Download
Share
Print this page
Pro's Kit FB-1688 Manual
  1. Manuals
  2. Brands
  3. Pro's Kit Manuals
  4. Tools
  5. FB-1688
  6. Manual

Pro's Kit FB-1688 Manual

Fiber cleaver
Hide thumbs

Advertisement

Quick Links

Download this manual
FB-1688 FIBER CLEAVER
Thanks for buying PRO'SKIT FB-1688 Fiber Cleaver.
Please read these instructions carefully before using the
product.
This product has been designed and manufactured to
assure personal safety.
Improper use can result in bodily injury and serious
damage to fiber cleaver.
Please read and observe all warning instructions given in
this operation annual.
1.
Do not disassemble or lubricate any parts of cleaver.
Doing so could cause serious damage to the cleaver.
2.
The FB-1688 is a precision tool. Do not impact the
cleaver by hitting or dropping it. Doing so may cause
personal injury and loss of cleaving performance.
3.
Glass fiber fragments are extremely sharp. Handle
with care. Wear safety glasses at all times during
cleaving operation for protection from glass fiber.
4.
Dispose of glass fiber fragments properly.
5.
The blade of cleaver is extremely sharp. Do not touch
it with bare hands.
6.
Do not impact the Clamp Cover. Doing so could
cause damage to cleaver and loss of cleaver
performance.
7.
If cleaver is damaged or problem occurs, please
contact our maintenance service center.

Advertisement

loading
Need help?

Need help?

Do you have a question about the FB-1688 and is the answer not in the manual?

Questions and answers

Related Manuals for Pro's Kit FB-1688

Summary of Contents for Pro's Kit FB-1688

  • Page 1 Do not disassemble or lubricate any parts of cleaver. Doing so could cause serious damage to the cleaver. The FB-1688 is a precision tool. Do not impact the cleaver by hitting or dropping it. Doing so may cause personal injury and loss of cleaving performance.

  • Page 2: Specification

    SPECIFICATION Cladding Diameter 125 μm Fiber Count Coating Diameter Single fiber 250μm & 900μm Cleave length 5-20mm Dimensions 62 x 60 x 56 mm Cleaver Blade 16 points (5FB-1688-BLAD) STRUCTURE Clamp cover Blade carriage Lip of the fiber holder Clamp Fiber holder Body Blade...

  • Page 3: Operating Procedure

    OPERATING PROCEDURE Open the Clamp Cover and lid of the fiber holder. Please make sure the blade carriage is in the forward position. Insert the fiber cable into the correct groove depending on the fiber coating diameter. Close the lid of the fiber holder and clamp cover. Slide the blade carriage to the rear side of the cleaver.
  • Page 4 Open the Clamp Cover. Open the lid of fiber holder and lift out the newly cleaved fiber. Lift the off-cut and dispose of it properly. CLEAN To keep excellent cleaving quality, please clean the fiber cleaver a fter use. USE a cotton swab moistened with isopropyl alcohol to clean the blade edge, the rubber of the clamp and anvil, the...
  • Page 5 CAUTION • Dust on the blade edge or clamp might cause loss of cleaving performance or poor quality of fiber end face. • Do not clean them with any other kind of chemicals. • If the Clamp Cover is closed leaving an off-cut fiber on the clamp, the rubber pad of clamp w have a trace of fiber, causing loss of cleaving performance or poor quality of fiber end face.
  • Page 6 CAUTION • Do not rotate the blade with hands. • Do not rotate the blade with metallic tweeze Doing so may damage the blade. T hten the blade set screw. y and cleave the fiber. Perform a visual check of the fiber end face with splicer.
  • Page 7 ADE REPL ACEMENT Unscrew the blade set screw. (Fig6) Remove the blade with tweezers (Fig.7). Fig.6 Fig.7 CAUTION The edge of a blade is manufactured precisely. If the edge is hit against metallic object, it will crack, resulting in poor cleaving performance. Handle with care.

  • Page 8: Troubleshooting

    TROUBLESHOOTING If the cleaving problems occur, the following are possible are causes. Situation Solution The fiber is placed Make sure that the fiber is obliquely in cleaver. placed straight in the cleaver The blade position is too Adjust the blade height. high.
  • Page 9 B-1688 使用說明 謝您購買和使用 PR O’SKIT FB-1688 光纖切斷刀，使用 感 前 請仔細閱讀說明書， 閱讀後請 妥善保存，以備查閱。 使 用方法和安全操作規 則 . 請不要自行拆解本產品 ，以 免造成產品損壞 . 切勿猛烈撞 擊切割刀或跌落 ， 以免成產品損壞或是影響切 割的精度 . 使用時請戴手套以避免 被刀片 或是光纖的利角割傷 . 切勿弄濕切割刀。 切勿把切割 刀放在潮濕或佈 滿灰塵的地方。 5. 常溫下保存以免高溫引起變形。 6. 裸光纖留長約 12mm。 規格...
  • Page 10 產品說明 蓋板 切割滑塊 壓纖板 光纖夾具 光纖壓墊 刀體 刀片...
  • Page 11 操作步骤 打開壓纖板及蓋板，將切割滑塊推至前端（如圖） 2. 將剝除好塗覆層的裸光纖放置於夾具內（250μm / 900μm）, 根據使用者需要確定好切割長度。按下合上 壓纖板及蓋板固定光纖。 3. 關上蓋板後確保光纖處於水準線上。 。 切割滑塊一次性向後推動，完成切割...
  • Page 12 5. 打開蓋板及壓纖板，取出光纖；光纖取出後光纖端面請 勿接觸任何物體，以免損壞光纖。 皮線光纖線的切割使用 移除圖示固定光纖夾具的螺絲. 將適合皮線光纖使用的夾具(請依據需求自行購買)放置 底座內。...
  • Page 13 將剝除外皮的光纖線放置在夾具內, 設定好需要的長度, 進行切割。 注 ：光纖細小但尖硬, 請注意切 割後剩餘光纖的收集處理, 以 免造成意外傷害. 清潔 切割完成後，請清理切 割後的斷纖，用棉花棒 沾酒精清潔壓纖板上的 污垢，切勿用丙酮或或 有腐蝕性的溶劑清理壓 纖板。切勿損壞刀片， 以備日後 使用。 定期用棉花棒沾酒精清 潔壓纖板上的污垢，切勿用丙酮或有腐蝕性的溶劑清 理壓纖板。 載纖槽要時常清潔，確保槽內無灰塵及油垢，以免影 響切割品質。...
  • Page 14 刀片的更換及調整 刀片上註明 0-15 個切割點。 當切割刀不能正常使用時，請即時清理刀片及光纖夾具 （切勿使用酒精擦拭光纖壓墊） 如果仍然不能正常切割，說明切割刀片切割點已經磨損 不能繼續使用。 調整刀片位置時請根據以下步驟使用。 A. 調整刀片（按刀片上註明的 0-15 面依次轉 動） 自備 “一”字型螺絲刀一把。 首先用“一”字 型螺絲刀將刀片上的螺絲轉鬆,如圖一 使用棉花棒轉動刀片調整刀片位置，每次轉動一個 面 ，轉動方式依箭頭指示,如圖二。 完 成後將刀片固定如仍然 無法正常切割，需要按以 下步驟調整刀片及切割滑 塊的高度。 圖一 圖二 B.調整刀片高度 採用內六角扳手，將刀片下方的兩顆內六角螺絲轉鬆，如 圖三 。 微調右圖 所示的螺絲。順時針方向調為升高刀片，反之為 降低刀片高度, 如圖四。...
  • Page 15 採用內六角扳手，將刀 片下方的兩顆內六角螺絲鎖緊, 如 圖五。 打開壓纖板及蓋板，將剝除好塗覆層的裸光纖放置於夾具 內 （125mm/900mm） ，按下合上壓纖 板,來回推動切割刀 推塊，看切割刀刀片是否正好碰到光纖，如果末碰到，重 第 2 步，調高刀片 ，如果碰到太多，重複第 2 步，降低 複 刀片。 調整好最佳位置，用內六角擰緊第一步的 鬆開的 兩個內六角。 圖三 圖四 圖五 更換新刀片 1. 首先用“一”字型螺絲刀將刀片上的螺絲拆下如圖六，將舊 刀片以鑷子夾起，並且裝上新刀片後將螺絲鎖上, 如圖 七。 按調整刀片高度步驟進 行調節 刀片的高低。 圖六 圖七...
  • Page 16 注：請不要用不合適的一字及內六角螺絲刀進行調節切割 刀。 簡 易問題排除 如 果切割刀發生問題，可能是以下的原因 問 題 排 除 方 法 光纖放置歪斜 確認光纖筆直放 進切割刀槽座中 刀片位置過高 調整刀片高度 光纖壓墊髒污 清潔光纖壓墊 切割刀片髒污 清潔切割刀片 光纖壓墊髒污 將光纖取下並且重新剝皮及清潔 光纖 PROKIT’S INDUSTRIES CO., LTD. http://www.prokits.com.tw E-mail:pk@mail.prokits.com.tw ©2013 Copyright by Prokit’s Industries Co., Ltd(C).