Subscribe to Our Youtube Channel
Summary of Contents for finder 19 Series
- Page 1 KNX Actuator 19.6K FINDER S.p.A. Via Drubiaglio, 14 - 10040 ALMESE (TO) - ITALY Tel. +39 011 9346211 Fax +39 011 9359079...
-
Page 2: Table Of Contents
ETAILED DESCRIPTION OF THE GENERAL CONFIGURATION PARAMETERS 1.12.1 PAR_Value Force ALL Out ........................... 16 1.12.2 PAR_Enable Keyboard ............................16 1.13 LED ............................16 EHAVIOR OF HANNEL 1.14 ..........................17 CHEME AND FUNCTIONAL PRIORITIES KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 3: Device Template
PAR_Light Time (s) PAR_Enable Logic Function PAR_Logic Operator PAR_Value PORT Locked PAR_Enable Scenes PAR_Scene Y Number PAR_Scene Y Value PAR_Enable Storage for Scene Y PAR_Value Force Out General Parameters PAR_Value Force ALL Out PAR_Enable Keyboard KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 4: Product Name And Application Name On Descriptor
1.1 Product name and Application name on descriptor Product Application 6 Channels Switch Actuator 16A 250V 19.6K Finder Application for Switch Actuator 1.2 Functional priorities DPT_Channel ALL Force ALL Out Operating highest priority DPT_Channel X Force Out Operating medium priority... -
Page 5: List Of Communication Objects
(5): it appears on product descriptor only if the 1.4.1 Behavior during the initialization, the Restart and the Bus Recovery. During the initialization, the Restart and the Bus Recovery, no Communication Object is sent on the Bus. KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 6: Detailed Description Of The Communication Objects
OFF state, turning off the lights and sends the DPT_Channel X - Status = Off message. In the figure are not shown the DPT_Channel X - Status Inverted messages that are sent as well from the device in correspondence with the status changing. KNX Actuator 19.6K FINDER SpA Ver. 2018... - Page 7 The functioning with the PAR_Function is similar. In this case the delay starts by receiving the DPT_Channel X Set ON/OFF = Off message, while the activation takes place immediately. KNX Actuator 19.6K FINDER SpA Ver. 2018...
-
Page 8: Dpt_Channel X Force Out (1.001 Switch)
Switch, except for the case where the channel function is "Stairs lights" that, if lights were lit by forcing, they will turn off after the period set with the PAR_Stairs Light Time (s) parameter. KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 9: Dpt_Channel X Select Scene (18.001 Dpt_Scene Control)
These messages allow to change run-time the thresholds set by the PAR_Upper Threshold and PAR_Lower Threshold parameters without overwriting them. They only appear on the device descriptor if the PAR_Enable Logic Function chosen by the PAR_Logic Operator KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 10: Dpt_Channel X On Delay (S) And Dpt_Channel X Off Delay (S) (7.005 Timeperiodsec)
Set ON/OFF PAR_Lower Threshold), the logical input value will be FALSE. 1.6.1.1 Logical function PORT (FLIP-FLOP) By setting the PAR_Logic Operator switching status depends by the DPT_Channel X Lock PORT message the device receives. KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 11: List Of Parameters Of The Channel Configuration Page
Enable logical block PAR_Logic Operator Logical operator when logical block is enabled. Values can be AND, OR, XOR, PORT, THRESHOLD PAR_Enable Scenes Enable/Disable scene configuration PAR_Value Force Out Forcing status with medium priority KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 12: List Of Parameters Of The Channel Scenarios Configuration Page
Enable or disable overwriting Channel value (learn) for scene 3 PAR_Scene4Number No scene number PAR_Scene4Value Value of Channel for scene 4 (On/Off) PAR_EnableScene4Storage Enable or disable overwriting Channel value (learn) for scene 4 KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 13: List Of General Configuration Parameters (Valid For Each Channel)
It defines the waiting time in seconds from the reception of the DPT_Channel X Set ON/OFF = On message before switching a channel in the ON status. Default value is 5. The maximum value is a waiting of about 18 hours. KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 14: Par_Off Delay (S)
PAR_Logic Operator parameter. KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 15: Par_Logic Operator
Property Datatype: PDT_UNSIGNED_8bit • Datapoint Type: enumerated • Range: [0÷1] It set the channel status expected for the Y scenario. Default value 0 corresponds to the OFF status, while value 1 corresponds to ON status. KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 16: Par_Enable Storage For Scene Y )
Relay is in OFF condition Table 5 (*) The status of the relay contacts will depend on the setting of the Par_Contact Type parameter, if is set on NC, the configuration results inverted. KNX Actuator 19.6K FINDER SpA Ver. 2018... -
Page 17: Scheme And Functional Priorities
1.14 Scheme and functional priorities KNX Actuator 19.6K FINDER SpA Ver. 2018...
Need help?
Do you have a question about the 19 Series and is the answer not in the manual?
Questions and answers