1. Manuals
  2. Brands
  3. ThermoSphere Manuals
  4. Electric Heater
  5. EH-4610
  6. Instruction manual

ThermoSphere EH-4610 Instruction Manual

Hide thumbs

Advertisement

Table of Contents

Instruction Manual
Heavy Electric Utility Heater
PET OWNERS WARNING:The health of some small pets including
birds are extremely sensitive to the fumes produced during the first-time use
of many appliances. These fumes are not harmful to humans but we
recommended that you do not use your heater around birds and small pets
during its initial use until the manufacturing corrosion coatings burn off.
MODEL:EH-4610
Technical Support : 1-866-206-0888
Service email: info@mecanair.net

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EH-4610 and is the answer not in the manual?

Questions and answers

Related Manuals for ThermoSphere EH-4610

Summary of Contents for ThermoSphere EH-4610

  • Page 1 Instruction Manual Heavy Electric Utility Heater MODEL:EH-4610 PET OWNERS WARNING:The health of some small pets including birds are extremely sensitive to the fumes produced during the first-time use of many appliances. These fumes are not harmful to humans but we recommended that you do not use your heater around birds and small pets during its initial use until the manufacturing corrosion coatings burn off.

  • Page 2: Important Instructions

    IMPORTANT INSTRUCTIONS When usi n g el e ctri c al appl i a nces, basi c precauti o ns shoul d 9.To disconnect the heater, turn the controls to the off position and shut al w ays be fol l o wed to reduce the ri s k of fi r e, el e ctri c shock, off the heater circuit power at the main disconnect panel.

  • Page 3: Specifications

    DESCRIPTION Electric utility heaters are designed to meet a variety of heating The mounting structure and the anchoring hardware requirements by switching a few wires located in the base of the must be capable of reliably supporting the weight of unit.

  • Page 4: Installation

    IN STALLATIO N MOUNTIN G THE BRACKET Refer to Figures 4a and 4b. Locate a stud in the ceiling joist. Remove the mounting bracket from the heating unit by loosening bracket screws with a wrench and slipping the handle off over the screw heads. Place a washer on screws before inserting through the holes in the mounting bracket,and screw them securely into a ceiling or wall joist.

  • Page 5: Single- Phase

    Connect the wire to the power block located in the base of the heater See Figure 7a and Figure 7b Turn on the power at the main service Caution High temperature risk of fire keep electrical cords drapery furnishings and other combustibles at least 3 feet from the front of the heater and away from the side and rear Caution...
  • Page 6 MULTIPLE VERTICAL ANGLES CEILING 90degrees 60degrees Fig ure 8a WALL WALL 90degrees 60degrees Figure 8b...

  • Page 7: Connecting The Power

    CONNECTING THE POWER NOTE: 1: The heater equipped with a single-phase power supply, using with a three-phase power supply, the L1(red wire) and L3(blue wire)(see Figure 9a) must be connected to the L2(see Figure 9b). 2: If using an external thermostat, the selection switch in the control panel must be set to the external thermostat( ).(see Figure 9c).

  • Page 8: Thermal Cutout

    OPERATIN G IN STRUCTIO NS ADJUSTIN G AIR FLOW DIR ECTIO N SETTIN G THE THERMOSTAT Turning the Unit IF the unit has been installed with Rotate thermostat knob clockwise to high position a single lag bolt as shown in the Figure 4a simply turn the entire unit as needed to adjust air flow After room reaches desired comfort level...

  • Page 9: Selection Switch

    SELECTION SWITCH built-in External thermostat thermostat Using the SELECTION SWITCH: I for built-in thermostat, for external thermostat . SELECTION SWITCH THERMAL CUT-OUT The heater will automatically shut off when parts of it overheat. The heater will turn on again when the abnormal temperature returns to normal levels.

Table of Contents

Save PDF