Advertisement

Quick Links

T-Link-EV5273/5276/5250
User Manual
Rev
0.90
tenx reserves the right to change or discontinue the manual and online documentation to this product herein to improve
reliability, function or design without further notice. tenx does not assume any liability arising out of the application or use of
any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. tenx
products are not designed, intended, or authorized for use in life support appliances, devices, or systems. If Buyer purchases or
uses tenx products for any such unintended or unauthorized application, Buyer shall indemnify and hold tenx and its officers,
employees, subsidiaries, affiliates and distributors harmless against all claims, cost, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use even if such claim alleges that tenx was negligent regarding the design or manufacture of the part.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T-Link-EV5273 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for T-Link T-Link-EV5273

  • Page 1 T-Link-EV5273/5276/5250 User Manual 0.90 tenx reserves the right to change or discontinue the manual and online documentation to this product herein to improve reliability, function or design without further notice. tenx does not assume any liability arising out of the application or use of any product or circuit described herein;...
  • Page 2: Amendment History

    T-Link-EV5273/5276/5250 User Manual AMENDMENT HISTORY Version Date Description V0.90 Nov, 2016 New release. UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 3: Table Of Contents

    3. T-Link-EV5273/5276/5250 Hardware Description ............5 4. How to start using T-Link-EV5273/5276/5250 simulation ..........7 5. How to use four wires to program or simulate by T-Link Board ........18 6. How to update tenx IDE & T-Link F/W ................19 7.
  • Page 4: Outline

    2. Introduction Figure 2-1 is T-Link-EV5273/5276/5250 development board, the left portion is called EV5273/5276/5250 Board and the right portion is called T-Link ICE Board to connect PC to use, the user can simulate TM52F5273/5276/5250 through this development board, please refer to TM52F5273/5276/5250 datasheet in detail.
  • Page 5: T-Link-Ev5273/5276/5250 Hardware Description

    EXT_Power Internal Power USB or 3.3V T-Link Board 3.2 USB Connecter  P3: Mini USB connector to PC (T-Link Board) 3.3 Reset Button Reset: Reset Button (EV5273/5276/5250 Board)  3.4 External Power Connecter P6: External VCC connecter (EV5273/5276/5250 Board) ...
  • Page 6 T-Link-EV5273/5276/5250 User Manual 3.6 PIN Assignment & Description EV5273/5276/5250 Board contains TM52F5273/5276 main chip, packaged is SOP 32-pin (TM52F5273/76) ; SOP 20-pin (TM52F5250) as shown below table for the pin assignment instructions. TM52F5273/76 SOP 32-pin: Pin Number Pin Name Pin Number Pin Name TK14/P2.4...
  • Page 7: How To Start Using T-Link-Ev5273/5276/5250 Simulation

    T-Link-EV5273/5276/5250 User Manual 4. How to start using T-Link-EV5273/5276/5250 simulation First, Install the tenx TM52Dll IDE file to follow steps to complete the installation, the IDE & Keil C version must be installed in the same path, the default path is C: \Keil: 4.1 Select Keil C version, click “Next>”...
  • Page 8 T-Link-EV5273/5276/5250 User Manual 4.2 And then click “Next>” 4.3 The default path is C: \Keil, click “Next>” UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 9 T-Link-EV5273/5276/5250 User Manual 4.4 Click “Install” 4.5 Click “Finish” to complete the installation UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 10 T-Link-EV5273/5276/5250 User Manual 4.6 Connect T-Link-EV5273/5276/5250 Board of USB (mini type) connector to PC 4.7 Confirm Device Manger UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 11 T-Link-EV5273/5276/5250 User Manual 4.8 Open the KEIL CClick the Project menu and select New Project windowFill in the project name and click Save ProjectCopy tenx 8051 Startup Code or not? UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 12 T-Link-EV5273/5276/5250 User Manual 4.9 CPU Data Base selection dialog box will be show upSelect the tenx F8051 Devices and click on OK buttonSelect a CPU model (for EV Board model), refer to Note (1) and the right window shows some of the parameters of this single chip model.
  • Page 13 T-Link-EV5273/5276/5250 User Manual 4.10 Option for Target dialog box settings: Click the “Option for Target” button in the main menu, the project file is created must also be relevant to the project file settings as shown below. 4.11 Output dialog box settings: To confirm “Create HEX File” option is checked, as shown below.
  • Page 14 T-Link-EV5273/5276/5250 User Manual Unchecked “Use Memory Layout from Target Dialog” in BL51 4.12 BL51 Locate dialog box settings: Locate option and fill in Code & Xdata Range (Note: The chip code available range has divided into download mode and debug mode, please refer to Note (2) )
  • Page 15 T-Link-EV5273/5276/5250 User Manual 4.13 Debug dialog box settings: Click on “Use: ”option, and then select “tenx F8051 Driver” as shown below. 4.14 Utilities dialog box settings: Click on “Use Target Driver for Flash Programming” option and select “tenx F8051 Driver” as shown below.
  • Page 16 T-Link-EV5273/5276/5250 User Manual 4.15 Click on “settings” button and the “Flash Download Setup” window will be show up, check the “Download Function” desired option as shown below. 4.16 Click on “Option” button, and the “Smart Option” will be show up, about the option configuration, please refer to TM52F5273/5273/5250 datasheet.
  • Page 17 T-Link-EV5273/5276/5250 User Manual lick on “OK” to return to “Flash Download Setup” window, and then click on “OK” to return to 4.17 “Utilities” window, this all new project configuration is complete and click on “OK” to exit the “Option for Target” window, the user can start programming now.
  • Page 18: How To Use Four Wires To Program Or Simulate By T-Link Board

    5. How to use four wires to program or simulate by T-Link Board The T-Link ICE Board can use four wires (VCC, VSS, P3.0/P2.4, P3.1/P2.5) or five wires (VCC, VSS, P3.0/P2.4, P3.1/P2.5, P3.3) to program, user must to select 4-wire in “Utilities dialog box settings”.
  • Page 19: How To Update Tenx Ide & T-Link F/W

    6.1 Update tenx IDE: Click on “Online check” button, and Update the TM52Dll IDE in Utilities dialog box, as shown below. 6.2 Update T-Link F/W: Connect TUT52 Writer to USB and T-Link Board, as shown below. UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 20 T-Link-EV5273/5276/5250 User Manual 6.3 Click on “Update T-Link ICE Board” button to update T-Link Board F/W, as shown below. UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 21: How To Use Touch Key Application

    T-Link-EV5273/5276/5250 User Manual 7. How to use Touch Key Application The Touch Key Application work in Debug Mode, user can use application to view the results of TK Data. The TK Data must be stored in XRAM and IRAM range, as shown below.
  • Page 22 T-Link-EV5273/5276/5250 User Manual 7.2 Click the Debug menu and select “Display Touch Key AP and Run”. UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 23 T-Link-EV5273/5276/5250 User Manual 7.3 Fill in TK Data, ex: TK name (address) and TK Bits and Total TK Channels. 7.4 Click on “OK” button, and the “TK AP” will be show up. UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 24 T-Link-EV5273/5276/5250 User Manual 7.5 TK AP Function, as shown below. UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 25: How To Use Lcd Application

    T-Link-EV5273/5276/5250 User Manual 8. How to use LCD Application The LCD Application can edit and work in Debug Mode, user can use application to simulator LCD Module, please refer to UM-EV22_52XX_LCDAP_SV090 User Manual for more information 8.1 Click on “Option for Target” button in the main menu, as shown below.
  • Page 26 T-Link-EV5273/5276/5250 User Manual 8.3 Click on LCD “Edit Button” and check “show LCD in debug” option, as shown below. 8.4 Click on “Debug” into Debug mode and the LCD Application will be show up, as shown below. UM-T-Link-EV5273_5276_5250_E Rev 0.90, 2016/11/07...
  • Page 27: Q & A

    T-Link-EV5273/5276/5250 User Manual 9. Q & A Q1: How to program a user file on TWR98 Writer? A1: The User must make “ *.tenx” file to program in “Utilities dialog box settings”, or enter “ Download Mode” and “Debug Mode”, as shown below.
  • Page 28 T-Link-EV5273/5276/5250 User Manual Q3: Why the user clicks on “Debug” button as shown below window? When the user writes program file must be avoid to control P3.0/P2.4、P3.1/P2.5 pin (For example: P3、P2 Mode configuration change),if do not show this window in the next time,please check “Do not show next time”...
  • Page 29 T-Link-EV5273/5276/5250 User Manual Q4: Why the user clicks on “Debug” button as shown below window, and then exit the “Debug Mode”? A4: Because the user selects chip model and EV Board model does not match, please recheck chip model and EV Board model.

This manual is also suitable for:

T-link-ev5276T-link-ev5250

Table of Contents