Summary of Contents for GEHEIT PN 1
- Page 1 Spray Gun PN 1 / PN 1A Operating Manual Geheit GmbH Benzstraße 2 D – 72636 Frickenhausen Germany Phone: + 49 (0) 7022 78969021 Fax: +49 (0) 7022 78969029 www.shop.geheit.de...
- Page 2 Hiermit erklären wir, dass die We declare herewith that the NIEDERDRUCKSPRITZPISTOLE (PN 1 / PN 1A) HVLP SPRAY GUN (PN 1 / PN 1A) Gemäß der folgenden Maschinenrichtlinien konstruiert und gebaut wurde: Is constructed and produced according to the following Machinery Directives:...
-
Page 3: Table Of Contents
All rights reserved, but particularly the right of duplication, distribution and translation. No part of this publication may be reproduced in any form (printed, photocopying, microfilming or by any other method) without the previous written consent of Geheit GmbH, or be stored, processed, duplicated or distributed by means of electronic... -
Page 4: Intended Use
ABAC low pressure paint-spraying units. As a part of original ABAC units, the ABAC Spray Gun PN 1 / PN 1A should work only in combination with ABAC SG 2000, ABAC SG 2500 and ABAC SG 3001 blowers. It is prohibited to use this spray gun together with blower units, where operating air is also applied for motor cooling (for example, with blower ABAC SG 90). -
Page 5: Brief Description
The flow of air atomizes the paint at the air-head. The amount of paint sprayed is adjustable with the setting screw (Fig. 3, item 316). The trigger of the PN 1 / PN 1A Spray Gun has two positions: ● 1... -
Page 6: Technical Data
Technical Data Mean sound level, DIN 45635, when connected to SG 2000 blower 83 dB (A) 21 °C Only for paints and solvents with a flash point above Maximum permissible operating pressure 0,45 bar Length approx. 180 mm Width approx. 110 mm Height approx. -
Page 7: Safety Notes
● The ABAC Spray Gun PN 1 / PN 1A should only be used for its intended purpose and when it is in a perfect working order. The user must be safety conscious, fully aware of the risk, and follow the operating instructions. -
Page 8: Safe Operation
● When working in confined spaces, these must be properly ventilated using effective technical ventilation systems. ● The ABAC Spray Gun PN 1 / PN 1A is not splash-proof. It must not be used out of doors, when it is raining or splashed or washed with water or immersed in liquid. -
Page 9: Transportation And Storage
Transportation and storage The ABAC Spray Gun PN 1 / PN 1A is supplied in a cardboard box. To avoid damage during transportation and storage, we recommend to use this original packaging. Store your equipment in a dry ventilated room. -
Page 10: Selecting The Correct Nozzle
● Test the viscosity with the dipper as follows: After thinning the paint or lacquer to spraying consistency, immerse the dipping cup until it is full to the brim. To test, take the cup out quickly and count the number of seconds until all the paint has flowed through the 4 mm nozzle, that is to say, up to the moment, when there is a break in the outflow of paint. -
Page 11: Setting The Paint Jet
6.4 Setting the Paint Jet ● To set the paint jet to a wide jet or a circular section jet (see Fig. 2) first loosen the nozzle ring (Fig. 3, item 321), then turn air distributor of the air-head (Fig. 3, item 320) to the desired position. -
Page 12: Filling The Paint
After Paint Spraying has Finished After you have finished spraying, turn off the ABAC low-pressure blower. Then disconnect the air hose from the insulating handle of the ABAC Spray Gun PN 1 / PN 1A. Clean the spray gun as described in section 8.1. -
Page 13: Changing The Nozzle
Clean the brim of the container and the lid with seal carefully with a soft cloth or brush using a suitable thinner. On no account use sharp-edged tools as these may damage the seal and the surface of the container. Dried paint residues on the air-head (Fig. -
Page 14: Replacing The Seal Packing
Replacing the Seal Packing To replace the seal packing proceed as follows: Unscrew spring bushing (Fig. 3, item 310) from spray gun housing (Fig. 3, item 301) and remove it together with the nozzle needle (Fig. 3, items 311 to 313). Withdraw the trigger (Fig. -
Page 15: Faults, Possible Causes And Remedies
Faults, Possible Causes and Remedies Attention! Never use hard or sharp-edged tools for cleaning!!! Fault Possible causes Remedy · Packing seal of nozzle needle · Clean the spray gun, tighten Paint flows into the spray gun housing either leaking or defective or change nozzle needle seal (packing) ·... -
Page 16: Operating Instructions
ABAC Spray Gun PN 1 / PN 1A. This operating instruction is to be displayed in a suitable public place at the workplace and to be read and observed by all... -
Page 17: Spare Parts
Spare Parts For safety reasons you should only use ABAC original accessories and ABAC original spare parts. Spare parts are available from your ABAC specialist dealer or direct from us. For speedy and efficient ordering of spare parts we require the following details: ·... - Page 18 Spare Parts List for ABAC PN 1 Spray Gun (Identification number BJ 381 000 0021) (Figure 3) Fig. No. Quantity Designation Ident Number Housing HE 381 100 00 02 Insulating Handle HE 300 166 03 30 Nozzle Adapter HE 300 161 15 14...
- Page 19 Spare Parts List for ABAC PN 1A Spray Gun (Identification number BJ 381 000 0020) (Figure 3) Fig. No. Quantity Designation Ident Number Housing (nickel plated) HE 381 100 00 01 Insulating Handle HE 300 166 03 30 Nozzle Adapter HE 300 161 15 14 Trigger (nickel plated) B0 381 100 00 12...
- Page 20 Figure 3...
-
Page 21: Special Accessories
Special Accessories Fig. No. Quantity Designation Ident Number 0.2 mm diameter nozzle HE 300 161 20 51 0.3 mm diameter nozzle HE 300 161 20 52 0.5 mm diameter nozzle HE 300 161 20 53 0.8 mm diameter nozzle HE 304 161 20 02 1.2 mm diameter nozzle HE 300 161 20 08 1.8 mm diameter nozzle... -
Page 22: Flexible Joint Between Gun Housing And Paint Container
12.1 Flexible joint between gun housing and paint container (Fig. 4 and 5) To spray upwards whilst keeping the paint container vertical, use the flexible joint (Fig. 4, item 201) available as a special accessory. Flexible joint installation order: First, withdraw the angle-piece (Fig. 3, item 327) from the paint container lid and dismantle the pressure hose (Fig. -
Page 23: Extension Pipe For Spraying Points That Are Not Readily Accessible
90 Extension pipe installation order: Unscrew the nozzle coupling nut (Fig.3, item 321) from the ABAC Spray Gun PN 1 / PN 1A. Now remove the air head (Fig.3, item 320) and nozzle (Fig.3, items 317, 318, 319). -
Page 24: Annex
Annex Notes on processing and settings data for spraying tasks using ABAC Spray Gun PN 1 / PN 1A, measured with 4 mm dipper cup for viscosity checks at a spray material temperature of 20°C/70°F. Spray Material Nozzle Jet / Pattern...