Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Download this manual
See also:
Owner's Manual
Installation Instructions
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Before attempting the installation of this kit, be sure to unplug the oven from wall receptacle.
Your oven is designed to be installed under properly constructed, good condition wood or metal cabinets that are sturdy enough to support
the items you have in the cabinet, plus an additional 41 kg (90 pounds) from the cabinet bottom.
Empty the contents of your selected cabinet and the delicate items in adjoining cabinets.
(NOTE: When drilling the holes, the vibration could cause damage to fragile items such as crystal or china.)
Now, you must inspect your cabinets. If any of the following conditions exist, then it is your personal responsibility to test the cabinets or
contact a qualified cabinet maker.
1.
Separation of joints between the bottom shelf and the cabinet structure.
2.
Splitting, cracking or other signs of deterioration.
3.
Check the number of screws used to install your cabinets. If your cabinet is attached to the wall with only two screws at the top, then
you must add two screws at the bottom to firmly secure your cabinet to the wall. When adding the screws, be sure that they enter wall
studs with at least 1.3 cm (1/2") penetration.
4.
On wood cabinets, the bottom shelf must be at least .48 cm (3/16") thick masonite or plywood.
5.
Be sure that the underside of the cabinet is at least 50 cm (20") wide and 35.0cm (13 25/32") deep. If the cabinet is less than
35.0cm(13 25/32") deep, follow the cabinet mounting instructions catefully if you desire to mount your oven under cabinet.
To test your cabinets, place a 40 KG(90LB.) load, plus the equivalent weight of items normally stored on the shelf*, for a minimum of five
minutes.
*You may consider using jugs of water, bricks or books to obtain the test load.
PLEASE NOTE: If your cabinet is properly constructed and suitably installed it will withstand this test without any damage; however, there
is the possibility of damage should the cabinet be incapable of supporting the additional load.
The Maytag Company is NOT RESPONSIBLE FOR ANY DAMAGE OR OTHER CONSEQUENCES resulting from the performance of
this test.
If you are unsure that your cabinets are suitable for this type of installation you may use the oven on your countertop.
TOOLS AND PARTS
The following tools are needed for installation of your unit:
• Drill and .64cm (1/4") drill bit
• Phillips and flat blade screwdrivers
• Nail or center punch
• Pencil and ruler
• Scissors
• Hammer
INSTALLATION PARTS LIST
The following is a list of the parts that you may need for installation of your oven.
Remove all parts from the cooking cavity and compare them with the parts list and illustration to be sure that none are missing. Use this
time to become familiar with each piece.
Part No.: 8101P611-60
Code No.: DE68-02900A
Advertisement
Table of Contents
Related Manuals for Amana AMC4080AA
Summary of Contents for Amana AMC4080AA
-
Page 1: Important Safety Instructions
Installation Instructions READ CAREFULLY. KEEP THESE INSTRUCTIONS. IMPORTANT SAFETY INSTRUCTIONS WARNING Before attempting the installation of this kit, be sure to unplug the oven from wall receptacle. Your oven is designed to be installed under properly constructed, good condition wood or metal cabinets that are sturdy enough to support the items you have in the cabinet, plus an additional 41 kg (90 pounds) from the cabinet bottom. -
Page 2: Parts List
PARTS LIST 1. 3 Sets of bolts 2. 4-washers-A 3. 4-washers-B 4. 1-Template Upon completing your check of the parts list, read all instructions completely before starting the installation. This will help you to become familiar with the process and make installation easier. (NOTE: It is suggested that you gather all needed tools and installation parts in one location.) PREPARATIONS Open the template and detach both segments along the dashed line with scissors. -
Page 3: Instructions For Drilling From Inside
DRILLING APPROACH You have two options for drilling the mounting holes for your oven. First, you can drill from inside of the cabinet if you have adequate space and your shelves are removable. Second, you can drill from the bottom. If possible, it is generally easier to work from the inside of the cabinet. -
Page 4: Drilling The Mounting Holes
• Position remaining piece of Template 2 under the cabinet and align the hole center lines with arrows on Template 1 so that the distance from right hole center to left hole center measures the distance indicated on the templates. (You may have to cut excess paper from middle of the template to make it lay flat.) •... -
Page 5: Instrucciones De Seguridad Importantes
Instrucciones de instalación LÉALAS DETENIDAMENTE. Conserve estas instrucciones. INSTRUCCIONES DE SEGURIDAD IMPORTANTES ADVERTENCIA Antes de comenzar la instalación de este kit, asegúrese de que el horno esté desenchufado. Este horno se ha diseñado para su instalación bajo armarios de madera o metal apropiados y bien acondicionados, lo suficientemente resistentes como para soportar los elementos que desee colocar dentro de ellos más un peso adicional de 41 kg colgado de la parte inferior. -
Page 6: Lista De Componentes
LISTA DE COMPONENTES 1. 3 juegos de tornillos 2. 4 arandelas-A 3. 4 arandelas-B 4. 1 plantilla Cuando haya acabado de comprobar la lista de componentes, lea completamente las instrucciones antes de comenzar la instalación. Esto le ayudará a familiarizarse con el proceso y hará que la instalación le resulte más fácil. (NOTA: Le sugerimos que reúna todas las herramientas necesarias y los componentes de la instalación en un solo lugar.) PREPARACIÓN Abra la plantilla y separe los dos segmentos a lo largo de la línea de puntos con ayuda de unas tijeras. - Page 7 MÉTODOS DE TALADRADO Existen dos opciones para perforar los orificios de montaje para el horno. La primera consiste en perforar desde el interior del armario, en caso de que disponga del espacio adecuado para hacerlo y de que los estantes sean desmontables. La segunda consiste en perforar desde la parte inferior.
-
Page 8: Montaje Del Horno
• Coloque la otra pieza de la plantilla 2 debajo del armario y alinee las líneas del centro de los orificios con las flechas de la plantilla 1 de manera que la distancia desde el centro del orificio derecho al centro del orificio izquierdo coincida con la distancia indicada en las plantillas.