 1 of 1 Item Part No. Description Item Part No. Description 254896 Air Cleaner Assembly 255496 . Body 255494 . Filter 255492 . Body Clamp 255495 . Filter, Safety 255493 . Cover ACL0002251 1 .
Page 25 Intentionally Left Blank Rev: 11-2016 89-096...
Page 26 Gearbox Installation (16" Frame) Page 1 of 5 SECTION A-A 1-11 16 27 28 29 SECTION B-B NOTES: SHIM GEARBOX TO ALIGN CRANK ARM PIN HOLE WITH DRIVE ARM PIN HOLE IN 4 QUADRANTS IN ITS RANGE OF MOTION. 16" CHAMBER & PLUNGER ASSY. SHOWN, REFER TO CHART FOR PLUNGER ASSEMBLIES FOR OTHER CHAMBER SIZES.
Page 27 Gearbox Installation (16" Frame) Page 2 of 5 Item Part No. Description Item Part No. Description 909233 Gearbox Installation (16" Frame) * 906765 . Gearbox Assembly 223587 . Nut, Esna * 904473 . Plunger Assembly 221560W . Capscrew 904466 . Drive Arm Assembly 221656W .
Page 28 Gearbox Installation (16" Frame) Page 3 of 5 15 34 1-10 PLUNGER STOP DOG 89-096 Rev: 11-2016...
Page 29 Gearbox Installation (16" Frame) DRIVE ARM DRIVE Page 4 of 5 GEARBOX PLUNGER DRAWBAR MOUNT (RIGHT HAND) DETAIL C ROLL PIN INSTL DRIVE ARM NOT SHOWN Rev: 11-2016 89-096 SECTION D-D...
Page 30 Gearbox Installation (16" Frame) Page 5 of 5 SHIMS WASHER DETAIL CAP INSTALLATION SAME FOR 904466 & 906841 WASHER DETAIL FASTENERS SERRATED EDGES HAND TIGHT BOTH SIDES DETAIL E WEDGE FEATURES " MAX WASHER DETAIL DETAIL F INSTALLATION NOTES: USE THE HARDWARE PROVIDED WITH THE ARM. INSTALL ITEM 36 SERRATED EDGES FACING OUT AND WEDGE FEATURES MESHED.
Page 31 Gearbox Installation 15”KTD (16” Frame) Page 1 of 5 17 18 SECTION A-A 13 16 27 28 29 30 SECTION B-B NOTES: SHIM GEARBOX TO ALIGN CRANK ARM PIN HOLE WITH DRIVE ARM PIN HOLE IN 4 QUADRANTS IN ITS RANGE OF MOTION.
Page 32 Gearbox Installation 15”KTD (16” Frame) Page 2 of 5 Item Part No. Description Item Part No. Description 909234 Gearbox Installation 15”KTD (16” Frame) * 906765 . Gearbox Assembly R13806363 . Capscrew * 906224 . Plunger Assembly 221660W . Capscrew 904466 .
Page 33 Gearbox Installation 15”KTD (16” Frame) Page 3 of 5 24 15 34 13 14 15 PLUNGER STOP DOG Rev: 11-2016 89-096...
Page 34 Gearbox Installation 15”KTD (16” Frame) Page 4 of 5 REF: GEARBOX REF: DRAWBAR MOUNT (RIGHT HAND) REF: PLUNGER ROD DETAIL C ROLL PIN INSTL DRIVE ARM NOT SHOWN 89-096 Rev: 11-2016...
Page 35 Gearbox Installation 15”KTD (16” Frame) Page 5 of 5 WASHER DETAIL SHIMS WASHER DETAIL CAP INSTALLATION SAME FOR 904466 & 906841 SERRATED EDGES BOTH SIDES FASTENERS HAND TIGHT GAP .010" MAX WEDGE FEATURES DETAIL E WASHER DETAIL DETAIL F INSTALLATION NOTES: USE THE HARDWARE PROVIDED WITH THE ARM.
Page 36 Gearbox Installation 14”KTD (16” Frame) Page 1 of 5 17 18 SECTION A-A 13 16 27 28 29 30 SECTION B-B NOTES: SHIM GEARBOX TO ALIGN CRANK ARM PIN HOLE WITH DRIVE ARM PIN HOLE IN 4 QUADRANTS IN ITS RANGE OF MOTION.
Page 37 Gearbox Installation 14”KTD (16” Frame) Page 2 of 5 Item Part No. Description Item Part No. Description 909235 Gearbox Installation 14”KTD (16” Frame) * 906765 . Gearbox Assembly R13806363 . Capscrew * 906225 . Plunger Assembly 221660W . Capscrew 904466 .
Page 38 Gearbox Installation 14”KTD (16” Frame) Page 3 of 5 24 15 34 13 14 15 PLUNGER STOP DOG 89-096 Rev: 11-2016...
Page 39 Gearbox Installation 14”KTD (16” Frame) Page 4 of 5 REF: GEARBOX REF: DRAWBAR MOUNT (RIGHT HAND) REF: PLUNGER ROD DETAIL C ROLL PIN INSTL DRIVE ARM NOT SHOWN Rev: 11-2016 89-096...
Page 40 Gearbox Installation 14”KTD (16” Frame) Page 5 of 5 WASHER DETAIL SHIMS WASHER DETAIL CAP INSTALLATION SAME FOR 904466 & 906841 SERRATED EDGES BOTH SIDES FASTENERS HAND TIGHT GAP .010" MAX WEDGE FEATURES DETAIL E WASHER DETAIL DETAIL F INSTALLATION NOTES: USE THE HARDWARE PROVIDED WITH THE ARM.
Page 41 Gearbox Installation 14”X21”KTD (16” Frame) Page 1 of 5 17 18 SECTION A-A 13 16 27 28 29 30 SECTION B-B NOTES: SHIM GEARBOX TO ALIGN CRANK ARM PIN HOLE WITH DRIVE ARM PIN HOLE IN 4 QUADRANTS IN ITS RANGE OF MOTION.
Page 42 Gearbox Installation 14”X21”KTD (16” Frame) Page 2 of 5 Item Part No. Description Item Part No. Description 909236 Gearbox Installation 14”X21”KTD (16” Frame) * 906765 . Gearbox Assembly R13806363 . Capscrew * 908708 . Plunger Assembly 221660W . Capscrew 904466 .
Page 43 Gearbox Installation 14”X21”KTD (16” Frame) Page 3 of 5 24 15 34 13 14 15 PLUNGER STOP DOG Rev: 11-2016 89-096...
Page 44 Gearbox Installation 14”X21”KTD (16” Frame) Page 4 of 5 REF: GEARBOX REF: DRAWBAR MOUNT (RIGHT HAND) REF: PLUNGER ROD DETAIL C ROLL PIN INSTL DRIVE ARM NOT SHOWN 89-096 Rev: 11-2016...
Page 45 Gearbox Installation 14”X21”KTD (16” Frame) Page 5 of 5 WASHER DETAIL SHIMS WASHER DETAIL CAP INSTALLATION SAME FOR 904466 & 906841 SERRATED EDGES BOTH SIDES FASTENERS HAND TIGHT GAP .010" MAX WEDGE FEATURES DETAIL E WASHER DETAIL DETAIL F INSTALLATION NOTES: USE THE HARDWARE PROVIDED WITH THE ARM.
Page 46 Gearbox Gearbox Assembly Page 1 of 2 Page 1 of 3 NOTES: PLACE MAGNET (R525293) IN A LOCATION INSIDE THE BOTTOM WELDMENT WHERE IT DOES NOT MAKE CONTACT WITH THE GEAR. DO NOT PAINT EXPOSED SURFACE OF SHAFTS. PRIOR TO INSTALLATION OF PINION SHAFT, MEASURE THE MOVEMENT OF THE GEAR TO CONFIRM IT MEETS THE FOLLOWING CRITERIA END PLAY: .005"...
Page 47 Gearbox Gearbox Assembly Page 2 of 2 Page 2 of 3 SENSOR PLUG RH SIDE DRAIN NOTES SHIM THIS SIDE AS REQUIRED. SHIM UNTIL THERE IS THE LEAST AMOUNT OF ENDPLAY (.003" OR LESS) WITH THE SUPPLIED SHIMS (ITEM 28 THRU 37, 41 THRU 44) PRIOR TO APPLICATION OF ANY SEALANT. LH SIDE USE SEALANT (ITEM 38) ON SURFACES BETWEEN ITEM 4 &...
Page 48 Knotter Drive Installation, Gearbox Baler Knotter Drive Installation; Gearbox Baler Page 1 of 2 Page 1 of 2 1.2.4 SECTION C-C SECTION A-A SECTION B-B 28 21 30 28 21 SECTION D-D NOTES: 1.1 - IDLER SPROCKET ALIGNED TO FOLLOW PATH OF CHAIN. CHAIN SHOULD NOT RUB KNOTTER SH REQUIRED BUT SUGGESTED QUANTITY IS SHOWN.
Page 49 Knotter Drive Installation; Gearbox Baler Knotter Drive Installation, Gearbox Baler Page 2 of 2 Page 2 of 2 28 21 30 TION C-C 15 24 DETAIL E NOTES: 1.1 - IDLER SPROCKET ALIGNED TO FOLLOW PATH OF CHAIN. CHAIN SHOULD NOT RUB KNOTTER SHAFT SPROCKET WHEN OPERATING.
Page 50 Shield Installation; LH Shielding Installation; LH Page 1 of 1 Page 1 of 1 NOTES: - USE EXISTING CAPSCREW. - SHIM USING WASHER TO ALIGN SHIELD ITEM 3 SECTION D-D DETAIL A DETAIL B SECTION C-C Item Part No. Description Item Part No.
Page 51 Shield Installation; Crank Arm Shielding Installation, Crank Arm Page 1 of 1 Item Part No. Description Item Part No. Description 906833 Shield Installation 909551 . Plate, Rear Shield 264150W . Nut 909552 . Plate, Fnt Shield 223428 . Flat Washer 903911 .
Page 52 Plunger Assy, 16”x22” Plunger Assy, 16”x22” Page 1 of 4 Gearbox Baler Page 1 of 4 18 27 24 22 23 TOP LEFT SIDE VIEW SHOWN WITHOUT CON ROD NOTES: PLUNGER KNIFE CANNOT EXTEND MORE THAN .002" PAST SIDE OF PLUNGER OR BE RECESSED MORE THAN .005"...
Page 53 Plunger Assy, 16”x22” Plunger Assy, 16”x22” Gearbox Baler Page 2 of 4 Page 2 of 4 BOTTOM VIEW Item Part No. Description Item Part No. Description 904473 Plunger Assy, 16”x22” 905083 . Plunger 247008 . Jam Nut F000008056 . Pad, Adjusting, Right R13811457 .
Page 54 Plunger Assy, 16”x22” Plunger Assy, 16”x22” Gearbox Baler Page 3 of 4 Page 3 of 4 CON ROD VIEW (FOR 14" PLUNGER ASSEMBLY) NOTES: USE SHIMS ITEMS 37, 44, AND 59 TO CENTER ITEM 40 IN PLUNGER DURING PLUNGER ASSEMBLY. INSURE RETAINING BOLTS FOR PLUNGER CONNECTING ROD PIN ARE LOCATED ON THE FLAT OF THE PIN.
Page 55 Plunger Assy, 16”x22” Plunger Assy, 16”x22” Gearbox Baler Page 4 of 4 Page 4 of 4 BOTH SIDES OF PIN BOTTOM LEFT VIEW 20 22 SHOWN WITHOUT BOTTOM PLATE 55 54 53 52 BACK VIEW SHOWN WITHOUT TOP PLATE NOTES: USE ITEMS 4 &...
Page 56 Plunger Assy, Kitted for 15”x22” Plunger Assy, Kittted for 15”x22” Gearbox Baler Page 1 of 4 Page 1 of 4 18 27 24 22 23 TOP LEFT SIDE VIEW SHOWN WITHOUT CON ROD NOTES: PLUNGER KNIFE CANNOT EXTEND MORE THAN .002" PAST SIDE OF PLUNGER OR BE RECESSED MORE THAN .005"...
Page 57 Plunger Assy, Kitted for 15”x22” Plunger Assy, Kittted for 15”x22” Gearbox Baler Page 2 of 4 Page 2 of 4 BOTTOM VIEW Item Part No. Description Item Part No. Description 906224 Plunger Assy, Kitted for 15”x22” 906333 . Plunger 247008 .
Page 58 Plunger Assy, Kitted for 15”x22” Plunger Assy, Kittted for 15”x22” Gearbox Baler Page 3 of 4 Page 3 of 4 CON ROD VIEW (FOR 14" PLUNGER ASSEMBLY) NOTES: USE SHIMS ITEMS 37, 44, AND 59 TO CENTER ITEM 40 IN PLUNGER DURING PLUNGER ASSEMBLY. INSURE RETAINING BOLTS FOR PLUNGER CONNECTING ROD PIN ARE LOCATED ON THE FLAT OF THE PIN.
Page 59 Plunger Assy, Kitted for 15”x22” Plunger Assy, Kittted for 15”x22” Gearbox Baler Page 4 of 4 Page 4 of 4 BOTH SIDES OF PIN BOTTOM LEFT VIEW 20 22 SHOWN WITHOUT BOTTOM PLATE 55 54 53 52 BACK VIEW SHOWN WITHOUT TOP PLATE NOTES: USE ITEMS 4 &...
Page 60 Plunger Assy, Kitted for 14”x22” Plunger Assy, Kittted for 14”x22” Gearbox Baler Page 1 of 4 Page 1 of 4 18 27 24 22 23 TOP LEFT SIDE VIEW SHOWN WITHOUT CON ROD NOTES: PLUNGER KNIFE CANNOT EXTEND MORE THAN .002" PAST SIDE OF PLUNGER OR BE RECESSED MORE THAN .005"...
Page 61 Plunger Assy, Kitted for 14”x22” Plunger Assy, Kittted for 14”x22” Gearbox Baler Page 2 of 4 Page 2 of 4 BOTTOM VIEW Item Part No. Description Item Part No. Description 906225 Plunger Assy, Kitted for 14”x22” 906228 . Plunger 247008 .
Page 62 Plunger Assy, Kitted for 14”x22” Plunger Assy, Kittted for 14”x22” Gearbox Baler Page 3 of 4 Page 3 of 4 CON ROD VIEW (FOR 14" PLUNGER ASSEMBLY) NOTES: USE SHIMS ITEMS 37, 44, AND 59 TO CENTER ITEM 40 IN PLUNGER DURING PLUNGER ASSEMBLY. INSURE RETAINING BOLTS FOR PLUNGER CONNECTING ROD PIN ARE LOCATED ON THE FLAT OF THE PIN.
Page 63 Plunger Assy, Kitted for 14”x22” Plunger Assy, Kittted for 14”x22” Gearbox Baler Page 4 of 4 Page 4 of 4 BOTH SIDES OF PIN BOTTOM LEFT VIEW 20 22 SHOWN WITHOUT BOTTOM PLATE 55 54 53 52 BACK VIEW SHOWN WITHOUT TOP PLATE NOTES: USE ITEMS 4 &...
Page 64 Plunger Assy, Kitted for 14”x21” Plunger Assy, Kitted for 14”x21” Page 1 of 3 Page 1 of 3 89-096 Rev: 11-2016...
Page 65 Plunger Assy, Kitted for 14”x21” Plunger Assy, Kitted for 14”x21” Page 2 of 3 Page 2 of 3 NOTES: PLUNGER KNIFE CANNOT EXTEND MORE THAN .002" PAST SIDE OF PLUNGER OR BE RECESSED MORE THAN .005" BELOW THE PLUNGER SIDE. TORQUE ITEM 17 TO 130 FT-LBS.
Page 66 Plunger Assy, Kitted for 14”x21” Plunger Assy, Kitted for 14”x21” Page 3 of 3 Page 3 of 3 43 55 43 54 43 53 43 52 44 37 59 SECTION D-D 35 31 DETAIL F LUBRICATION LINES & CON-ROD 43 53 NOTES: USE ITEM 37, 44 &...
Page 67 Connecting Rod Assy, Gearbox Baler, 15/16” 3-Tie Connecting Rod Assy, Gearbox Baler, 15/16” 3-Tie Page 1 of 1 NOTES: SHIM TO 0" TO 0.004" CLEARANCE BETWEEN BUSHING AND CONNECTING ROD BEARING MOUNT TORQUE BOLT TO 700 FT-LB TORQUE BOLT TO 309 FT-LB APPLY MOLY-KOTE TO BOLT BODY AND BUSHING ID APPLY ANTI-SEIZE TO THREADS USE LOCTITE # 242...
Page 68 Connecting Rod Assy, Gearbox Baler, 14” 3-Tie Connecting Rod Assy, Gearbox Baler, 14” 3-Tie Page 1 of 1 NOTES: SHIM TO 0" TO 0.004" CLEARENCE BETWEEN BUSHING AND CONNECTING ROD BEARING MOUNT. TORQUE BOLT TO 700 FT-LB APPLY MOLY-KOTE TO BOLT BODY AND BUSHING ID APPLY ANTI-SEIZE TO THREADS USE LOCTITE # 242 ORIENT GREASE FITTING AWAY FROM CONNECTING ROD...
Page 69 Tensioning/Rear Mnt Inst, 37X - 16” Tensioning/Rear Mounts Inst - 16” Page 1 of 4 Page 1 of 4 29 36 36 39 30 36 36 39 16" CHAMBER Item Part No. Description Item Part No. Description 909386 Tensioning/Rear Mounts Installation PLT0035077 .
Page 70 Tensioning/Rear Mnt Inst, 37X - 16” Tensioning/Rear Mounts Inst -16” Page 2 of 4 Page 2 of 4 NOTES: PART #8 AND #18 ARE MOUNTED AFTER PAINT. TYP. BOTH SIDES 32 41 DUAL RAMS AND MOUNTS 89-096 Rev: 11-2016...
Page 71 Tensioning/Rear Mounts Inst -16” Tensioning/Rear Mnt Inst, 37X - 16” Page 3 of 4 Page 3 of 4 TYP. BOTH SIDES NOTES: WORK INSTRUCTIONS ARE AVAILABLE FOR INSTRUCTION OF FRAME TIE PLATES. TYP. ONLY USED WITH 14X21 CHAMBER KITS. 3 PLACES BACK PLATE AND MOUNT PLATE 47 8X TENSION RAILS...
Page 72 Tensioning/Rear Mounts Inst - 16” Tensioning/Rear Mnt Inst, 37X - 16” Page 4 of 4 Page 4 of 4 NOTES: FASTEN WITH BLACK ZIP TIES IN SHOWN POSITION. PART #18 (TENSION BOX COVER) IS MOUNTED AFTER PAINT. SECTION H-H HOSE PROTECTOR DETAIL A BYPASS BOX TENSION PUMP &...
Page 73 Tensioning/Rear Mounts Inst - 16” Frame Ktd 15” Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-15” Page 1 of 4 Page 1 of 4 29 36 36 39 30 36 36 39 15" KITTED 906229 Item Part No. Description Item Part No.
Page 74 Tensioning/Rear Mounts Inst -16” Frame Ktd 15” Page 2 of 4 Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-15” Page 2 of 4 NOTES: PART #8 AND #18 ARE MOUNTED AFTER PAINT. TYP. BOTH SIDES 32 41 DUAL RAMS AND MOUNTS 89-096 Rev: 11-2016...
Page 75 Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-15” Tensioning/Rear Mounts Inst -16” Frame Ktd 15” Page 3 of 4 Page 3 of 4 TYP. BOTH SIDES NOTES: WORK INSTRUCTIONS ARE AVAILABLE FOR INSTRUCTION OF FRAME TIE PLATES. TYP. ONLY USED WITH 14X21 CHAMBER KITS. 3 PLACES BACK PLATE AND MOUNT PLATE 47 8X...
Page 76 Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-15” Tensioning/Rear Mounts Inst - 16” Frame Ktd 15” Page 4 of 4 Page 4 of 4 NOTES: FASTEN WITH BLACK ZIP TIES IN SHOWN POSITION. PART #18 (TENSION BOX COVER) IS MOUNTED AFTER PAINT. SECTION H-H HOSE PROTECTOR DETAIL A...
Page 77 Tensioning/Rear Mounts Inst - 16” Frame Ktd 14” Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14” Page 1 of 4 Page 1 of 4 29 36 36 39 30 36 36 39 14" KITTED Item Part No. Description Item Part No. Description 909388 Tensioning/Rear Mounts Installation...
Page 78 Tensioning/Rear Mounts Inst -16” Frame Ktd 14” Page 2 of 4 Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14” Page 2 of 4 NOTES: PART #8 AND #18 ARE MOUNTED AFTER PAINT. TYP. BOTH SIDES 32 41 DUAL RAMS AND MOUNTS 89-096 Rev: 11-2016...
Page 79 Tensioning/Rear Mounts Inst -16” Frame Ktd 14” Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14” Page 3 of 4 Page 3 of 4 TYP. BOTH SIDES NOTES: WORK INSTRUCTIONS ARE AVAILABLE FOR INSTRUCTION OF FRAME TIE PLATES. TYP. ONLY USED WITH 14X21 CHAMBER KITS. 3 PLACES BACK PLATE AND MOUNT PLATE 47 8X...
Page 80 Tensioning/Rear Mounts Inst - 16” Frame Ktd 14” Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14” Page 4 of 4 Page 4 of 4 NOTES: FASTEN WITH BLACK ZIP TIES IN SHOWN POSITION. PART #18 (TENSION BOX COVER) IS MOUNTED AFTER PAINT. SECTION H-H HOSE PROTECTOR DETAIL A...
Page 81 Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14”x21” Page 1 of 4 Tensioning/Rear Mounts Inst - 16” Frame Ktd 14” X 21” Page 1 of 4 29 36 36 39 30 36 36 39 14" KITTED Item Part No. Description Item Part No.
Page 82 Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14”x21” Tensioning/Rear Mounts Inst -16” Frame Ktd 14” X 21” Page 2 of 4 Page 2 of 4 NOTES: PART #8 AND #18 ARE MOUNTED AFTER PAINT. TYP. BOTH SIDES 32 41 DUAL RAMS AND MOUNTS 89-096 Rev: 11-2016...
Page 83 Tensioning/Rear Mounts Inst -16” Frame Ktd 14” X 21” Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14”x21” Page 3 of 4 Page 3 of 4 TYP. BOTH SIDES NOTES: WORK INSTRUCTIONS ARE AVAILABLE FOR INSTRUCTION OF FRAME TIE PLATES. TYP. ONLY USED WITH 14X21 CHAMBER KITS.
Page 84 Tensioning/Rear Mounts Inst - 16” Frame Ktd 14” X 21” Tensioning/Rear Mnt Inst, 37X - 16” Frame Ktd-14”x21” Page 4 of 4 Page 4 of 4 NOTES: FASTEN WITH BLACK ZIP TIES IN SHOWN POSITION. PART #18 (TENSION BOX COVER) IS MOUNTED AFTER PAINT.
Page 85 Tensioning/Rear Mnt Inst - 380/385, 14” Kitted Tensioning/Rear Mnt Inst - 380/385, 14” Kitted Page 1 of 2 Page 1 of 2 Rev: 11-2016 89-096...
Page 86 Tensioning/Rear Mnt Inst - 380/385, 14” Kitted Tensioning/Rear Mnt Inst - 380/385, 14” Kitted Page 2 of 2 Page 2 of 2 Item Part No. Description Item Part No. Description 905867 Tensioning/Rear Mnt Inst PLT0035077 . Bar, Upper R13811191 . Locknut TNS0034362 2 .
Page 87 Frame & Axle, 16”; Gearbox Baler Frame & Axle, 16” Page 1 of 1 DETAIL A NOTES: 1. VIEWS ARE OF 16" 3-TIE BULLGEAR FRAME. Item Part No. Description Item Part No. Description 909327 Frame & Axle Assembly 906811 . Frame, 16”; 3 Tie, Gearbox Baler AXL0030902 1 .
Page 88 Frame & Axle, 14x21”; Gearbox Baler Frame & Axle, 14 X 21” Page 1 of 1 DETAIL A NOTES: 1. VIEWS ARE OF 16" 3-TIE BULLGEAR FRAME. Item Part No. Description Item Part No. Description 909328 Frame & Axle Assembly 908289 .
Page 89 Chamber Inst, 14x21 Gearbox 3 Tie Chamber Inst, 14x21 Gearbox 3 Tie Page 1 of 7 Page 1 of 7 Item Part No. Description Item Part No. Description 908280 Chamber Inst, 14x21 Gearbox 3 Tie F000000299 . Bar, RH Y09G-0540 .
Page 90 Chamber Inst, 14x21 Gearbox 3 Tie Chamber Inst, 14x21 Gearbox 3 Tie Page 2 of 7 Page 2 of 7 RH SIDE INSTALLATION 34 53 SECTION A-A 61 39 28 44 89-096 Rev: 11-2016...
Page 91 Chamber Inst, 14x21 Gearbox 3 Tie Chamber Inst, 14x21 Gearbox 3 Tie Page 3 of 7 Page 3 of 7 SECTION B-B LH & RH RAIL INSTALLATION SECTION D-D SECTION C-C Rev: 11-2016 89-096...
Page 92 Chamber Inst, 14x21 Gearbox 3 Tie Chamber Inst, 14x21 Gearbox 3 Tie Page 4 of 7 Page 4 of 7 SECTION E-E LOWER CENTER INSTALLATION 27 43 42 40 46 42 89-096 Rev: 11-2016...
Page 93 Chamber Inst, 14x21 Gearbox 3 Tie Chamber Inst, 14x21 Gearbox 3 Tie Page 5 of 7 Page 5 of 7 SECTION H-H SECTION F-F SECTION G-G SECTION J-J Rev: 11-2016 89-096...
Page 94 Chamber Inst, 14x21 Gearbox 3 Tie Chamber Inst, 14x21 Gearbox 3 Tie Page 6 of 7 Page 6 of 7 61 39 61 39 SECTION K-K 23 69 89-096 Rev: 11-2016...
Page 95 Chamber Inst, 14x21 Gearbox 3 Tie Chamber Inst, 14x21 Gearbox 3 Tie Page 7 of 7 Page 7 of 7 61 39 SECTION M-M LH SIDE INSTALLATION SECTION N-N SECTION L-L Rev: 11-2016 89-096...
Page 96 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 1 of 11 Page 1 of 9 89-096 Rev: 11-2016...
Page 97 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 2 of 9 Page 2 of 11 Item Part Number Description Quantity F000000299 RH Upper Slide Plunger Plate F000007439 Knife Guide Under Feed Opening 905059 Bottom LH Plunger Rail 905062 Plunger, Side Rail F000007767...
Page 98 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 3 of 9 Page 3 of 11 Item Part Number Description Quantity Y09G-0516 Capscrew Y09G-0520 Capscrew Y09G-0524 Capscrew Y09G-0528 Capscrew Y09G-0532 Capscrew Y09G-0536 Capscrew Y09G-0544 Capscrew Y09G-0548 Capscrew Y09G-0556 Capscrew...
Page 99 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 4 of 11 Page 4 of 9 Item Part Number Description Quantity R13812516 Washer, Lock SQS5001750 Sq Head Set Screw 234218 Nut, Jam 903119 Needle Track Block, 14" Chamber 902703 Needle Track Block, Sq Edge Y17C-1028...
Page 100 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 5 of 9 Page 5 of 11 14" 16" 15" 14" 15", 16" LOWER CENTER FRONT NOTES: QTY CHANGE TO SUIT KITTED CHAMBER SPACERS NOT REQUIRED FOR 16" NON-KITTED BALERS. LENGTH OF FASTENERS CHANGE TO SUIT NUMBER OF SPACER REQUIRED FOR NON-KITTED BALERS.
Page 101 Chamber Installation Gearbox 3 Tie 15" 14" 16" 14x22,15x22,16x22 15" 14" 16" Page 6 of 11 15" 14" 16" 15" 14" 16" 15" 14" 16" 15" 14" 16" LOWER LEFT PLUNGER RAIL & SPACER (16", 15" AND 14" KITTED) 43 42 43 42 UPPER LOWER LEFT FRAME RAIL...
Page 102 Chamber Installation Gearbox 3 Tie Chamber Installatio 14x22,15x22,16x22 14x22,15x2 Page 7 of 11 Page 7 43 42 AS REQUIRED 15" / 16" 3X FOR 14" 16" 14" 15" 37 40 16" UPPER & LOWER FRAME RAILS 14" (16", 15" AND 14" KITTED) 15"...
Page 103 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 8 of 11 Page 8 of 9 16" 15" 14" 14" 16" 15" 36 39 NOTES: QTY CHANGE TO SUIT KITTED CHAMBER SPACERS NOT REQUIRED FOR 16" NON-KITTED BALERS. LENGTH OF FASTENERS CHANGE TO SUIT NUMBER OF SPACER REQUIRED FOR NON-KITTED BALERS.
Page 104 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 9 of 9 Page 9 of 11 FOR 370/380 SPRING MOUNT (16", 15" AND 14" KITTED) FORB375/385 SPRING MOUNT (16", 15" AND 14" KITTED) REAR CONV. SPACER FOR 14" CHAMBER (16", 15"...
Page 105 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 1 of 9 Page 10 of 11 Rev: 11-2016 89-096...
Page 106 Chamber Installation Gearbox 3 Tie Chamber Installation Gearbox 3 Tie 14x22,15x22,16x22 14x22,15x22,16x22 Page 1 of 9 Page 11 of 11 89-096 Rev: 11-2016...
Page 107 Intentionally Left Blank Rev: 11-2016 89-096...
Page 108 To find a dealer in your area, Call: 503-625-2560, Fax: 503-625-7269, or 89-096 10/2016 Visit our website: http//www.alliedsystems.com Printed in USA...