Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Wilton SHR WSHR-3017
- Page 1 Operating Instructions & Service Parts Manual # 28910 ™ Strut and Threaded Rod Shear Record purchase information for quick reference: Document No. M-28910 Edition 1 WILTON 10/2020 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-373-8206 www.wiltontools.com Copyright © 2020 WILTON ...
- Page 2 13. Provide for adequate space surrounding work area and sufficient lighting. ™ Make sure the Wilton SHR is properly supported by the guide bars and bases, so 14. Do not use this machine while tired or under that it will not tip over during use.
-
Page 3: About This Machine
U.S. manufactured brand struts in 12, 14, 16 and 18-gauge mild steel. A single set of blades will provide thousands of clean, even cuts, eliminating the need for deburring. Contact WILTON for special application blade and hydraulic sets. This product has been designed and constructed to provide consistent long-term operation, if used in accordance with instructions as set forth in this document. -
Page 4: Specifications
L = length, W = width, H = height The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, Wilton reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 5: Shipping Contents
Instructions and parts manual Product registration card Remove all contents from shipping carton, and check for shipping damage or missing parts. If either of these is discovered, contact your dealer or Wilton at the phone number on the cover. WILTON ... - Page 6 7.0 Assembly See Figures 2 and 3. Insert two guide bars (A) through the frame holes. The guide bars are identical; however, they must be oriented as shown in Figure 2. Tighten the guide bars in place with the small lock knobs (B).
-
Page 7: Operation
Figure 6 Activate hydraulic power source. Wait approximately 3 seconds for strut to separate. Release hydraulic pressure to allow blade Figure 4 to return to rest position. Remove cutoff piece from back of unit before making additional cuts. WILTON ... -
Page 8: User Maintenance
To cut threaded rod, loosen wing nut to release 9.0 User-maintenance end of threaded rod rest. See Figure 7. Place threaded rod against the rest, in the curve Disconnect from power/ which matches the rod diameter. Slide the rod hydraulic source before performing any through the matching slot in the blade. -
Page 9: Compatibility Chart
Wilton SHR™ Blade Set Deep Only (1-5/8" x 1-5/8") All blade sets include fixed die and moving die. 11.0 Compatibility chart Table 3 The Wilton Strut and Threaded Rod Shear is compatible with the following products. Wilton Brand Compatible strut blade set P1000, P1100, P1000T, P1000SL, P1000HS, P1000H3, P2000 &... - Page 10 12.0 Troubleshooting WSHR-3017 Table 4 Problem Possible cause Remedy Irregular cut. Stock rest not adjusted properly. Adjust stock rest so that strut is perpendicular to cutting die surface. Ensure that knobs are tightened down on guide bars. Locking knobs which hold die in Check tightness of locking knobs frame of main unit have loosened after about every 100 cuts.
-
Page 11: Replacement Parts
Some parts are shown for reference only, and may not be available individually. Non-proprietary parts, such as fasteners, can usually be found at local hardware stores or may be ordered from Wilton. WILTON... - Page 12 13.1 WSHR-3017 exploded view WSHR-3017 Strut & Threaded Rod Shear ...
- Page 13 TS-1523011 Socket Head Set Screw M6 x 1.0P x 6L TS-2361161 Lock Washer TS-2311161 Hex Nut M16 x 2.0P WSHR3017-142 Stock Stop Base WSHR3017-143 Left Tube Plug WSHR3017-144 Special Screw M8 x 1.25P x 23L WSHR3017-145 Compression Spring WILTON ...
- Page 14 M6 x 1.0P x 16L WSHR3017-158 Scale Pointer 6290832 Phillips Pan Hd Machine Screw M5 x 0.8P x 8L LM000428 Warning Label (not shown) LM000429 ID Label (not shown) LM000430 Wilton Nameplate Label (not shown) WSHR-3017 Strut & Threaded Rod Shear ...
-
Page 15: Warranty And Service
Wilton sells through distributors only. The specifications listed in Wilton printed materials and on official Wilton branded website are given as general information and are not binding. Wilton reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. - Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-373-8206 www.wiltontools.com WSHR-3017 Strut & Threaded Rod Shear ...