Related Manuals for ORTEC 4002D
Summary of Contents for ORTEC 4002D
- Page 1 740300 ORTEC Model 4002D Operating and Service Manual ORTEC Model 4002D NIM Bin Power Supply Operating and Service Manual Printed in U.S.A. ORTEC Part No. 740300 19-0429 Manual Revision K...
- Page 2 In the event ORTEC fails to manufacture or deliver items called for in this agreement or purchase order, ORTEC’s exclusive liability and buyer’s exclusive remedy shall be release of the buyer from the obligation to pay the purchase price.
-
Page 3: Safety Instructions And Symbols
740300 ORTEC Model 4002D Operating and Service Manual Copyright © 2009, Advanced Measurement Technology, Inc. All rights reserved. ® *ORTEC is a registered trademark of Advanced Measurement Technology, Inc. All other trademarks used herein are the property of their respective owners. -
Page 4: Table Of Contents
1. DESCRIPTION ............................ 7 2. SPECIFICATIONS ..........................8 3. INSTALLATION……………………………………………………………………………………………………………………..……10 3.1 UNPACKING……………………………………………………………………………………………………………………..11 3.2 SELECTING THE MAINS VOLTAGE……………………………………………………………………………………..11 3.3 CONNECTION OF THE 4002D TO A NIM BIN………………………………………………………………………11 3.3.1 Requirements for Attached Bin………………………………………………………………………..……11 3.3.2 Instructions for Attaching Bin……………………………….……………………………….………………11 4. OPERATING INSTRUCTIONS………………………………………………………………………………………………………13 5. CIRCUIT DESCRIPTION…………………………………………………………………………………………………………….…14... - Page 5 740300 ORTEC Model 4002D Operating and Service Manual SAFETY WARNING AND CLEANING INSTRUCTIONS WARNING: If this equipment is used in a manner not specified by the manufacturer the protection provided by the instrument may be impaired. CLEANING INSTRUCTIONS To clean the instrument exterior: •...
- Page 6 740300 ORTEC Model 4002D Operating and Service Manual...
-
Page 7: Description
Type V-H supplies as defined in DOE/ER-0457T. Regulated dc power supplied to the attached bin by the 4002D is conservatively rated at +6 V @ 10 A, - 6V@10A,+12V@3A,-12V@3A,+24V@ 1.5A, and -24 V @ 1.5 A. These maximum output currents can be delivered in any combination provided the total output dc power does not exceed 160 W at ambient temperatures up to 50̊... -
Page 8: Specifications
740300 ORTEC Model 4002D Operating and Service Manual SPECIFICATIONS INPUT 115V-120V or 220V-240V, 50/60 HZ, 490 VA (plus any load on 115 V ac OUTPUT). An external slide switch selects nominal input voltages of 115 or 220 V ac. DC OUTPUTS Maximum rated output currents are:... - Page 9 740300 ORTEC Model 4002D Operating and Service Manual approached. This warning occurs at and above a heat sink temperature of 95˚C. All dc outputs include a current foldback circuit to limit the output current to nominally 120% of the rated value. This feature provides short-circuit and overload protection.
-
Page 10: Installation
Check the voltage level to be used and select the appropriate range on the 4002D Power Supply. The normal selection is either 115 V ac or 220 V ac, and the selection is made using the slide switch on the side of the power supply near the power cord. -
Page 11: Instructions For Attaching Bin
Power Supply will be mounted to the adapter blocks. 3. Using the ORTEC 4001A/C Bins, mount the adapter block with an "R" on top to the side of thebin that has the On/Off switch, using two 10-32 screws and lockwashers. Next, mount the adapter block with an... - Page 12 Power Supply will closely butt to the back of the bin. 7. When using older ORTEC bins, or those manufactured by other vendors, the orientation of the adapter blocks may need to be changed to ensure that the Power Supply will closely butt to the back of the bin.
-
Page 13: Operating Instructions
740300 ORTEC Model 4002D Operating and Service Manual 4. OPERATING INSTRUCTIONS The available current from the power supply is specified in Section 2, "DC OUTPUTS." Care must be used to ensure natural convection of heat dissipation by the heat sinks and power transformer. When used at maximum power loading on a bench or tabletop, the bin and power supply should be in an open space, placed upon blocks at least 1 in. -
Page 14: Circuit Description
ORTEC Model 4002D Operating and Service Manual 5. CIRCUIT DESCRIPTION The 4002D Power Supply produces six dc output voltages. A power transformer changes the input ac line voltage into six separate low-voltage sources. The sources or windings are full-wave-rectified, capacitor-filtered, and regulated by electronic series regulator circuits. The regulator circuits provide short-circuit and current limiting protection. - Page 15 740300 ORTEC Model 4002D Operating and Service Manual...
Need help?
Do you have a question about the 4002D and is the answer not in the manual?
Questions and answers